Complaint
Safety light curtains are also photoelectric safety protection devices (safety protectors, punch protectors, infrared safety protection devices, etc.). In modern factories, people and machines work together, and they can be installed on some potentially dangerous mechanical equipment to protect workers. Prevent security incidents from happening.
For Example, stamping machinery, shearing equipment, metal cutting equipment, automated assembly lines, automated welding lines, mechanical transmission, and handling equipment, and hazardous areas (toxic, high pressure, high temperature, etc.), are likely to cause personal injury to operators, can be installed.
1. The unique structural design ensures that there is no blind spot in the entire protection area;
2. Dual-channel OSSD output function, which can be cross-monitored with each other;
3. The self-diagnosis function can detect the failure circuit module of the light curtain. and issue an alarm signal;
4. With interlock reset, external test, and EDM function, strengthen the output monitoring ability;
5. Adopt optical communication synchronization, simplify the electrical connection and make the operation easier;
6. Meet the requirements of Type 4, SIL3 and PLe safety levels, and can be used for the protection of various parts of the body;
7. Waterproof design to meet outdoor applications
| LSA series safety light curtain | ||||
| Model | LSA10 | LSA20 | LSA40 | LSA80 |
| General parameters : | ||||
| Space between beams | 10mm | 20 mm | 40mm | 80mm |
| Number of optical beams | 32~192 | 16~96 | 08~48 | 08~24 |
| Min detection object | 15 mm | 26 mm | 46 mm | 86 mm |
| Detection distance | 0.5 m ~6m | 0.5 m ~8m | ||
| Light source | 850nm infrared light | |||
| Protection height | 320mm...1,920 mm | |||
| Mechanical and electronic parameters: | ||||
| Supply voltage: | 24v DC ± 20% | |||
| Power consumption | ≤5W | |||
| Power-on delay | 2s | |||
| Working current | Max.300 mA | |||
| Response time | 3ms~52ms(depends on the optical beams quantity) | |||
| Safety output OSSD | 2-ways NPN/PNP Normal close; Short circuit protection, Cross circuit monitoring ;output current< 200mA(30v DC) Switch-on voltage drop :≤1.5v; Cutoff voltage :≤ 1.2V; Load capacitance :30nF; Load inductance :2.2H; Power supply cable resistance :≤ 10Ω; OSSD Test pulse width :200 ~ 300us; OSSD Test pulse period :50 ~ 100ms; | |||
| EDM Selecting input | The input is suspended or connected to low level, the EDM input is invalid and connected to high level, the EDM input is valid; High level: 10 ~ 30V DC, current less than 10mA; Low Level: 0-2V DC | |||
| EDM( External equipment monitoring )input | Through the EDM input terminal, the 24V DC signal from the external equipment contactor can be monitored. High level: 10 ~ 30V DC, current less than 10mA; Low Level: 0-2V DC | |||
| RESET(Reset)input | Manual reset: RESET input terminal is connected to high level through manual switch. Automatic reset: RESET input terminal is connected to high level. High level: 10 ~ 30V DC, current less than 10mA; Low Level: 0-2V DC. | |||
| Indicators | Power(Green ),Fault(Yellow),Shelter(Red),Alignment(Blue 3 pieces). | |||
| Communication | Optical synchronization | |||
| Protection rate | IP65 | |||
| Work temperature | -25ºC~50ºC RH 15~95% | |||
| Connector | M12,6 Pins(Emitter),8 Pins(Receiver) | |||
| Dimension | As per models | |||
| LSA20 series | ||||||
| Model | Detection Distance(m) | Resolution ratio (mm) | Light beams quantity | Safe height (mm) | Response time( m s) | Product Length(mm) |
| LSA20016 | 0.5~8m | 26mm | 16 | 320 | 5.1 | 325 |
| LSA20024 | 24 | 480 | 7.1 | 485 | ||
| LSA20032 | 32 | 640 | 9.1 | 645 | ||
| LSA20040 | 40 | 800 | 11.3 | 805 | ||
| LSA20048 | 48 | 960 | 13.4 | 965 | ||
| LSA20056 | 56 | 1120 | 15.5 | 1125 | ||
| LSA20064 | 64 | 1280 | 17.6 | 1285 | ||
| LSA20072 | 72 | 1440 | 19.7 | 1445 | ||
| LSA20080 | 80 | 1600 | 21.8 | 1605 | ||
| LSA20088 | 88 | 1760 | 23.9 | 1765 | ||
| LSA20096 | 96 | 1920 | 26.0 | 1925 | ||
Product self-inspection steps
1. Detect whether the installation position of the object and the proximity sensor has deviated, slacked, or skewed; whether there is slack, poor contact, or disconnection in the wiring and connection parts
2. Whether there is adhesion or accumulation of metal dust, etc.
3. Is there any abnormality in using temperature conditions and environmental conditions?
4. Set whether the flashing of the display lamp type is abnormal.
If you must be careful not to disassemble and repair by yourself during the inspection, and to easily find out the fault, you can investigate the operating state of the sensor through the connection with the portable detector, and then repair it according to the situation.
In order to make the photoelectric sensor work stably for a long time, it should be regularly checked with the same contents as the general control equipment to maintain its long-term function. The photoelectric sensor can also be stocked. Once a problem with the photoelectric sensor is found, we can replace it in time without affecting the use of the sensor.
| About G-TEK Sensor | |
| 1 | Tianjin G-TEK Automation Technology Co., Ltd. was established in 2003, its main products are photoelectric sensors and proximity sensors; |
| 2 | In 2004, the LST infrared vehicle separator, also known as the infrared vehicle separating light curtain independently developed by the company came on the market and gradually occupied the domestic market of highway toll weighing system |
| 3 | In 2009, the Haitai Green Industrial Park established production and operation workshops, the same year a new generation of intelligent defrost-type infrared vehicle separator LHA (C) series curtain sensor came out, and was supported by the National Innovation Fund |
| 4 | In 2013, further, expand the scale of production and operation, and set up special workshops for the production of sensor switches and vehicle separators light curtain sensors |
| 5 | In 2014, the research and development team and sales team of the company are strengthened, the new research and development production base project is launched, and Tianjin G-TEK Sensor Technology Co., Ltd. is registered and established |
| 6 | In 2016, G-TEK passed the certification of national high-tech enterprises, and the construction of the new R&D and production base of G-TEK began at the end of the same year |
| 7 | At the end of 2017, the first long-distance, high-precision, and fast-scanning LSD101 laser sensor was officially released; the Shenzhen Office was established in the same year |
| 8 | The whole series of Lidar products were launched in 2018, and the TOF 3D vision sensor was introduced |
| 9 | The new R&D and production base of G-TEK is completed and the company is relocated in 2019, effectively expanding the R&D, production, and quality assurance capabilities |
| 10 | In 2020, the company participates in the national highway renovation project, and the lidar vehicle profile system is widely used in domestic ETC projects, achieving a new high annual sales, and is rated as the top 50 private enterprises in Xiqing District, and the research and development center of the company is rated as a district-level technology center |
| 11 | In 2021, LDN was launched, the LMO series laser scanner product project was launched, several photoelectric sensor products were upgraded, the company's production system was further expanded, and great progress was made in the warehousing logistics industry market development |
