Non Toxic Silicone Chemical Industrial Equipment Mold Glue Silicone Grease Making Machine

Min.Order: 1
Product origin: Foshan, Guangdong, China
Infringement complaint: complaintComplaint
US$ 5000 ~ 8000

Description

Arm Kneader is an ideal equipment , design for mixing , kneading , crushing , dispersing high viscosity plastic materials , and has good performance in uniform mixing , no dead ends and high efficiency kneading It has six major components . kneading part , base part , the transmission system , vacuum system , hydraulic system , electric control system , etc .Place of all the contact material is made of stainless steel . There are three choices of oil circulation , electric heating , steam and water cooling.The heating and cooling can be carried out according to the requirements made of the cylinder jacket , wallboard jacket ,stirring blade pass water through hot oil structure . Discharge hydraulic cylinder turned ; screw the material under the loading and other forms .The paddle shaft seal with a unique equilibrium structure of the vacuum tank to prevent the the fillers wear particles into the cylinder , particularly favorable to improve the system vacuum and material purity.It is widely used in many industries : high viscosity sealant , silicone rubber , BMC , adhesive , also , used in batteries , ink , pigments , dyes , pharmaceuticals , resins , plastics , rubber , cosmetics  ects.
 

 

Introduction

1) Kneading machine does very well in mixing, kneading, crushing and dispersing for high viscosity liquid materials, with no dead point. 
2)Two sigma or Z-type blades.
3)Equipped with inverter for frequency control.
4)Vacuum and high pressure are available
5)The cylinder is opened hydraulically. 
6)Discharge mode: Hydraulic tilting, Bottom pumping,or Screwing.
7)With jacket outside of the cylinder, for heating or cooling.
8)Heating mode: Hot oil, Electric or Steam.
9)All the parts that contact with material are made of stainless steel.
JCT Jacketed Heating Vacuum Kneading Machine (NHZ-600)

Technical parameters

 

Model

 

Chamber Volum(L)

Drive motor power

(KW)

Mixing Speed (rpm)

 Discharge mode

 Heating

Full volume

Feeding amount

Paddle fast / slow paddle

 Optional parametersOptional parameters 

NHZ-5

5

3

2.2-4

75/50

Manual / Hydraulic tilting

Running Hot

oil

Electrical heating

Pressure Steam

NHZ-20

20

12

3-5.5

63/42

NHZ-50

50

30

4-7.5

63/42

NHZ-100

100

60

5.5-7.5

43/29

NHZ-200

200

120

7.5-15

43/29

Hydraulic tilting

The bottom pumping

Screw extruding

NHZ-300

300

180

11-18.5

43/29

NHZ-500

500

300

18.5-30

43/29

NHZ-1000

1000

600

22-55

32/22

NHZ-1500

1500

900

30-90

32/22

NHZ-2000

2000

1200

45-110

32/22

NHZ-3000

3000 

1800 

55-130 

33/22 

Remarks:

1,Temperature range: 0-300°,

2, Pressure range:-0.1-0.6MPa,

3,Inverter for frequency control if necessory.

 

Available products:


1. Unsaturated resins, alkyd resins, acrylic resins, polyurethane and other complete sets of production equipment;
2. Latex, white latex, rubber coating, film coating, all-purpose adhesive and other complete sets of production equipment;
3. Glass, plastic, silicone rubber, sealants and other sets of production equipment;
4. Raw rubber sets of production equipment;
5. Silicone waste pyrolysis recycling old solvent distillation recovery sets of production equipment;
6. Hot melt adhesive sets of production equipment;
7. Various types of powder mixing auger sets of production equipment;
8. Various non-standard chemical equipment design, production and installation.

about us

FAQ

Q : Can you send the formula for the products we want to make ?
A : Our machines can be used for many kinds of product making ,such as Resin , Paint, Adhesive , Cosmetic , Food , Chemicals . There are many kinds of these products , so it's impossible for us to know all the formulas and technologies . We can assist you to find the raw material list you need , and after you place order with us , we can help you to find formula and technology , there will engineers to teach you how to make the product , and the cost will be on your account.  

Q : Do you have machines in stock ?
A : Yes , but just the small-scale machines Machines are different with other products , most of the large-scale machines are designed according to our customers 'requirements different customers have different production requirements , so the technical parameter is different for most machines On the other hands , most of the our machines will cover a large area , so once the machines are finished , we will effect shipment after QC . 

Q : Can you send the detailed drawings of the machine to us before we place order ?
A : We can send you a draft drawing of the machines , and after you place order and pay the deposit , our engineer will design the send you the detailed drawings . Once you confirm without questions , we will put it into production.

Scroll to Top