- Wood - Laminate - Metal - Photos - Concrete - Corian | - Pennies - Shells - Stainless Steel - Marble - Bottle Caps - Sand | - Ceramic - Porcelain - Stickers - Paper -Granite - Bamboo |
High Gloss Hard Crystal Clear Table Top Epoxy Resin Coating Gallon Kit
Item | MTB-3309(A) | MTB-3309(B) |
Appearance | Clear Liquid | Clear Liquid |
Mix Ratio by weight | |
Operation Time(H) | |
Curing Time(H) | |
Cured Time(D) | |
Solid Content(%) | |
Levelling roperty(Grade) | |
Operation Method | |
Operation Temperature | |
Coverage Data(1mm) | 0.8kgs/sqm |
Mixed Viscosity(Cps) | |
Compressive Strength | |
Wear resistance (mg) | |
Fineness (μm) | |
Shelf Life (M) | |
Package | 16oz/set, 32oz/set, 4L/set and 20L /set ,accept OEM&ODM |
Using Instruction
High Gloss Hard Crystal Clear Table Top Epoxy Resin Coating Gallon Kit
How to use MTB-3309 Ultra Clear Table Top Epoxy Coating /Extremely Durable Table Top Finish?Step 1: Measure EpoxyMTB-3309 Clear Epoxy is a two-part, epoxy coating that is mixed at a 3 to 1 ratio. Pour an equal amount of hardener and resin into a new container. It is important that you use a new container for each batch that you mix so that the next batch does not get contaminated from the remnants of curing epoxy in the previous container.
Step 2: Mix Epoxy
Mix thoroughly with our mixing drill bit to ensure that the batch is completely blended.
Step 3: Paint on a Seal Coat of Epoxy
On porous material such as wood, you will need to paint on a seal coat of the same epoxy first to seal any pores in the surface. This prevents air bubbles from forming in the following flood coat. Not all surfaces require a seal coat. Contact customer service if you are unsure if your project will need a seal coat as you will need to figure the seal coat into your epoxy order to make sure you have enough product.
Step 4: Pour Epoxy Flood Coat
Pour the epoxy onto the surface working your way down the length of the area. The epoxy self levels so there is no need to move it around with any tools. The epoxy coat can be allowed to flow over the sides which will create a coating on the vertical edges. The epoxy that drips over will form bumps about 1/2 inch underneath the lip of the edge. These drips can be sanded off once the epoxy has cured.
*Multiple flood coats can be applied to cover over embedded objects. Just pour a new flood coat every 4 hours.
Step 5: Pop Air Bubbles with a Plumber's Torch or Heat Gun
Once you finish pouring the epoxy, you will need to pop air bubbles using a plumber's torch or a heat gun (not a hair dryer). This process is the easiest step as it only takes about 30 seconds to 1 minute to do. Keep the torch or heat gun a few inches from the surface and simply wave it back and forth until you cover the entire distance of the surface. The heat pops any bubbles instantly.
Finished Project
The epoxy is dry to the touch in 12 hours. Allow 72 hours before using the surface. That's it!
Working Temperature of MTB-3309 Clear Ultra Clear Table Top Epoxy Coating /Extremely Durable Table Top Finish
The working room temperature must be above 75 degrees, several hours prior to mixing the epoxy. We recommend that the product be brought inside and acclimated to room temperature, as it will be cold during winter shipping months. Use space heaters if necessary to ensure the temperature remains above 75 degrees in cold areas, such as garages and basements. It is extremely important that the temperature remain above 75 degrees for a full 72 hours, in order for the epoxy to cure. High or low humidity and higher temperatures (75-110 degrees) are perfectly fine for curing; the epoxy cures much faster with higher temperatures.
Packaging & Shipping
High Gloss Hard Crystal Clear Table Top Epoxy Resin Coating Gallon Kit
We have below packages for you choice,
--16oz kit
--320z kit
--1gallon kit
--2gallons Kit
--20kgs Kit
Contact Supplier for more details
Company Profile