Complaint
| 20Feet 25CBM T11 Sulfuric&Phosphoric Acid& compound Fertilizer Tank Container with CSC, ASME, LR Certificates | ||||||
| Outer Dimension | Length(mm) | 6058mm | ||||
| Width(mm) | 2438mm | |||||
| Height(mm) | 2591mm | |||||
| Transportation/Storage material | Sulfuric&Phosphoric Acid& compound Fertilizer | |||||
| Max gross weight | 36000 kg | |||||
| Tare weight | 3.6tons(±3%) | |||||
| Type approvals | UN portable tank T11, IMDG, ADR/RID, TIR, CSC, UIC, TC, UK DfT, US-DOT CFR49 | |||||
| Nominal Capacity | 25000L(±0.75%) | |||||
| Portable Tank instruction | T11 | |||||
| Design code | ASME VIII DIV 1 | |||||
| Design temperature | -40 ~ +130 ºC | |||||
| Desgin pressure | 4bar | |||||
| External desgin pressure | 0.41 bar | |||||
| Material | ||||||
| Frame | SPA-H or equivalent | |||||
| Tank Shell | SANS 50028-7 Type 1.4402/1.4404 (C<=0.3%), ASTM A240 316L | |||||
| Finish | Cold Rolled 2B | |||||
| Tank Heads | SANS 50028-7 Type 1.4402/1.4404 (C<=0.3%), ASTM A240 316L | |||||
| Finish | Cold Rolled and polished with 180 grits | |||||
| Maximum allowable working pressure | 4 bar | |||||
| Test pressure | 6 bar | |||||
| 25000L Tank | ||||||
| External desgin pressure | 0.41 bar | |||||
| Shell Nominal | 4.40mm Minimum: 4.2 mm | |||||
| Head Nominal | 4.70mm Minimum: 4.50 mm | |||||
| Manhole | 500 mm, 8 mm × 90 mm Neck Profiled and Compensated, Fort Vale part No. E4D/8518025BT. 8 point fixing with Super Tanktyt Lid seal for corrosive cargo | |||||
| Safety Relief Assembly | 1 × 2½" BSP Supermaxi Highflow relief valve, pressure only model set at +4.4 bar (63.8psi), Fort Vale Part No. 010/16300.1 × provision for a second valve. | |||||
| Air line valve | DN 40 ball valve terminating with 1½" BSP connection and cap, Fort Vale part No. 530/0000G. | |||||
| Top outlet | Provision only, DN80 tank pad, Fort Vale part No. 368/0800, fitted with PTFE gasket & blind flange. | |||||
| Bottom Discharge Prov. | 45°Hi-Lift Footvalve fitted with a clamped butterfly valve terminating with a 3" BSP spigot with cap and chain, Fort Vale part No. 804/0010A. | |||||
| Spill box | Middle spill box fitted around manlid and safety relief valve; Rear spill box fitted around airline valve and top outlet provision. Each box equipped with 2 PVC drain tubes. | |||||
| Steam Heating System | 8 longitudinal heating channels provided, giving a total effective heating area 10 square meters. Working pressure 4 bar, test pressure 6 bar. Inlet 3/4" BSP, outlet 3/4" BSP, dust cap fitted. A drainage provision with 3/8" BSP is fitted to the outlet pipe. | |||||
| Remote Control system | Φ 3 mm stainless steel cable coated with plastic is fitted to the bottom rail of right side. And an emergency decal is fitted above the cable. | |||||
| Fusible link | Provision | |||||
| Dipstick | Provision, dipstick bracket is fitted to the neckring of the manlid, | |||||
| Thermometer | Dual scale thermometer, -40~160 ˚C (-40~320 ˚F), fitted on rear end to lower left side. | |||||
| Document holder | Φ 80 mm plastic document holder is fitted to the rear right hand side beam. A drain hole is provided at the lowest point. | |||||
| Insulation & cladding | ||||||
| Insulation | 50 mm thick Rockwool (50kg/m³) where possible | |||||
| Cladding | Shell | 1.8 mm thick white GRP (RAL9010) with butt joints. With 6-off stainless steel strip (0.8*60*C). Sealed by silicone sealant. Φ10mm drain hole per panel on bottom. | ||||
| Ends | 2 mm thick mould GRP end | |||||
| Frame Details | ||||||
| Type | Full frame beam design ISO 1496/3 (1CC) with hollow section bottom rails. | |||||
| Corner castings | ISO 1161 8-off in total | |||||
| Ladder(s) | Non-slip stainless(304 S/S) at rear right hand side | |||||
| Walkway | F type 475mm wide non-slip aluminium | |||||
| Earthing lug | Stainless(304 S/S), fitted to rear bottom member | |||||
| Painting | Carbon steel shotblasted to SA 2½ profile. | |||||
| COATING / INSULATION | ||||||
| Tests | 36000kg | |||||
| Stacking at | 192000kgs | |||||
| Transverse Racking test | 150000 Newtons | |||||
| Impact test at | SRS Method a / at R = 36000 kg | |||||
| SUBSTANCES SUITABLE FOR TRANSPORT: In accordance with the requirements of the applicable regulations and the construction of the tank and its equipment. (Substances not compatible with the tank and/or its accessories are excluded for transport) | ||||||
Q: I want the Liquid Tank Container with heating system, especially the steam heating system, can you supply?
A: Yes, the steam heating system is the option configuration, you can choose it as you want.
Q: Do you have the certificates to meet us the transportation ways of the land truck, Sea Boat and Railway?
A: Yeah, of course, but the price will be very different by different transportation ways; So kindly please let me know your exact transportation ways before the quoting; And also the certificates will be ready after the tank container passed all kinds of the testing&inspection.
Q: Do you have the stocked tank containers?
A: Yes, but the price will be higher than the normal one.
Q: Can I have the drawings of this ISO Storage tank containers?
A: Yeah, the existing simple similar drawings of the tank container for your reference only for the beginning, will make the more precise drawings after getting the down payment, and will send this drawing to you for your confirmation before production.
Q: Can I make the discharging valves at the bottom?
A: Yes, the discharging valves can be at the bottom or at the top, you can choose as your actual request.
Q: How can I pay the money without risk?
A: You can pay the money to us via Alibaba Trade Assurance, then the alibaba can guarantee your money safe and the delivery on time.
Q: Can I do your agent in our country or some district?
A: Yes, if you quantity is enough, no problem, the 50units for the first time is okay.
