Industrial Single Stage End Suction Centrifugal Water Pump for Municipal Water Supply and Drainage

Min.Order: 1
Product origin: Xiangtan, Hunan, China
Infringement complaint: complaintComplaint
US$ 1000 ~ 10000

Description
Overview
Type NDX pump is applicable for pumping clean water and liquids whose physical and chemical properties are similar to water and without solid particles.
This series of products can be used in factories,mines,urban water supply and drainage,HAVC,industrial softened water and farmland irrigation and drainage,etc.It can also be used in pressure stabilization and water supply systems of urban fire control.
Pump with the same specification can change the performance parameters by cutting the outer diameter of the impeller;the normal speed of the pump is 1450RPM and 2900RPM, if it is required to operate at the maximum speed of 3550RPM(60Hz power supply or with gasoline and diesel engine),our company can provide technical instruction on the change of the outer diameter of the impeller
The type NDX pump features simple structure,reliable performance,small volume,light weight,high efficiency,good ati-cavitation performance, low power consumption and convenient use and maintenance
The pump is suitable for pumping medium at temperature of -10~85ºC and working pressure of 1.0MPa,if there is a need to increase to 1.6MPa or higher,please specify when selecting and ordering

Performance Parameters
ModelCapacity(m³/h)Head(m)Pump efficiency (%)Shaft power (kW)Speed(rpm)Impeller outer diameter(mm)Inlet caliber(mm)Onlet caliber(mm)Motor Power(kW)Weight(kg)
NDX80-65-16064.839.56710.412900174806518.5kW43
1083580.212.84
129.6328113.95

Table Product Attribute
AttributeAttributeAttribute value
MaterialImpellerHT250
Pump bodyHT250
Pump shaft2Cr13
SuspensionHT250
Seal ringHT250
Machinery SealVulcan
CouplingElastic pin
Antifriction bearingNSK
Working conditionsMedium temperature(ºC)≤85ºC
Ambient temperature(ºC)40
Design pressure(MPa)1.6
InstallationInlet diameter(mm)80
outlet diameter(mm)65
Direction of rotationViewed from the transmission end, rotate clockwise
Entrance orientationAxial suction
Exit orientationVertical up
MotorNumber of motor phases3
Motor power safety factor1.2
Protection classIP54
Insulation classF
Motor power(kW)18.5kW
Motor modelYE2-160L-2
Power frequency(Hz)50
Energy efficiency ratingIE3
PackageWeight(kg)43

Product Features
Energy efficient: Applying the most advanced NRCE design software and CFD fluid simulation software to develop and design the high efficiency hydraulic model,through the analysis of pump flow field,temperature field and strength,thermal deformation,fracture,rotor dynamics,etc,to achieve high efficiency ,reliability and wide efficiency zone,we have made the pump satisfy the efficiency and reliability requirements of centrifugal pump operating under design conditions and non-design conditions, reaching the international advanced level.
Rear opening type structure:The maintenance is convenient,It is not necessary to disassemble the suction and discharge pipes during maintenance to pull out the rotor parts for maintenance
Quality assurance:Before casting,the imported chemical analysis of the materials was carried out by the direct reading spectrum analyzer introduced from Britain to ensure that the material composition meets the requirement.The pump impeller and rotor components are tested by precise dynamic balance test,so the pump can run more smoothly, have less vibration and noise and longer service life.
Product orientation:Improve the technical level of the domestic equipment industry, effectively serve equipment and processes to meet the needs of safety,reliability,energy conservation and environmental Protection.

Structural Features
Pump casing:Footing support structures,base support structure.The pump intakes axially and discharges from the top end.The spiral volute can bear up to 2.5Mpa of pressure.The flanges at the inlet and outlet can be drilled according to the metric system or the American system
Impeller:The closed impeller adopts excellent hydraulic model design to ensure the performance and efficiency of the pump.The impellers are 100% tested by dynamic balance test to reduce the vibration of the pump
Pump shaft:The pump is equipped with SS420 stainless steel shaft,which has wide versatility.There are more than 60 specifications in the whole series,while only six kinds of shafts are used.The same specifications of shafts,bearding,shaft sleeves,shaft seals and impeller fasteners can be interchanged
Shaft seal:It adopts high quality mechanical seals from well know domestic manufactures,the seals have long service life and no leakage,and can be equipped with auxiliary systems such as flushing and cooling
Bearing:It is imported NSK bearing that ensure a longer service life.The double closed,maintenance free bearding eliminates the need for separate lubricants,saving the time for maintenance.



FAQ
1. Q:Are you a manufacturer or trading company  
A:We are a manufacturer that specializes in industrial pump for 60 years
 
2. Q:What payment term do you prefer?
 A:Normally we take payment term 30% T/T in advance,70% paid before shipment, we can also accept L/C at sight.
 
3. Q:What about the package?
A:Standard export plywood case
 
4. Q:How long is the warranty?
A: Eighteen (18) months after delivery, twelve (12) Months from the date of commissioning, whichever comes earlier
 
5. Q:Is it acceptable to make customer's own brand?
 A: Sure, we can do OEM & ODM
 
6. Q:How many days does it take for manufacturing?
 A: It depends on order quantity and pump types. Normally it takes 20-120 days

Product Tag:
Related categories:
Scroll to Top