Complaint
1.Specification
| Shenzhen Li-ion Battery Bodyguard Technology Co.,LTD | |||
| PCM Specifications For 14.8V(4S)Li-ion battery Packs | |||
| Modle: LWS-4S5A-506(4S) | |||
| No | Test item at 25 ºC | Criterion | |
| 1 | Communication protocol | SMBUSE communication | smbc=SCL/smbd=SDA |
| 1 | Voltage | Charging voltage | DC:16.8V CC/CV(4.2V/1Cell) |
| 2 | capacity | Design capacity of battery pack | 5800mAh/EVE cell |
| 3 | current | Current consumption (software) | <400uA |
| Current consumption (sleep mode) | <150uA | ||
| Maximum continuous charging current | 3A | ||
| Maximum continuous discharging current | 8A | ||
| 4 | Overcurrent protection (one pole protection) | Overcharge detection current | 4A |
| Detection delay time | 3s | ||
| Overdischarge detection current | 12A | ||
| Detection delay time | 3s | ||
| 5 | Overcurrent protection (two pole protection) | Overcharge detection current | 10A |
| Detection delay time | 1s | ||
| Overdischarge detection current | 13A | ||
| Detection delay time | 1s | ||
| Overcurrent protection (three pole protection) | Overdischarge detection current | 20A±1A | |
| Detection delay time | 15-50mS | ||
| Recovery current | 200mA | ||
| 6 | Single over charge protection | Overcharge detection voltage (level I) | 4.25±0.025V |
| Over charge detection delay time | 2S | ||
| Overcharge detection voltage (level 2) | 4.3±0.025V | ||
| Over charge recovery voltage | 4.05±0.05V | ||
| Over charge detection recovery delay time | 2s | ||
| 7 | Single over discharge protection | Over discharge detection voltage | 2.7±0.1V |
| Over discharge detection delay time | 2s | ||
| Over discharge recovery voltage | 3.0±0.05V | ||
| 11 | Short circuit protection | Detection status | P+,P- short circuit |
| Detection delay | 200-500us | ||
| Recovery status | Cut load | ||
| 12 | internal resistance | Protection line | ≤20mΩ |
| 13 | Over temperature protection (level 1) | Charge | 50ºC±5ºC |
| Charge delay time | 2s | ||
| Over temperature charge recovery | 45ºC±5ºC | ||
| Discharge | 70ºC±5ºC | ||
| Discharge delay | 2s | ||
| Discharge detection delay time | 60ºC±5ºC | ||
| 15 | Temperature | Operating temperature range | -20~+65ºC |
| Storage temperature range | -20~+75ºC | ||
| SRENSE file | Internal documents | lws-4s5a-506 5.8ah eve | |
| 1: The protection board adopts Eve 2900mah electric core aging successfully. If you need to change other cells, you need to make samples and write data again. | |||
| 2: The voltage and current of the protection plate have been calibrated at the factory, but it needs to be calibrated again when assembled on the battery. Otherwise, there will be a little deviation, but not too much deviation. | |||
| 3: After the battery is assembled, it needs to run another cycle (0.5c/16.8v charge cut-off current 130mA, standstill for 10min, 0.5c discharge cut-off voltage 11.6v, standstill for 10min). 0.5c charging cut-off voltage 14.8V cut-off current 200mA). | |||
| 4: The protection board has two-stage charging protection function. It is necessary to assemble the protection plate on the battery to test whether the function is OK before short circuiting the short contact of J1 (arrow position in the figure below). When assembling the protection board, the voltage of single power saving cell shall not exceed 3.9v (overcharge recovery voltage of secondary protection IC), so as to prevent the secondary protection IC from misoperation and damaging the fuse. | |||
2.Company informationOnly as a general reference parameter. If you have special requirements for some parameters, please contact the service personnel, and we will send the new specifications according to your requirements(Li-ion or lifepo4)
Shenzhen Li-ion Battery Bodyguard Technology Co.,Ltd was founded in 2013.
Mainly provide Battery PCM & BMS for Lithium ion ,Lifepo4 ,LTO battery pack.
Since 2013, the company has more than 400 types of hardware PCM/BMS,and software BMS including HDQ/12C/SMBUS/RS482/RS232 & Bluetooth and so on. Mainly covers battery assembly 1S-35S in series ,working current up to 350A;the products are widely used in solar street lamp,golf ,LED light,power tool,electric bicycle,medical equipment,EV application......etc.
(Widely used)
3.Transportaion
Packing: Inner packing:Vaccum packing/Plastic bag.
Outer packing:Standard carton packing or packing per customer's requirements.
Delivery type:by air such as TNT,UPS,FEDEX or by sea ,just depend on your convenient.
Payment:L/C,T/T,Western Union,PAYPAL ,Bank ,etc.
4.FAQ
Q: How do I judge what material my battery is ?
A: Please take a look at the battery body.if the normal voltage of your battery shows as 3.2V,the battery will be LiFePo4.If the normal voltage of your battery shows as 3.6V or 3.7V, the battery will be Li-ion or Li-polymer battery. you can also ask battery manufacturer the material of battery.
Q: Can I use this protection circuit board for my battery?
A: Can use this protection circuit board, or not?
There are 2 questions:
How much cells in series is your battery pack?
The protection circuit board you need to buy must be same cells in series as your battery pack.
What material is your battery?
Only the LiFePo4 battery has different electric parameter from other battery, so if you need buy the protection circuit board for LiFePo4 battery , Please let us know firstly.
Q: Do we need cell balance or not?
A: The function of balance : Since battery is made of many pcs of cells in parallel and in series, the cells can't be the same as no two people in the world is the same , so can only put in group with similar performance is not without balance function
Q: Do you have Minimum Order Requirement (MOQ)?
A: No, We don't have MOQ, Different customer have different requirement ,We can provide various capacity and size as per your requirements,Also ODM / OEM is welcome.
About your products,just tell us the relative voltage/ cells/ current A or equipment etc,we will help to recommend the most suitable products for you.
