Complaint
Distribute gate design traction drive high voltage kp thyristors
High Voltage Phase Control Thyristor SCR
Feature
Design for high power industrial and power transmission applications.
Optimized for low on-state voltage and match Qrr and VT available for series or parallel connections.
We provide one of the most comprehensive ranges of standard phase control thyristor
Application
1,High-power inversion 2,AC and DC motor control 3,AC/DC switching
4,Phase-controlled rectification 5,Active and passive inverter 6,Soft starte
Introduction:
A thyristor/SCR is a solid-state semiconductor device with four layers of alternating P and N-type materials. Some sources define a silicon-controlled rectifier (SCR) and thyristor/SCR as synonymous.
It acts exclusively as a bistable switch, conducting when the gate receives a current trigger and continuing to conduct while the voltage across the device is not reversed (forward-biased). A three-lead thyristor/SCR is designed to control the larger current of its two leads by combining that current with the smaller current of its other lead, known as its control lead. In contrast, a two-lead thyristor/SCR is designed to switch on if the potential difference between its leads is sufficiently large (breakdown voltage).
The first thyristor/SCR devices were released commercially in 1956. Because thyristor/SCRs can control a relatively large amount of power and voltage with a small device, they find wide application in control of electric power, ranging from light dimmers and electric motor speed control to high-voltage direct-current power transmission. thyristor/SCRs may be used in power-switching circuits, relay-replacement circuits, inverter circuits, oscillator circuits, level-detector circuits, chopper circuits, light-dimming circuits, low-cost timer circuits, logic circuits, speed-control circuits, phase-control circuits, etc. Originally, thyristor/SCRs relied only on a current reversal to turn them off, making them difficult to apply for direct current; newer device types can be turned on and off through the control gate signal. The latter is known as a gate turn-off thyristor/SCR, or GTO thyristor/SCR. A thyristor/SCR is not a proportional device like a transistor. In other words, a thyristor/SCR can only be fully on or off, while a transistor can lie in between on and off states. This makes a thyristor/SCR unsuitable as an analog amplifier, but useful as a switch.
Classification:
thyristor/SCR according to the shutoff, conduction and control methods can be divided into ordinary thyristor/SCR (SCR), bidirectional thyristor/SCR (TRIAC), inverse thyristor/SCR (RCT), gate turn off thyristor/SCR (decision), BTG temperature control of thyristor/SCR, thyristor/SCR (TT abroad, TTS domestic) and optically controlled thyristor/SCR (LTT), etc.
The thyristor/SCR can be divided into two polar thyristor/SCR, triode thyristor/SCR, and quadrupole thyristor/SCR according to its pins and polarity.
The thyristor/SCR can be divided into three types: metal packaging thyristor/SCR, plastic sealing thyristor/SCR, and ceramic packaging thyristor/SCR.
Among them, metal packaging thyristor/SCR is divided into a bolt shape, plate shape, round shell, and so on. The laminated thyristor/SCR is divided into two kinds: strip fin and no heat sink.
The thyristor/SCR can be divided into three types: high-power thyristor/SCR, medium power thyristor/SCR, and small power thyristor/SCR according to the current capacity.
In general, the large-power thyristor/SCR adopts a ceramic package, while the medium and small power thyristor/SCR is mostly sealed or metal encapsulated.
thyristor/SCR speed according to the cut-off can be divided into ordinary thyristor/SCR and fast thyristor/SCR, fast thyristor/SCR include all specially designed for rapid application of thyristor/SCR, have regular fast thyristor/SCR and working in a higher frequency of high-frequency thyristor/SCR, respectively applied to 400 Hz and above 10 kHz chopping or inverter circuits.
(note: high frequency does not equal fast thyristor/SCR)
Application:
we are one professional manufacturer and trading company for phase control thyristor and SCR. We are specialized in producing power semiconductors devices. The main products are fast switch thyristor/SCR(KK series)for MF inductor furnace, high voltage phase control thyristor/SCR(KP series) for soft start. And high voltage soft-start components, which the main technical indicators of high-voltage thyristor/SCRs have reached or exceeded those of international famous brand products. The phase control thyristor/SCR(KP series) are widely used in high-power inversion, AC and DC motor control, AC/DC switching,phase-controlled rectification, Active and passive inverter, soft starter
The fast switch thyristor/SCR(KK series)are widely used in inverters, chopper, inductive heating, Various types of forced converters, electric welding
the company's products have been sold nationwide and exported to Europe, Middle East, Southeast Asia, South Africa, and other countries and regions.
