Description
RDJ500/1500-200.2000 Type Hot Isostatic Press
Main Technical parameters
- Maximum working pressure: 200MPa;
- Maximum working temperature: 2000ºC,Common operating temperature:1850ºC;
- The effective diameter of heat zone:Φ500mm;
- The effective height of heat zone:1500mm;
- Heating material:C/C;
- Temperature thermocouple:WRe3/25(JB/T9497-2002),when working temperature is not less than1700ºC,the Thermocouple service life is 1 furnace time;
- Working medium:high purity nitrogen or argon(99.99%);
- Vacuum degree(room temperature,no working parts):≤500Pa;
- Vacuum time(room temperature,no working parts):t≤30min;
- Maximum temperature deviation of effective hot zone from 800ºC to 1850ºC(no working parts,Heat preservation stage,pressure 50MPa~150MPa,Refer to GB/T9452-2012 and adopt the WRE3/25 workpiece thermocouple for 9 point temperature measurement):≤±10ºC;
- Heating up time(no working parts):room temperature~1850ºC≤4h;
- 0~60MPa Prepressurized time(no working part):≤4h;
- Maximum weight capacity of working table:600kg;
- Gas recovery rate:≥80%;
- Pressure measurement accuracy:≤0.5%F.S.;
- Loading mode: upper loading;
- Install way: Pit installation, ground operation
Operating conditions
- Altitude:≤2000m;
- Temperature:+5ºC~+40ºC;
- Relative humidity of air is not more than 90%(20ºC);
- Power supply requirement:Installation power is about 1200kW(AC380V±10%,50Hz±1%,TN-S income wire system);
- Water supply requirement:Pressure0.3~0.5MPa, Flow≥50m³/h,Water inlet temperature ≤30ºC,Water outlet temperature≤45ºC;
- The working limit height of the crane hook in the workshop of the hot isostatic press is from the ground≥5.5m,hoisting weight≥6t;
- A place free from fire,serious pollution,chemical corrosion,violent vibration and strong disturbance sources.
Our main type of press is as follows:
1. Cold Isostatic Press:S.NO. | Type | Diameter of Pressure Vessel | Depth of Pressure Vessel | Maximum Isostatic Pressure |
1 | CIP 200/300-300 | 200mm | 300mm | 300Mpa |
2 | CIP 200/1000-300 | 200 mm | 1000mm | 300Mpa |
3 | CIP 420/4000-320 | 420mm | 4000mm | 320Mpa |
4 | CIP 500/1200-400 | 500mm | 1200mm | 400Mpa |
5 | CIP 500/1500-300 | 500mm | 1500mm | 300Mpa |
6 | CIP 710/2000-250 | 710mm | 2000mm | 250Mpa |
7 | CIP 1000/3500-200 | 1000mm | 3500mm | 200Mpa |
a. The vessel inner materials is 34CrNi3MoV alloy whole parts forged and then The forged vessel be wire wounded by alloy of wire(65Mn steel 1.5mm x 6mm size) as per the designed.
b.Whole procedure of the
cold isostatic pressing (CIP) machine, increasing, holding and releasing pressure is controlled by PLC and also there is a decompression system to protect the system over pressure to keep the machine in safety running
2. Hot Isostatic Press:S.NO. | Type | Diameter of Pressure Vessel | Height of Pressure Vessel | Pressure | Temperature |
1 | HIP 800/1200-150/1000 | 800mm | 1200mm | 150Mpa | 1000degrees |
2 | HIP 1250/2000-200/1400 | 1250mm | 2000mm | 200Mpa | 1400degrees |
3. Warm Isostatic Press:S.NO. | Type | Diameter of Vessel | Length of Vessel | Pressure | Temperature |
1 | WIP D500-L2000/P200mpa-T300 | 500mm | 2000mm | 200Mpa | 300degrees |
2 | WIP D300-L1500/P250mpa-T200 | 300mm | 1500mm | 250Mpa | 200degrees |
3 | WIP D630-L2000/P250mpa-T300 | 630 mm | 2000mm | 250Mpa | 300degrees |
a.The vessel inner materials of WIP is 34CrNi3MoV alloy whole parts forged and then The forged vessel be wire wounded by alloy of wire(65Mn steel 1.5mm x 6mm size) as per the designed.
b.Whole procedure of the
warm isostatic press machine (WIP ) , increasing, holding and releasing pressure is controlled by PLC and also there is a decompression system to protect the system over pressure to keep the machine in safety running.
Contact Us: Marketing Manager: | George Sun |
Tel: | +86 13401926888 + 86-25-84508704 |
| |
Website: | chinasun99.en.made-in-china.com |
Address: | 88# Zhujiang Road,Nanjing,Jiangsu,China |