Brocade 10g-Sfpp-Bxu-80K Compatible 10gbase-Bx80-U Bidi SFP Fiber 1270nm-Tx/1330nm-Rx 80km Dom Transceiver Module

Min.Order: 1

Product origin: Shenzhen, Guangdong, China

Infringement complaint:

Complaint

US$ 5 ~ 128

Description

10G BiDi SFP/XFP module with 80KM transmission distance.

Product Features

Hot-pluggable XFP footprint
Supports 9.95Gb/s to 11.3Gb/s bit rates
XFI Loopback Mode
RoHS-6 Compliant (lead-free)
1270nm DFB laser and PIN receiver for LASX-T2733X-ER
1330nm DFB laser and PIN receiver for LASX-T3327X-ER
Power dissipation<2W
Case operating temperature 0 ºC~70ºC
Up to 40km transmission on SMF
2-wire interface with integrated Digital Diagnostic monitoring
EEPROM with Serial ID Functionality
Compliant with XFP MSA with LC connector

Applications

10GBASE-BX 10.3125Gb/s Ethernet
10GBASE-BX 9.953Gb/s Ethernet
SONET OC-192 &SDH STM I-64.1

Product Description

LASX-T2733(3327) X-ER is hot pluggable 3.3V Small-Form-Factor transceiver module. It designed expressly for high-speed communication applications that require rates up to 11.3Gb/s, it designed to be compliant with XFP MSA. The module data link up to 40km in 9/125um single mode fiber.

Absolute Maximum Ratings

Parameter	Symbol	Min.	Typ.	Max.	Unit	Note
Storage Temperature	Ts	-40	-	85	ºC
Relative Humidity	RH	5	-	95	%
Power Supply Voltage	VCC	-0.3	-	4	V
Signal Input Voltage	VCC	Vcc-0.3	-	Vcc+0.3	V

Recommended Operating Conditions

Parameter	Symbol	Min.	Typ.	Max.	Unit	Note
Case Operating Temperature	Tcase	0	-	70	ºC	Without air flow
Power Supply Voltage	VCC	3.14	3.3	3.47	V
Power Supply Current	ICC	-	-	600	mA
Data Rate	BR	9.95	10.3125	11.3	Gbps
Transmission Distance	TD	2	-	40	km
Coupled fiber	Single mode fiber

Optical Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Note
Transmitter
Average Launched Power	Pout	0	-	5	dBm
Average Launch power of OFF transmitter	P_OFF	-	-	-30	dBm	Note (1)
Centre Wavelength Range	λC	1260	1270	1280	nm	LASX-T2733X-ER
Centre Wavelength Range	λC	1320	1330	1340	nm	LASX-T3327X-ER
Side mode suppression ratio	SMSR	30	-	-	dB
Spectrum Bandwidth(-20dB)	σ	-	-	1	nm
Extinction Ratio	ER	3.5		-	dB	Note (2)
Output Eye Mask	Compliant with IEEE 802.3ae requirements					Note (2)
Receiver
Input Optical Wavelength	λIN	1320	1330	1340	nm	LASX-T3327X-ER
Input Optical Wavelength	λIN	1260	1270	1280	nm	LASX-T2733X-ER
Receiver Sensitivity in average	Psen	-	-	-15	dBm	Note (3)
Input Saturation Power (Overload)	PSAT	0.5	-	-	dBm	Note (3)
LOS -Assert Power	PA	-32	-	-	dBm
LOS -Deassert Power	PD	-	-	-18	dBm
LOS -Hysteresis	PHys	0.5	-	4	dB

Note:
1. The optical power is launched into SMF
2. Measured with RPBS 2^31-1 test pattern @10.3125Gbs
3. Measured with RPBS 2^31-1 test pattern @10.3125Gbs BER=<10^-12

Electrical Interface Characteristics

Parameter	Symbol	Min.	Typ.	Max.	Unit	Note
Total power supply current	Icc	-	-	600	mA
Transmitter
Differential Data Input Voltage	VDT	120	-	820	mVp-p
Differential line input Impedance	RIN	85	100	115	Ohm
Transmitter Fault Output-High	VFaultH	2.4	-	Vcc	V
Transmitter Fault Output-Low	VFaultL	-0.3	-	0.8	V
Transmitter Disable Voltage- High	VDisH	2	-	Vcc+0.3	V
Transmitter Disable Voltage- low	VDisL	-0.3	-	0.8	V
Receiver
Differential Data Output Voltage	VDR	300	-	850	mVp-p
Differential line Output Impedance	ROUT	80	100	120	Ohm
Receiver LOS Pull up Resistor	RLOS	4.7	-	10	KOhm
Data Output Rise/Fall time	tr/tf	20	-	-	ps
LOS Output Voltage-High	VLOSH	2	-	Vcc	V
LOS Output Voltage-Low	VLOSL	-0.3	-	0.4	V

Pin Assignment

Diagram of Host Board Connector Block Pin Numbers and Name

Pin	Logic	Symbol	Name/Description	Note
1		GND	Module Ground	1
2		VEE5	Optional -5.2 Power Supply - Not required
3	LVTTL-I	Mod-Desel	Module De-select; When held low allows the module to respond to 2-wire serial interface commands
4	LVTTL-O	Interrupt	Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface	2
5	LVTTL-I	TX_DIS	Transmitter Disable; Transmitter laser source turned off
6		VCC5	+5 Power Supply
7		GND	Module Ground	1
8		VCC3	+3.3V Power Supply
9		VCC3	+3.3V Power Supply
10	LVTTL-I	SCL	Serial 2-wire interface clock	2
11	LVTTLI/O	SDA	Serial 2-wire interface data line	2
12	LVTTL-O	Mod_Abs	Module Absent; Indicates module is not present. Grounded in the module.	2
13	LVTTL-O	Mod_NR	Module Not Ready; LINK-ALL defines it as a logical OR between RX_LOS and Loss of Lock in TX/RX.	2
14	LVTTL-O	RX_LOS	Receiver Loss of Signal indicator	2
15		GND	Module Ground	1
16		GND	Module Ground	1
17	CML-O	RD-	Receiver inverted data output
18	CML-O	RD+	Receiver non-inverted data output
19		GND	Module Ground	1
20		VCC2	+1.8V Power Supply - Not required
21	LVTTL-I	P_Down/RST	Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset
21	LVTTL-I	P_Down/RST	Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle.
22		VCC2	+1.8V Power Supply - Not required
23		GND	Module Ground	1
24	PECL-I	RefCLK+	Reference Clock non-inverted input, AC coupled on the host board - Not required	3
25	PECL-I	RefCLK-	Reference Clock inverted input, AC coupled on the host board - Not required	3
26		GND	Module Ground	1
27		GND	Module Ground	1
28	CML-I	TD-	Transmitter inverted data input
29	CML-I	TD+	Transmitter non-inverted data input
30		GND	Module Ground	1

Notes:
    1. Module circuit ground is isolated from module chassis ground within the module.
    2. Open collector; should be pulled up with 4.7k - 10kohms on host board to a voltage between 3.15V and 3.6V.
    3. A Reference Clock input is not required by the LASX-T2733(3327)X-ER. If present, it will be ignored.

Digital Diagnostic Functions

As defined by the XFP MSA, Linksall XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters:
          Transceiver temperature
          Laser bias current
          Transmitted optical power
          Received optical power
          Transceiver supply voltage
It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range.
The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. The 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory.
For more detailed information including memory map definitions, please see the XFP MSA Specification.

Regulatory Compliance

Feature	Reference	Performance
Electrostatic discharge(ESD)	IEC/EN 61000-4-2	Compatible with standards
Electromagnetic Interference (EMI)	FCC Part 15 Class B EN 55022 Class B (CISPR 22A)	Compatible with standards
Laser Eye Safety	FDA 21CFR 1040.10, 1040.11 IEC/EN 60825-1,2	Class 1 laser product
Component Recognition	IEC/EN 60950 ,UL	Compatible with standards
ROHS	2002/95/EC	Compatible with standards
EMC	EN61000-3	Compatible with standards

Forward

Related products

Brocade 10g-Sfpp-Bxu-80K Compatible 10gbase-Bx80-U Bidi SFP Fiber 1270nm-Tx/1330nm-Rx 80km Dom Transceiver Module

US$ 5 ~ 128

Extreme Networks 10GB-Bx80-D Compatible 10gbase-Bx80-D Bidi SFP+ 1330nm-Tx/1270nm-Rx 80km Dom Fiber Transceiver Module

US$ 5 ~ 128

10gbase-Bx80-D Bidi SFP+ Port 1330nm-Tx/1270nm-Rx 80km Dom Transceiver Module

US$ 5 ~ 128

Cisco SFP-10g-Bx40d Compatible 10gbase-Bx40-D Bidi SFP+ 1330nm-Tx/1270nm-Rx 40km Dom Transceiver Module

US$ 30 ~ 120

Brocade C49 10g-Sfpp-Zrd-1538.19 Compatible 10g DWDM SFP+ 100GHz 1538.19nm 80km Dom LC SMF Transceiver Module

US$ 3 ~ 150

Juniper Networks Sfpp-10ge-Sr Compatible 10gbase-Sr SFP 10g 850nm 300mtrs Mmf Dom Transceiver Module

US$ 5 ~ 6

Original Factory XFP 10g Bidi Fiber Optic Transceiver Tx15700 Rx1490 10g Dom Duplex LC 80km SMF Transceiver Module Compatible Cisco

US$ 272 ~ 274

Original Factory SFP-10g-Bx60-D Transceiver Tx1330nm Rx1270nm Ddm LC SMF SFP+ 10g Bidi Optical Module 60km Compatible Cisco

US$ 54 ~ 58

Customers Also viewed

10g SFP Bidi 80km1490/1550 Gigabit Single Fiber 10g Transceiver 80km Bidi for Cisco 10g SFP+ Transceiver Module

US$ 450 ~ 550

XFP 10g Bidi Fiber Optic Transceiver Tx15700 Rx1490 10g Dom Duplex LC SMF Transceiver Module 80km

US$ 272 ~ 274

10g SFP Bidi 80km1490/1550 Gigabit Single Fiber 10g Transceiver 80km SFP+ Module

US$ 24 ~ 400

10gbase-Zr XFP 1550nm 80km Dom SFP Transceiver Module

US$ 80 ~ 90

Mrv C50 SFP-10gdwzr-50 Compatible 10g DWDM SFP+ 1537.40nm 80km Dom Transceiver Module

US$ 3 ~ 150

Product Tag:

Related categories:

Optical Module Transceiver Fiber Optical Module SFP Optical Transceiver Fiber Transceiver

Scroll to Top

Categories

Brocade 10g-Sfpp-Bxu-80K Compatible 10gbase-Bx80-U Bidi SFP Fiber 1270nm-Tx/1330nm-Rx 80km Dom Transceiver Module

Connect with us

Categories

Shopping bag