Description
Product Description
TDP SINGLE TABLET PRESS MACHINE
TDP-5 single punch tablet press machine ,which could press the power material to tablet ,could be widely used in the pharmacy factory ,chemistry factory ,hospital and R & D bureau. This machine is with good performance ,strong suitability ,simple operation ,easily repair ,small cubage ,light .Even under the conditions or power cut ,hand swing is available .Compare to original TDP model press machine ,it is enlarged the machine intensive and engine power with bigger strength .In the meantime enlarge the filling depth ,hence to expand the specification range of tablet .Therefore this machine can meet the demand of different kinds of Chinese traditional medicine and Western medicine and other similar product's requirement .It's deeply welcomed by our customers in different field.
1. This machine is an undersized desktop stamping tablet machine which is driven by
electrical motor, which can stamp out all kinds of tablets continuously.
2. This machine can stamp all kinds of granules and coarse powder into round or
special-formed tablets, which are indicated for labs or for producing in small
quantities all kinds of tablets, pastilles, calcium, special-formed tablets etc.
3. This machine is not indicated for stamping large-granule solid, wet or
micro-powder.
4. The simple structure, convenient operation and high automation make this machine
suitable for stamping all forms of tablets
Product Parameters
Main Technical Data:
| No. | Item | TDP-1.5 | TDP-5 | TDP-6 |
| 1 | Max .press strength(KN) | 15 | 50 | 60 |
| 2 | Max .tablet diameter(mm) | 12 | 20 | 25 |
| 3 | Max .filling depth(mm) | 12 | 18 | 16 |
| 4 | Productive capacity(Pcs/Hour) | 4700 | 4500 | 4000 |
| 5 | Motor power(kw) | 0.25 | 0.55 | 1.1 |
| 6 | Turning speed(r/min) | 1400 | 1400 | 1400 |
| 7 | Weight (kg) | 65 | 125 | 150 |
| 8 | Length*Width*Height(mm) | 570x380x630 | 650x440x650 | 700x500x900 |
Installment and connection of the press machine
Press-tablet machine should be installed on the wood worktable (as well on the
cement table). Use 4 units of M12 bolts to fix it .The high from the worktable
surface to ground is around 600mm(consider easily to the operation) . To
convenient to disassembly and repair., there should be a hole the diameter around
35mm counter to the bottom of pressure rod.To insure the safety ,connecting ground wire before connecting the power ,and
Then remove the triangle belt ,to rolling direction of the operation .(The rotary
Direction should be opposed to the arrow direction on the shield or hand wheel.)
If the rotary direction were incorrect ,it would connect the line additionally ,and
The install the triangle belt.
IV, Assemble and unassembled of the die and adjustment during the operationAssemble of the die
- Assemble the down rush
- Unscrew the fixed bolt ,turn the hand wheel to raise the central rod to the top location and insert the undershoot rod to the hole of the down central rod.(Attention the gap level the gap level aim at the bottom tighten bolt) At last screw the down rush fixed bolt.
- Assemble up rush
Unscrew the fixed bolt ,turn the to up rush rod to the upper hole ,use spanner to lock the upper bolt and screw the fixed bolt.1.Fix the intermediate mould
Unscrew the fixed bolt ,and put the mould into the hole of mould plate ,in the
Meantime insert the rod into the hole .Push it to the bottom of the hole and then
Screw the bolt .level the intermediate mould and avoid locking in the plate to
damage the orifice.2.Turn the hand wheel ,let up rush rod slowly drop to orifice .and observe whether
there is collision or friction ,and then unscrew the fixed bolts (2) of the fixed
plate ,adjust the fixed location of the intermediate mould plate .Let the up rush rod
into the orifice of intermediate mould ,and the adjust it till no collision or no
friction it can be called qualified installment..3.The adjustment of the tablet out
Turn the hand wheel to raise the down rush rod to the top point ,observe whether the surface of down rush rod and intermediate mould are on the same level ,if No. unscrew bolt and press plate of gear ,make the surface of down rush rod and intermediate .Next step ,turn hand wheel and make the empty machine run for several circle .If it goes well ,and then you can press some material to try press and continue to adjustment for next step.4.Adjustment of filling depth (that's the adjustment for the weight of
tablet) .Unscrew the bolt and loose the gear press plate ,left turning the down
adjustable gear to raise the down rush rod ,that's reduce the filling depth (lessen
the weight of tablet). After adjustment should to install the gear press plate and
screw bolt.5.Pressure adjustment (That's adjustment of hardness of tablet).
Loosen the locked nut and turn up rush rod ,left turning rush rod to move down and then pressure increased ,the hardness of the tablet would be increased .On the contrary ,right turning would decrease the pressure and lower the hardness of the tablet .After adjustment use the spanner to lock the bottom of the up rush and screw the nut..
Till now ,the adjustment of the die is basically completed ,restart the machine for trial press several tablets to check the weight of the tablet ,hardness and surface etc quality issues .if it's qualified ,you can put into production .During the production ,you can check the quality of the tablet anytime and adjust it immediately.A.Disassembly of the die.
B.Disassembly of the up rush rod.