Factory
Phase Control Thyristor
Introduction:
Phase control thyristor is a low loss switch semiconductor device.It has a wide voltage range,from 1000V-8000V,Current range 100A-5000A.As a high power electronic component, it plays a very important role in the industry.
We design and manufacture various shapes of phase control thyristor. Our phase-controlled thyristor includes disc thyristor and stud thyristor. Disc phase control thyristor current range from 500A to 6000A, voltage range from 1000V to 7500V.Stud thyristor maximum current 500A, Maximum voltage 2500V.
Our phase control thyristor has a very good low switching loss characteristic, it is popular be used on turn on and off equipment. For example, our medium voltage phase control thyristor(6500V thyristor) is popularly used on medium voltage soft starter, AC motor drives, and high power converter, etc. The low voltage thyristor(1600V-2800V) are popularly used on low power soft starter, AC drives.
With stable performance, our phase control thyristor also hot used on induction heating furnace. It is always used on a rectifier circuit of the furnace. Besides, our high power thyristor also used on traction and transmission, excitation, static var compensator(SVC), high current rectifier, high power supply, etc.
Certificate:
Phase Control Thyristor Features:
Design for high power industrial and power transmission applications.
Optimized for low on-state voltage and match Qrr and VT available for series or parallel connections.
6500V thyristor special used for MSS high voltage
We provide one of the most comprehensive ranges of standard phase control thyristor/SCR
Soft start module and static var compensator (SVC)
Phase Control Thyristor Applications:
1, Low voltage soft starter, medium voltage soft starter
2, Industrial drives, Inverter, Converters
3, Traction and transmission, High current power supply
4, Excitation
5, Static var compensator (SVC)
Packing:
Datasheet for Code Selection
| Capsule | ||||||||||
| Part No. | IT(AV) | VDRM | ITSM | I2 t | VTO | rT | RthJC | RthCH | F | Outline |
| Tc=70ºC | VRRM | 50HZ TVJM | 50HZ TVJM | TVJM | TVJM | |||||
| A | V | A | A2S.103 | V | mΩ | ºC/W | ºC/W | KN | ||
| Up to 1200V | ||||||||||
| KP400/06-12 | 400 | 600-1200 | 6300 | 198 | 0.90 | 0.650 | 0.085 | 0.020 | 6 | T6 |
| KP600/06-12 | 600 | 600-1200 | 9200 | 423 | 0.93 | 0.600 | 0.045 | 0.010 | 9 | T7 |
| KP800/06-12 | 800 | 600-1200 | 11000 | 605 | 0.85 | 0.500 | 0.040 | 0.010 | 12 | T9 |
| KP1000/06-12 | 1000 | 600-1200 | 12500 | 781 | 0.83 | 0.350 | 0.035 | 0.008 | 16 | T9 |
| KP1800/06-12 | 1800 | 600-1200 | 27000 | 3645 | 0.85 | 0.180 | 0.020 | 0.006 | 25 | T11 |
| KP2000/06-12 | 2000 | 600-1200 | 31000 | 4805 | 0.83 | 0.150 | 0.018 | 0.006 | 32 | T12 |
