Description
ZMP1110 SSEDU Pneumatic and electro-pneumatic bench mechatronics training equipment educational equipment teaching Jinan
Pneumatic and electro-pneumatic bench Double-sided mobile workstation allows the assembly and operation of the various components without the use of tools (components equipped with quick assembly system)- 1* Rolling table dimension between length 1200 mm, height 1700 mm and depth 800 mm minimum.- 1* extruded and adonized aluminum plate of dimension between 1080 mm length and 680 mm depth minimum with the possibility of fixing the electrical components on both sides.- 2* cabinet with a minimum of four drawers and locks - 1* cable guide- 1 x power supply unit for mounting frame 220V AC- 24 VDC/ 4A minimum with minimum 6 outputs- 1 x silent lubricated compressor for classroom use: protected by pressure switch and safety valve - Supply voltage 230V/50HZ- Operating pressure 7 bar minimum - Suction flow rate 40 L/MIN minimum - Tank volume 9 L minimum - Outlet with pressure regulator, pressure gauge and quick coupler Pre-actuator for manual and mechanical pressurization - 2 push-button operated 3/2 NC spool valves- 2 Push-button operated 3/2 NO dispensers- 1 3/2 NC valve operated by emergency stop button- 4 Distributors FC 3/2 NC roller-operated- 2 NC 3/2 directional control valves operated by retractable roller- 1 Switch operated 3/2 NC bistable valve- 1 Push button operated 5/2 directional control valve- 1 5/2-way valve with two-position selector switch- 1 Closed center 5/3 valve operated by hook-in leverPneumatically operated pre-actuator - 1 Pneumatically operated 3/2 NC monostable spool valve, 3/2 NC.- 2 Pneumatically operated 5/2 monostable spool valves- 2 Pneumatically operated 5/2 bistable valves Signal processing, flow control and blocking - 1 logic gate "OR".- 1 "OR" circuit selector switch- 1 "AND" logic gate- 1 "AND" circuit selector switch- 2 unidirectional flow throttles- 1 Quick exhaust valve- 1 Adjustable pneumatic timer with positive output- 2 Flow regulators with pilot operated check valve- 1 bi-directional flow restrictor- 1 Sequence valveCylinders- 2 Single-acting spring return cylinders- 1 Double-acting cylinder with magnetic piston and elastic damping- Double acting magnetic piston cylinder with adjustable pneumatic damping Electro dispensers- 1 Solenoid valve, 3/2-way monostable NC (24 VDC coil with LED indicator)- 1 Solenoid valve, 3/2 bistable (24 VDC coil with LED indicator)- 2 Solenoid valves, 5/2 bistable (24 VDC coil with LED indicator)- 2 Solenoid valves, 5/2 monostable (24 VDC coil with LED indicator)- 1 Solenoid valve, 5/3 closed center (24 VDC coil with LED indicator)- 1 Vacuum generator by suction effect with suction cup- Control modules/sensors- 1 ON/OFF switch- 1 Emergency stop push button (electric)- 1 Set of electrical inputs (Box with 3 NO-NC pushbuttons)- 1 Set of 3 relays (3 NO-3 NC, 24VDC coil)- 1 Indicator (Indicators, ringer)- 1 Set of 2 timer relays (2 NO- 2 NC)- 1 Electrical connection terminal block- 4 Magnetic detectors type Reed- 2 Static magnetic detectors- 1 Inductive sensor- 1 Capacitive sensor- 1 Photoelectric detector- 4 Electric limit switch- 1 Electrical contact pressure switch- Accessories- Set of 10 "T" Connectors Ø 4mm- Set of 10 plastic caps Ø 4mm- Set of 10 "Y" connectors Ø 4mm- 1x 4 mm safety laboratory cable set (color red and blue) consisting of at least 80 cables- all pneumatic components must be equipped with Ø 4mm quick couplingsIII.Experiment list Basic pneumatic1) function demonstration experiment of common pneumatic components;2) common pneumatic circuit demonstration experiment:3) the commutation circuit of the single-acting cylinder4)The reverse circuit of the double acting cylinder5) the speed regulation loop of single-acting cylinder (one-way, two-way)The speed regulating circuit of inlet speed of double acting cylinder7) the speed regulating circuit of the speed adjustment of the two acting cylinder8) speed switching circuit9) the buffer circuit of parallel throttle valve is adopted10) interlocking loop11) overload protection loop12) unloading loop13) single cylinder continuous reciprocating control loop14) two - cylinder continuous reciprocating control loop15) use the cylinder sequence of the stroke valve16) double cylinder sequence action loop with electrical switch (magnetic switch, proximity switch)17) multi-cylinder sequential action loop18) two - cylinder synchronous motor loop19) secondary pressure control circuit20) high and low voltage conversion circuit21)Counting loop22) delay loop23) the hand operating circuit24) the application circuit of the valve25) or the application circuit of the door - type shuttle valve26) quick exhaust valve application circuit
