Description
RJ45 Digital Remote Control Signal Jammer Low Electromagnetic RadiationModel:GW-J800DNW
Wireless Control System: Jail Jammer System Software
1) Each unit have a control I/O Board (RF module) with hard relays (for alarm trigger) via wireless output for data transmission to control of all functions of each unit.- to be controlled via software program on remote PC workstation by wireless
2) Each Unit be able to send Alert to the remote control PC workstation by wireless, if any of the RF frequency bands fails individually from each of the units (VSWR Alarm: Antennas Lost Connection, Module Failure)
3) All units have individual digital ID to identify them through the PC workstation.
4) The wireless data will travel to converter in main office and then convert to RJ45 so it can then communicates with a PC workstation computer.
5) Prison Jamming system The software can Turn On/Off, each band, each jammer or the whole jammer system
6) Jammer Unit housing unit is waterproof and heat sink
Digital noise technology jamming range is very high, 5 times stronger than VCO technology jammer.
Digital Gaussian white noise is essentially a pseudo random signal, signal characteristics consistent with a random function. Strong Anti-interference ability, there is no need high power interference radiation power, influence and damage to the electromagnetic environment is very small, can bear long distance loss. Long-term cases, interference stability. Mechanism causes due to interference, interference by external environment (such as wind, rain, ice, variations on space) change is not obvious.
The Prison Jammer GW-J800DNW manages the problem of illegal cell phones in a Prison or Government facility. Prison Solutions from government stop smuggled phones from making calls by using RF Jammers.
Our solutions are good at operation and design. Prison Jammers work to block off large areas in a building to stop cell phone calls. These Prison Jammers are installed in a pre-determined pattern.
Using digital Gaussian white noise technology for Maximum performance. Will cut-off all Cellular Communication between Mobile Phones and Cellular cells.
Technical Specification: | Output interface | Description | Shield band of frequency | RF output power( +1dBm) |
| CH1 | GSM850 | 851-894 MHz | 46dBm |
| CH2 | AWS 1700 | 2110-2155 MHz | 46dBm |
| CH3 | GSM900 | 925-960 MHz | 46dBm |
| CH4 | PCS 1900 | 1930-1990 MHz | 46dBm |
| CH5 | WIFI, 2.4G | 2400-2485 MHz | 43dBm |
| CH6 | LTE 2300 | 2300 - 2400MHz | 46dBm |
| CH7 | CDMA450 | 460 - 470 MHz | 46dBm |
| CH8 | LTE700 | 758 - 803 MHz | 46dBm |
| Power supply: AC220V, or 110V |
| Total Output Power: 300Watt |
| Power consumption:1000Watt |
| Weight: 65Kg Size(length × wind × high):720×490×240mm |
| Humidity: 5%-95% Running Temperature: -20ºC to +55ºC |
| Cooling System | Systematic Smart Cooling System |
| System Protection | VSWR, temperature |
| Jamming Source | Digital Gaussian white noise technology |
| Antenna Type | High Gain Directional Panel Antennas |
| Number of Antennas | 3 |
| Jamming range: 100-600m according to signal density of mobile network |
There are 3 types RF Jammers:
1. VCO(voltage controlled oscillator) Technology
2. DDS (Direct Digital Synthesis)Technology
3. Pseudo random digital Gaussian white noise technology.
General speaking:
1. VCO(voltage controlled oscillator) Technology
Requirements for the jamming range is not high, extremely sensitive civilian consumption levels of low cost, but efficiencies are not very strict scene.
2. DDS (Direct Digital Synthesis)Technology
Requirements for the jammer need wideband frequency range, and choose different frequency range, such as 20-3000MHz NO gap jamming.
3. Pseudo random digital Gaussian white noise technology.
Requirements for the jamming range is very high, can accept high cost, national security and military, have strict requirements for jamming range.
Features:
High-power multi-band jammer, make high jamming range
Modular construction for easy maintenance, repair and upgrade.
Max 300watts total RF output power.
Special additional housing for all weather protection.
The general design of the system meets military requirements.
Different frequency band can be controlled independently by single switches;
Power Amplifiers protection design ensures the working reliability of the device.
(Optional)Can customize these frequencies AM, FM, VHF, UHF, 450MHz, iDEN, CDMA, GSM, GPRS, DCS, PCS, AWS, WCDMA, LTE 700, LTE 800, LTE 2300, LTE 2600, GPS, WIFI, WIMAX, etc.
Advantages:
1. VSWR protection,
When there be antenna disconnect, full system will not burn out.
2. Waterproof Level: IP63
Good cooling system, Continuous operation, even in hot climates.
3. Stable capability, cost-effective choice
4. Each channel can be controlled separately and simultaneously.
Manual adjustable output power with each channel.
allow the total blockade without interference of the people who live outside the perimeter of the prison.
5. Remote Monitoring(Optional)
Remote Monitoring available by Ethernet Network
Remote Control Interface: RJ45
Provide a system (software and hardware) that allows the authorities to supervise the operation at 100% of the blocking system.
6. Small influence to the electromagnetic environment.
Comply with the maximum power allowed for non-ionizing radiations that affect the health of people.
Application
Prisons, military, government, Oil and Gas Storage Facilities and fields, Churches, Theatres, News Conference Rooms, Libraries, Museums, Courts, Border Patrol and Drug Enforcement, Customs, mosques, etc.Recommended Accessories:1) Donor antenna: Log Periodic Antenna (9dBi,806-960/1710-2700MHz)
2) Service antenna: Omni Ceiling Antenna (3dBi,806-960/1710-2700MHz)
3) 5D-FB coaxial cable with connecter (Cable length optional)Method of Installation:The booster is fixed onto the wall through expansion bolts.
A. Drill holes in the selected place and install expansion bolts.
B. Align the holes with the expansion bolts, place flat washers, spring washers, and nuts in turn, and tighten the nuts to fasten the installing support.
C. Place the booster on and fasten it.
D. Connect cables and power cables to the booster respectively.
E. After installing the booster as described above, power on the booster to check the operation status.Connection:A. BTS Port: donor antenna cable is connected with Outdoor Port;
B. MS Port: service whip antenna is connected with Indoor Port;
C. DC IN connected with Power adaptor.Q1.Payment Method
T/T, Western Union, Paypal, and Credit Card are available,
and we suggest paying by Alibaba Trade Assurance, the most favor, and security method.
*Other methods please Contact us with more details.
Q2.Delivery Date&Lead Time
| Quantity | Lead time | Delivery to American/Middle East/Asia/Europe |
| <20 pcs | 3-5 business days | 3-7 business days by DHL
5-7 business days by FedEx/UPS |
| 20-100 pcs | 7-15 business days |
| >100 pcs | 15-24 business days |
*Click it to get the sample.Q3. Can I customize frequencies?
Yes, we can customize 2G/3G/4G/5G/GSM/CDMA/DCS/AWS/PCS/WCDMA/LTE,etc.
Q4. What should I do if I don't know about frequency in my country?
Please feel free to Contact us with your inquiry, we will find the frequency you need and address your problems.
More signal repeater please CLICK it!
Complaint