| KP2600/06-12 | 2600 | 600-1200 | 45000 | 10125 | 0.85 | 0.130 | 0.013 | 0.005 | 45 | T13 |
| KP3800/06-12 | 3800 | 600-1200 | 62000 | 19220 | 0.80 | 0.050 | 0.011 | 0.003 | 55 | T15 |
| Up to 2000V | ||||||||||
| KP300/12-20 | 300 | 1200-1800 | 5000 | 125 | 0.95 | 1.200 | 0.085 | 0.020 | 6 | T6 |
| KP600/12-20 | 600 | 1200-1800 | 8200 | 336 | 1.00 | 0.600 | 0.045 | 0.010 | 9 | T7 |
| KP800/12-20 | 800 | 1200-1800 | 14000 | 980 | 0.95 | 0.350 | 0.035 | 0.008 | 16 | T9 |
| KP1000/12-20 | 1000 | 1200-1800 | 17000 | 1445 | 0.93 | 0.300 | 0.030 | 0.008 | 20 | T10 |
| KP1500/12-20 | 1500 | 1200-1800 | 24600 | 3026 | 0.92 | 0.230 | 0.020 | 0.006 | 25 | T11 |
| KP1800/12-18 | 1800 | 1200-1800 | 27500 | 3781 | 0.90 | 0.200 | 0.018 | 0.006 | 32 | T12 |
| KP2500/12-18 | 2500 | 1200-1800 | 45000 | 10125 | 0.85 | 0.130 | 0.013 | 0.005 | 45 | T13 |
| Part No. | IT(AV) | VDRM | ITSM | I2 t | VTO | rT | RthJC | RthCH | F | Outline |
| Tc=70ºC | VRRM | 50HZ TVJM | 50HZ TVJM | TVJM | TVJM | |||||
| A | V | A | A2S.103 | V | mΩ | ºC/W | ºC/W | KN | ||
| KP3000/12-18 | 3000 | 1200-1800 | 54000 | 14580 | 0.90 | 0.070 | 0.011 | 0.002 | 55 | T15 |
| KP4000/12-18 | 4000 | 1200-1800 | 60000 | 18000 | 0.88 | 0.070 | 0.009 | 0.002 | 70 | T16 |
| KP5000/12-18 | 5000 | 1200-1800 | 80000 | 32000 | 0.88 | 0.065 | 0.007 | 0.001 | 90 | T17 |
| Up to2500 V | ||||||||||
| KP500/20-25 | 500 | 2000-2500 | 7500 | 281 | 0.95 | 1.100 | 0.045 | 0.010 | 9 | T7 |
| KP700/20-25 | 700 | 2000-2500 | 10000 | 500 | 1.00 | 0.720 | 0.035 | 0.008 | 16 | T9 |
| KP900/20-25 | 900 | 2000-2500 | 12800 | 819 | 0.95 | 0.500 | 0.030 | 0.008 | 20 | T10 |
| KP1300/20-25 | 1300 | 2000-2500 | 21000 | 2205 | 0.90 | 0.300 | 0.020 | 0.006 | 25 | T11 |
| KP1600/20-25 | 1600 | 2000-2500 | 25000 | 3125 | 0.95 | 0.260 | 0.018 | 0.006 | 32 | T12 |
| KP2000/20-25 | 2000 | 2000-2500 | 33000 | 5445 | 0.97 | 0.200 | 0.013 | 0.005 | 45 | T13 |
| KP2500/20-25 | 2500 | 2000-2500 | 41600 | 8653 | 0.90 | 0.150 | 0.011 | 0.002 | 55 | T15 |
| KP3200/20-25 | 3200 | 2000-2500 | 48000 | 11520 | 0.87 | 0.130 | 0.009 | 0.002 | 70 | T16 |
| KP4000/20-25 | 4000 | 2000-2500 | 74500 | 27751 | 1.00 | 0.100 | 0.007 | 0.001 | 90 | T17 |
| Up to3500 V | ||||||||||
| KP400/25-35 | 400 | 2500-3500 | 6100 | 186 | 1.10 | 1.750 | 0.045 | 0.010 | 9 | T7 |
| KP600/30-35 | 600 | 3000-3500 | 8300 | 344 | 1.05 | 1.000 | 0.035 | 0.008 | 16 | T9 |
| KP700/25-30 | 700 | 2500-3000 | 10000 | 500 | 1.00 | 0.700 | 0.035 | 0.008 | 16 | T9 |
| KP800/25-35 | 800 | 2500-3500 | 11500 | 661 | 1.00 | 0.750 | 0.030 | 0.008 | 20 | T10 |
| KP1200/25-30 | 1200 | 2500-3000 | 22000 | 2420 | 0.95 | 0.400 | 0.020 | 0.006 | 25 | T11 |
| KP1000/30-35 | 1000 | 3000-3500 | 17000 | 1445 | 1.10 | 0.600 | 0.020 | 0.006 | 25 | T11 |