Electro pneumatic with PLC1) PLC instruction programming, trapezoidal programming learning2) the learning and use of PLC programming software(we supply free edition(free editon) software with unlimited users)3) PLC and computing communication, online debugging4) control experiment of PLC and pneumatic combinationIV.Components Basic pneumatic components for each bench :- 2 switch buttons 3/2, normally closed- 1 switch button 3/2, normally open- pressure indicator with 2 colors- manual selector 5/2- push-pull button 3/2 normally closed- roller operated valve 3/2 normally closed- 2 proximity sensors, pneumatic fixed on the actuator- 2 pneumatic temporizers, normally closed- sequence valve- unilateral 3/2 distributor, with pneumatic command- unilateral 5/2 distributor with pneumatic command- bi-lateral 5/2 bi-stable distributor, with pneumatic command- OR logic function- & logic function- fast evacuating valve- 2 unidirectional flow limiters- simple effect actuator- double effect actuator- pressure filter-regulator with pressure supply distributor- pressure regulator with manometer- 2 manometers- air cross connect- 2 plastic hoses- pneumatic motor- pneumatic sequencer
Basic electro-pneumatic components for each bench:- electric buttons module- electric relays module- temporized relays module- electronic pre-selection counter module- emergency stop button- inductive proximity sensor- capacitive proximity sensor- distributor terminal-swing check valve- electro-distributor with LED- manometer- pressure supply distributor with filter pressure reducerPneumatic regulation components:- electric buttons module- push button normally closed- proportional electro-distributor (5/3, …)- electro-distributor with LED (5/3 normally closed, 3/2 normally closed, …)- monometer- unidirectional flow limiter- pressure supply distributor with filter pressure reducer- air cross connect- plastic hoses- linear actuator, with guidance and all necessary accessories- PID regulator- comparison card- analog pressure sensor- pneumatic capacitors- status regulator- all necessary accessories for pneumatic regulation (potentiometer, damper, weight, …)PLC equipped at least by:- 24 VDC power supply- Processor: 192 k bytes or better, memory 512 K bytes or better- network interfacing (Profinet, Ethernet, USB, …)- 16 digital inputs 24 VCC, potential separation LED light indication- 16 digital outputs 24 VCC, 0.5A with galvanic separation and protection against short circuit- 2 analog inputs- 2 analog outputsSupplied with Siemens S7-314CPLC:- multi-users software teaching edition PLC programming including different languages(we supply free edition(free editon) software with unlimited users)- connection PC-PLC- spare parts set- accessories set: . electrical wires . plastic hoses . hoses connecting tools . spare parts of first use- practice activities manual book- instruction book for the teacher including solutions for the practice activities- silent air compressor with 30L, 8 bars minimum- multi-users software for pneumatic and electromagnetic circuit simulation.
Product Details and Warranty
We supply suitable spare pats according to experiment requirement, our products take aluminum structure, A4 paper dimension aluminum and plastic hanging box structure.
We supply 3 years warranty time. Please se photo for foreign sales department and photo for spare parts.
Packaging & Delivery
Package details: plastic film+ plastic foam + plywood box with pallet, and for equipment dimension less than 1CBM, we supply plastic film+ plastic foam+ fine carton.
Arrange delivery within 45 days upon receipt of payment.
Please see below photo for detailed package.
Company Information
We supply professional educational training equipment and technical teaching equipment, which has been widely applied in Engineering Universities, Polytechnics, Technical Institute, Vocational Schools as well as Industry workforce Development Programs and Training Center. Our products allow students to learn and experiment through valuable hands-on experience, and the technology covered by our training equipment provides knowledge, experiments and didactic skills development that are of critical importance to today's and tomorrow's careers.
Photo for Clients Visiting Factory
Photo for Workshop and Equipments
Service
We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.
Certificate
Our products takes ISO9001 product management system.
No. | Feature Name | Details |
1 | Customer design | Yes |
2 | Warranty | 1 year, 2 years, 3 years or 5 years according to client requirements |
3 | Package | Plastic film+ carton+ Fine plywood |
4 | Products standard | International didactic equipment standard |
5 | Application range | Educational equipment for university, college, vocational training centers |
6 | Company philosophy | Supply best quality Chinese products to the worldwide schools. |
7 | Self owned brand | Shouldshine, SSEDU, JSS. |
8 | Production time | From 10 days to 60 days according to different items |
Complaint
