Economical DPF Purging and Testing Equipment/DPF Ash Clean Machine Filtr Particul Diesel Regeneration Chamber Steel Intelligent Removal Thermal Regenerat

Min.Order: 1
Product origin: Wuxi, Jiangsu, China
Infringement complaint: complaintComplaint
US$ -1

Description
Product introduction
Product NameElectric heating type DPF high temperature regeneration equipment
Main technical parameters
ModelKL-DZL15KL-DZL40
Power15 kW35 kW
Heating rate 30ºC/min44ºC/min
The chamber size500×550×700mm800×800×700mm
Boundary dimension1050×850×1880mm1350×1100×1880mm
The substrate capacitySingle loading of a diameter of 330mm or
Two DPF carriers with 190mm diameter substrate
A single loading of four diameters of 330mm or
Six DPF carriers with 190mm diameter substrate
Power supplyThree-phase five-line system,380V,50Hz
Temperature rangeNormal temperature~750 ºC
Temperature control tolerance±5ºC
Electric control systemTemperature control module,7-inch all-piece touch display
Fresh air systemFresh air fan supplies oxygen and cooling, and automatically controls the intake volume
 
Product NameElectric heating type DPF high temperature regeneration equipment
ModelKL-DZL25
The chamber size500×550×700mm (can meet the package φ 450 outer diameter, length ≤450mm) 
Power/air source380v power supply;  Air source pressure: 0.6 ~ 0.8mpa, air consumption ≤30L, intake interface for φ 12 quick connector 
Temperature rangeNormal temperature ~ 620ºC, maximum temperature 650ºC
Heating power24KW, heating rate: 28ºC/min
Stages of temperature controlSet three stage temperature, reach the set value for automatic constant temperature.  Temperature control tolerance: set temperature ±10ºC 
DPF coolingFor high temperature DPF cooling, two butterfly valves, inlet and exhaust, are used to open and inhale cold air and discharge hot air for cooling and cooling after the end of insulation 
Motor powerHigh temperature resistant 0.37KW three-phase motor, flow 1100m3/h
Surface treatmentSurface paint treatment
Door quantitySingle door, each side of the door is installed with high strength hinge, strong jacking force, easy to operate. 
Insulation material128kg/m3 high density aluminum silicate thermal insulation cotton, with flame retardant, heat insulation and good thermal insulation performance 
ProtectorLeakage protection, lack of phase protection, motor overcurrent protection, overtemperature heating protection
 
Product nameStandard DPF purging and testing equipment
ModelKL-DCJ30
Main technical parameters
Power supply220V,50Hz
FanMaximum air volume:1060m3/h;maximum vacuum:5kPa
Boundary dimension1100×800×1880mm
Blow controlOverall pulse purge, PLC automatic control, purge at the same time, vacuum dust collection
Weighing detectionWeighing table range 30Kg,Weigh accuracy: ± 1g; the data can be recorded
Back pressure detectionPLC controls automatic detection and data can be displayed and recorded
Light detectionA 150w high-brightness LED light source, optical flux: 15,000 lumens
Grey collecting deviceVacuum suction, 5 micron level can be cleaned, replacement of the filter element, drawer type dust collection room
Gas storage tank capacityUsing 30L air storage tank, no need for manual intervention pressure regulation, automatic program control purge 
Electric control systemA 7-inch integrated touch display screen, with PLC programming control
protectorLeakage protection, phase absence protection, motor overprotection
Surface treatmentElectrostatic powder baking paint
 
Product nameFuel heating type DPF high temperature regeneration equipment
Serial numberProject UnitParameter
1Model-KL-DZT30
2Rated heating powerkW30
3Maximum quantity of windm3/min4
4Maximum wind pressurekPa30
5Temperature control accuracyºC±20
6Service voltageVSingle-phase AC220
7Power loadkW2.2
8Fuel tankageL10
9Boundary dimensionmm1370x690x1210
10Net weightkg200



RFQ
Q:What are your main products?
A:Our main products are diesel engine exhaust after-treatment system(SCR system, DPF system etc.), and parts(Urea Pump,Urea Nozzle,Catalyst Converter, Sensor etc.)  

Q:Do you have after-sale service?
A:"Customer first" is the core principle followed by our company, and it is also the super criteria adhered by our after-sales service staff. We  have established comprehensive after-sales service network. With headquarter in Wuxi, we have branch offices  Shanghai, Beijing, Changchun, Zhengzhou, Guangzhou, Changsha, Xuzhou and authorized service center throughout the country. We also provide 24 hours free hotline for customerswith premium quality and efficient after-sales service.

Q:I wonder if you can provide free samples?
A:Whether the sample is free depends on the content of the sample and can be decided after discussion.


Q:What product certifications do you have?
A:ISO9001, CE, E-Mark, RoHS And TS16949

Q:What is the delivery time of your product?
A:Generally, it is about 1 month. The delivery time depends on the quantity of the order.  
Product Tag:
Related categories:
Scroll to Top