Unscrew the fixed nut and pull out the up rush rod .If it's combined very
tight ,you can use clamp to pull it out ,but attention to protect the tip of rod.C.Disassembly of the intermediate mould.
Unscrew the fixed bolt of the intermediate mould and the fixed bolt of down
Rush Rod .unscrew the bolt and loosen the gear press plate .Turning adjustable
gear to raise the down rush rod and take the intermediate mould out .if the
intermediate mould assembled very tight ,so you cannot force turning the hand
wheel to protect the parts .At this time you should disassemble the intermediate
plate and take the mould out.D.Disassembly of down rush rod
Unscrew the fixed bolt of down rush rod .and the turning hand wheel to raise the down rush rod to the top point ,you can pull the down rush rod out ,If it's combined very tight ,you can use the clamp to pull it out .(attention to protect the tip of the rod.) E.After disassembly of the die ,it's still necessary to adjust the gears .Lower the
Down rush rod around 10 mm ,turn the hand wheel to raise the down rush rod
to the highest point ,no higher than the bottom of the intermediate mould (This
step cannot be ignored, avoiding collision between down rush rod and
intermediate mould for next time.) At last screw the fixed bolt of down rush
rod. Detailed Photos
1. Tablet pusher: Made of 304 stainless steel and polished smooth to ensure that the tablets are not damaged during the process of being pushed out
2. Tablet outlet: With a good angle, the tablet can fall smoothly without any phenomenon of tablet accumulation
3. Mold: Our mold has a high degree of closure and precision, and the tablets are made very smoothly without any jamming or fragmentation
4. Motor: Imported copper shaft motor is used, with a long service life and excellent quality, meeting the needs of environmental protection
Certifications
Our certificates and transaction records
We have rich export experience and enjoy global customers
Packaging & Shipping
We use thickened double export wooden cases to ensure the safety of the machine We provide ex factory packing videos to ensure the integrity of the machine. In terms of transportation, our freight forwarder can ensure the safety and timeliness of transportation. We can also accept all transportation modes designated by customers for export. Over the past 15 years, our business proficiency can solve all customers' problems and ensure that our customers can get the goods smoothly and quickly.
Company Profile
Dandong Flight Pharmaceutical Machinery Co., Ltd. is located in Dandong Donggang City, a top 100 County in China. It is a member of China Pharmaceutical Equipment Association and has passed ISO9001:2000 certification. The head office Shanghai Flight Pharmaceutical Machinery Co., Ltd., founded in 1999, is an earlier manufacturer of pharmaceutical production lines in China.
The company is based on the enterprise concept of "integrity and friendship", establishes its business in good faith and wins the world with courtesy. Achieve higher quality, better service and lower price. We have advanced technology to produce first-class pharmaceutical equipment. It mainly focuses on the production of tablet press, filling line, packaging line and various small and medium-sized equipment. Over the years, we have continuously improved and innovated, reached cooperation with nearly 100 manufacturers and customers at home and abroad, and welcome customers at home and abroad to exchange technology with us.
We provide free technical guidance to them, so as to make common progress with the times! With first-class quality, first-class service, first-class reputation and first-class products, the company creates high-quality products in China and builds a bridge of friendship. The company sincerely hopes to work with friends in the industry to improve the technical level of domestic pharmaceutical technology.
Our company's technology
Our workshops were modernized, and equipped with high precision processing facilities such as vertical and horizontal machining centers, digital CNC gantry milling machine and NC lathes, etc.
After Sales Service
Price Term:
1.FCA Shanghai T/T payment
2.Payment Terms: 50%TT before production +50%TT before delivery
3.Lead Time: 3-21 working days after receipt of prepayment and samples
4. Package: in wooden box, confirm to international transportation standard.
5.Technical Standard: Confirm to GMP and relative international regulation.
6.Warranty: The supplier provides 12 months free warranty since the date that the product
was adjusted and qualified, and there is no artificial destruction in this period. Supplier
provides lifetime service support.
7.Installation, Adjustment and Training
The seller provides instrument and video about how to install, adjust and use the machine as
soon as the machine is ready. The seller provides on-time service when user have use problem.
The seller can dispatch one engineer to the buyer's factory for installation and commissioning
and training, the buyer should be responsible for the room and board and the go-back air tickets and visa fee.
FAQ
Q: What about your pharmaceutical machine quality?
A: Our factory has more than 10 years experience in mechanical processing; all our machines already get IS09001, SGS certificate, CE certificate; already exported into many countries and areas; already got customer's good reputation.
Q: What about your pharmaceutical machine price?
A: Anytime we will make quality as factory life, no matter price is good or not for us. Quality is first, on the top quality basis, Sure you will get reasonable and satisfied pricel.
Q: How can you ensure the machine's quality after we put the order?
A: Before the delivery, we will send you machine's pictures and videos, or you can come to us to have the quality checking by yourself, or by the third party inspection organization contacted by your side.
Q: What about your installation service and sales service for pharmaceutical machine?
A: 1>Guarantee is one year, we will supply spare parts or send engineers to your side if you need, we will give you service anytime, 24 hours, 7days.
2>We already prepare technical manual and operation video to show our customers, then it will be easy to install and use the machine.
3>It is free to train your worker in our factory or in your side or by video.
Complaint
