Complaint
Industry Temperature Humidity Environment Stability Climate Test Chamber, used for material performance test under different environment, such as heat, cold, moisture, heat and moisture, mainly applied in electronics, electrical appliances, mobile, communications, instruments, vehicles, plastic products, metals, food, chemicals, building materials, medical, aerospace and other industries.
*The test requirements that need to reach below -40 degrees will use a cascade double compression refrigeration system. When the test is above -20 degrees, only one compressor will be started to work with a smaller power heating tube for inching heating, which saves electricity and water; ( If single-stage refrigeration is used, the compressor will be equipped with high-power full-process refrigeration, and the refrigeration capacity is also large, and a higher-performance heating tube is required to balance, so it consumes electricity and water.
*The sink is made of special materials with low thermal conductivity and no water droplets on the surface (such as metal materials will form water droplets on the surface, which will easily wet the sample and affect the test results), and is equipped with a diversion device. If the sink appears When the internal pressure is too high or the water level is too high, it will flow into the humidification barrel through the diversion hole.
*The cascade dual-compression refrigeration system can easily meet the test requirements of low temperature -40 degrees and below. When the single-stage refrigeration reaches -38 degrees, it will be difficult to drop to -40 degrees. This is due to the characteristics of R404A refrigerant. It can only be achieved by temperature compensation.
*The machine is exquisite, the internal space is large, the external dimension is small, the width is only about 78cm, and the single-door laboratory can be easily entered.
*There is a pressure relief hole on the top.
| Model | PW-CTH100 | PW-CTH-150 | PW-CTH-225 | PW-CTH-408 | PW-CTH-800 | PW-CTH-1000 |
| Inner chamber size W×H×D(cm) | 50×50×40 | 50×60×50 | 60×75×50 | 80×85×60 | 100×100×80 | 100×100×100 |
| Exterior chamber size W×H×D(cm) | 78×157×105 | 78×167×115 | 88×185×115 | 108×195×125 | 128×210×145 | 128×210×165 |
| Testing temperature range | 0ºC,-20ºC,-40ºC,-70ºC~150ºC | |||||
| Testing humidity range | 20%RH~98%RH | |||||
| Temp.humi.fluctuation | ±0.3ºC;±0.5%RH | |||||
| Temp.humi.uniformity | ±2ºC;±3% empty loading after stablize for 30mins ±2ºC;±3%RH | |||||
| Temp.humi.resolution | 0.01ºC;0.1%RH | |||||
| Heating&cooling time ºC/min | Heat-up:3ºC/min(average),cool-down:1ºC/min(average) | |||||
| Exterior chamber material | Cold rolled plate + Powder coating | |||||
| Interior chamber material | SUS#304 Stainless steel | |||||
| Insulation material | Rigid Polyurethane foam | |||||
| Circulation system | Centrifugal fan air circulation system | |||||
| Heating system | SUS# Stainless steel high-speed heater | |||||
| Humidification system | Electrothermal steam humidification | |||||
| Dehumidifying | ADP critical dew point cooling / dehumidifying method | |||||
| Refrigeration system | Finned evaporator + Air(Water) cooling condenser | |||||
| Controlling system | Touch screen controller | |||||
| Other components | Vacuum glass observation window | |||||
| Test hole(100mm) | ||||||
| Controller status indicator | ||||||
| View light | ||||||
| Compartment shelf (2 freely adjustable) | ||||||
| Safety protection device | Overheat protection circuit breaker | |||||
| Humidification system overheat protection | ||||||
| Compressor overload protection | ||||||
| Control system overload protection | ||||||
| overload indicator | ||||||
| Phase sequence protection | ||||||
| Water shortage protection | ||||||
| High voltage and low voltage protection | ||||||
| Over temperature protection | ||||||
| Water supply delay protection | ||||||
| Fan overcurrent protection | ||||||
| Power supply | AC 1ψ220V;3ψ380V 60/50Hz | |||||
| Customization service | Non-standard or special requirements are all welcome | |||||
Company Introduction:
PW (Guangdong) Instruments Co., Ltd. was established in March 2007, a national high-tech enterprise, located in Tongzheng Intelligent Industrial Park, No. 2, North 3rd Road, Tingshan Square, Houjie Town, Dongguan City, Guangdong Province. Through years of operation, the company has gathered a group of talents with considerable qualifications in the industry, and has accumulated a large number of high-quality customers. In order to better serve customers in East China, the company established PW Instruments (Shanghai) Co., Ltd. in Shanghai and set up an instrument exhibition hall and testing center in Suzhou Industrial Park.
Corporate Culture:
Vision: Become a world-renowned instrument manufacturer
Mission: Provide customers with high-quality testing equipment
Values: Customer satisfaction is our aim.
Q: Are your company a trading one or a factory?
A: Factory, More than 15 years focusing on test equipment field, 10 years exporting experience.
Q: After an order is placed, when to deliver?
A: Generally about 10-25 days, If we have inventory, we can arrange shipment within 3 days.
Please be aware that our production lead times depend on specific items and item quantities.
Q: What about the warranty with after-sales services?
A: The testing machine is guaranteed for 12 months by PW, we can help you to repair your problem controller freely, even it's not from our factory. After the warranty, the professional after-sale service team will provide perfect technical support and help guests solve problems encountered while using our product, handle guest problems and complaints in a professional and timely.
Q: What about the product's services and quality?
A: Each piece of equipment must be carried out 100% quality examination and test when shipping and delivering goods. Product use training, each of our products provides video training to show you how to install & operate. We can arrange engineer to train the operation of equipment to customer's company when you need. products are widely recognized and trusted by users.
A: Considerate Service Different countries plugs, manually change the voltage from 110V to 220V, insurance indicator.
Q: Can your products be customized?
A: Yes, our product can be customized according to your parameters.