| KP1200/25-35 | 1200 | 3000-3500 | 19000 | 1805 | 1.10 | 0.500 | 0.018 | 0.006 | 32 | T12 |
| KP1800/25-30 | 1800 | 2500-3000 | 29000 | 4205 | 1.05 | 0.300 | 0.013 | 0.005 | 45 | T13 |
| KP1600/30-35 | 1600 | 3000-3500 | 28000 | 3920 | 1.05 | 0.400 | 0.013 | 0.005 | 45 | T13 |
| KP2200/25-35 | 2200 | 2500-3500 | 31000 | 4805 | 1.03 | 0.250 | 0.011 | 0.002 | 55 | T15 |
| KP3000/25-35 | 3000 | 2500-3500 | 40000 | 8000 | 0.85 | 0.180 | 0.009 | 0.002 | 70 | T16 |
| KP3500/25-35 | 3500 | 2500-3500 | 72000 | 25920 | 1.00 | 0.150 | 0.007 | 0.001 | 90 | T17 |
| Up to4500 V | ||||||||||
| KP500/35-45 | 500 | 3500-4500 | 7000 | 245 | 1.20 | 1.600 | 0.035 | 0.008 | 16 | T9 |
| KP900/35-45 | 900 | 3500-4500 | 14500 | 1051 | 1.20 | 0.900 | 0.020 | 0.006 | 25 | T11 |
| KP1000/35-45 | 1000 | 3500-4500 | 15000 | 1125 | 1.18 | 0.800 | 0.018 | 0.005 | 32 | T12 |
| KP1500/35-45 | 1500 | 3500-4500 | 25000 | 3125 | 1.15 | 0.500 | 0.013 | 0.005 | 45 | T13 |
| KP1800/35-45 | 1800 | 3500-4500 | 25000 | 3125 | 1.15 | 0.350 | 0.012 | 0.004 | 50 | T14 |
| KP2000/35-45 | 2000 | 3500-4500 | 27000 | 3645 | 1.05 | 0.330 | 0.011 | 0.002 | 55 | T15 |
| KP2500/35-45 | 2500 | 3500-4500 | 32500 | 5281 | 1.25 | 0.230 | 0.009 | 0.002 | 70 | T16 |
| KP3000/35-45 | 3000 | 3500-4500 | 45000 | 10125 | 1.10 | 0.200 | 0.007 | 0.002 | 90 | T17 |
| Part No. | IT(AV) | VDSM | VDRM | ITSM | VTO | rT | RthJC | RthCH | F | Outline |
| Tc=70ºC | VRSM | VRRM | 50HZ TVJM | TVJM | TVJM | |||||
| A | V | V | A | V | mΩ | ºC/W | ºC/W | KN | ||
| Up to5200 V | ||||||||||
| KP400/45-52 | 400 | 4500-5200 | 4200-4600 | 5400 | 1.30 | 1.900 | 0.045 | 0.008 | 16 | T9 |
| KP800/45-52 | 800 | 4500-5500 | 4200-4600 | 12000 | 1.15 | 1.000 | 0.022 | 0.006 | 25 | T11 |
| KP1200/45-52 | 1200 | 4500-5200 | 4200-4600 | 19000 | 1.15 | 0.600 | 0.015 | 0.005 | 32 | T13 |
| KP1500/45-52 | 1500 | 4500-5200 | 4200-4600 | 25000 | 1.20 | 0.550 | 0.011 | 0.002 | 55 | T15 |
| KP2200/45-52 | 2200 | 4500-5200 | 4200-4600 | 45000 | 1.10 | 0.350 | 0.009 | 0.002 | 70 | T16 |
| KP2800/45-52 | 2800 | 4500-5200 | 4200-4600 | 55000 | 1.05 | 0.250 | 0.007 | 0.002 | 90 | T17 |
| Up to6500 V | ||||||||||
| KP300/55-65 | 350 | 5500-6500 | 4500-5600 | 4500 | 1.20 | 2.600 | 0.045 | 0.008 | 16 | T9 |
| KP700/55-65 | 750 | 5500-6500 | 4500-5600 | 11000 | 1.20 | 1.100 | 0.022 | 0.005 | 25 | T11 |
| KP1000/55-65 | 1100 | 5500-6500 | 4500-5600 | 14300 | 1.18 | 0.800 | 0.015 | 0.004 | 32 | T13 |
| KP1200/55-65 | 1200 | 5500-6500 | 4500-5600 | 22000 | 1.15 | 0.700 | 0.011 | 0.002 | 55 | T15 |
| KP1800/55-65 | 1800 | 5500-6500 | 4500-5600 | 31000 | 1.25 | 0.500 | 0.009 | 0.002 | 70 | T16 |
| KP2500/55-65 | 2500 | 5500-6500 | 4500-5600 | 43000 | 1.20 | 0.330 | 0.007 | 0.002 | 90 | T17 |
| TVJM=125ºC If need 35mm please note outline H code H:35mm | ||||||||||
Outline size:
