Description
40G QSFP to 10G SFP AOC Active Optical Cable
Introduction:
The TK-2SFP10G-AOC150CM/200CM/250CM is a Two-Channel, Pluggable, Parallel, Fiber-Optic QSFP+ Active Optical Cable (AOC) to 2 x SFP+ Active Optical Cable break-out solution. This Breakout cable is intended for 40G to 2 x 10G applications.
This AOC is a high performance cable for short-range multi-lane data communication and interconnect applications. It integrates four data lanes in each direction with 40 Gbps aggregate bandwidth. Each lane can operate at 10.3125 Gbps. These cables also support 2 x 10G InfiniBand QDR applications and are backwards compatible to the 4 x 5G IB DDR and 4 x 2.5G IB single IB SDR applications.
This AOC incorporates TAKFLY' proven integrated circuit and VCSEL technology to provide reliable long life, high performance, and consistent service.
Features: QSFP+ AOC end:
1. Compliant to the 40GBASE-SR4 and XLPPI
2. Specification per IEEE 802.3ba-2010 and supporting
3. 40G-IB-QDR / 20G-IB-DDR / 10G-IB-SDR applications
4. Compliant to the industry standard SFF-8436
5. Power Level 1: Max Power < 1.5 W
6. Operate at 10.3125 Gbps per channel with 64b/66b
7. Encoded data for 40GbE application and at 10 Gbps with 8b/10b compatible encoded data for 40G-IB-QDR application
Each 2x SFP+ end:
1. Compliant to the electrical specifications per SFF-8431 Specifications for Enhanced Small Form Factor Pluggable Module
2. Mechanical specifications per SFF Committee SFF-8432 Improved Pluggable Form factor "IPF"
3. Maximum power dissipation 0.35W per end.
Active Optical Cable Assembly:
1. 0 to 85 C degree case temperature operating range
2. Proven High Reliability 850 nm technology: VCSEL transmitter and PIN receiver
3. Hot pluggable for ease of servicing and installation
4. Two Wire Serial interface
5. Utilizes optical fiber for high density and thin, lightweight cable managementApplication: 1. 40GbE and 10GbE break-out applications for Datacom switch and router connections
2. 40G to 2xlOG density applications for Datacom and Proprietary protocol applications
3. DatacenterQuality Warranty: 3 yearsActive Cable-End Electrical Characteristics:The following characteristics are defined over the Recommended Operating Conditionsunless otherwise noted. Typical values are for Tc = 40 °C, Vcc = 3.3 V | Parameter | Symbol | Min | Typical | Max | Unit |
| QSFP+ 40G Active Cable-End Power Consumption | | | | 1.5 | W |
QSFP+ 40G Active Cable-End
Power Supply Current | | | | 300 | mA |
SFP+ 10G Active Cable-End
Power Consumption | | | | 0.35 | W |
SFP+ 10G Active Cable-End
Power Supply Current | | | | 100 | mA |
QSFP+ AOC-end Electrical Characteristics Electrical Specifications:| Parameter | Symbol | Min | Typical | Max | Unit |
| Differential input impedance | Zin | 90 | 100 | 110 | ohm |
| Differential Output impedance | Zout | 90 | 100 | 110 | ohm |
| Differential input voltage amplitude | AVin | 300 | | 1100 | mVp-p |
| Differential output voltage amplitude | AVout | 400 | | 800 | mVp-p |
| Bit Error Rate | BR | | | E-12 |
| Input Logic Level High | VIH | 2.0 | | VCC | V |
| Input Logic Level Low | VIL | 0 | | 0.8 | V |
| Output Logic Level High | VOH | VCC-0.5 | | VCC | V |
Output Logic Level Low
| VOL | 0 | | 0.4 | V |
SFP+ AOC-end Electrical Specifications:| Parameter | Symbol | Min | Typical | Max | Unit |
| Differential input impedance | Zin | 90 | 100 | 110 | ohm |
| Differential Output impedance | Zout | 90 | 100 | 110 | ohm |
| Differential input voltage amplitude | AVin | 100 | | 1800 | mVp-p |
| Differential output voltage amplitude | AVout | 400 | | 800 | mVp-p |
| Bit Error Rate | BR | | | E-12 |
| Input Logic Level High | VIH | 2.0 | | VCC | V |
| Input Logic Level Low | VIL | 0 | | 0.8 | V |
Recommended Operating Conditions and Supply Requirements:| Parameter | Symbol | Min | Typical | Max | Unit |
| Operating Case Temperature | TOPC | 0 | | 85 | degC |
| Power Supply Voltage | VCC | 3.13 | 3.3 | 3.47 | V |
| Data Rate | DR | | 10.3 | 11.3 | Gbps |
| Data Speed Tolerance | ADR | -100 | | +100 | ppm |
| Link Distance with OM3 fiber | D | 0 | | 100 | m |
| Control* Input Voltage High | Vih | 2 | | VCC+0.3 | V |
| Control* Input Voltage Low | Vil | -0.3 | | 0.8 | V |
| I2C Serial Interface frequence | fs | | | 400k | Hz |
| Power Supply Noise | | | | 50 | mVpp |
| Receiver Differential Data Output Load | | | | 100 | mVpp |
Certificates:
Any question about this Active Optical Cable, please leave me an inquiry or contact me directly.
Complaint
