China Professional Gypsum Powder Grinding Wet and Dry Ball Mill Machine by Boiling Furnace Process

Min.Order: 1
Product origin: Linyi, Shandong, China
Infringement complaint: complaintComplaint
US$ 150000 ~ 600000

Description
I Specific technical parameters of gypsum plaster powder production line manufacturer


1.Raw material request 
Main quality indexes of raw materials
CaSO4·2H2O content:75% ~ 95%
Surface water content ≤ 18%
Crystal water content 18-20%
Capacity
15,000ton-400,000ton/year , based on 24hour/day ,300days/year 
Fuel 
Gas /coal /heavy oil/diesel
Electricity 
380V/50HZ 
Quality standard
Quality meets and exceeds the national standard of gypsum powder Construction gypsum national standard number GB 9776-88

2.Powder parameters
1.Product quality
Reach or exceed the china (GB9776-88  building gypsum ) requirements.
2.Fineness
100 mesh-120mesh
3.Bending strength 
Bending strength 1.8 Mpa; Compressive strength: was 3.0 Mpa.(The bending strength have direct relations with raw material) 
4.Main relative composition
1)Soluble anhydrous gypsum content:≥ 80% adjustable
2)The content of dihydrate gypsum: < 5% adjustable
3)Initial setting time: 3 ~ 8 min adjustable; Final setting time: 6 ~ 15 min adjustable.
4)Scale thick: 78 ~ 85% adjustable.

3. Labor requirements
From raw materials to drying 1 person /8 hours
Heating supply 1 person /8 hours
Calcinate control    1 person /8 hours
Electrical work    1 person /12 hours
Machine repair  1 person /12 hours

II Whole plant of gypsum plaster powder production line manufacturer
Gypsum powder plant mainly consist of main unit, classifier, powder collector, dust cleaner, blower, muffler, sound-proof room, crusher, bucket elevator, storage hopper, and vibrating feeder.


Features of  gypsum plaster powder production line manufacturer
1. Continuous production: using hammer dryer and soft start,
2. Quality stability: modification mill can increase the specific surface are of materials.
3. Energy conservation and stability: great brand frequency transformer
4. High performance of equipment: using bag dust collector ,water bath desulfurization and denitration treatment,frequency transformer,Siemens electrical, PLC, Guomao reducer, national standard cable, electrical control: ABB.
5. Easy control: adopt computer display, PLC control.
6. Mature experience: The core features of our company are mature technologies that can provide a solid foundation for your company.

III Sample project of 
 gypsum plaster powder production line manufacturer



IV Hot air boiling furnace and hot oil furnace technology comparison

1.Reduce investment
The system does not use hot oil kiln , which saves the fixed investment in this part (e.g., oil furnace body, circulating oil pump, pipe, insulation, valve, high-low oil tank, etc.)

2.Power saving
This system saves the circulation pump, the base power is 45KW/200T/24 hours, the motor 24 hours consumption of electricity is 45X24=1080 degrees

3.Maintenance cost
The oil stove is need to change a cycle oil once a year, and the replacement cost is about USD3174.60-4761.9The oil pipeline should be cleaned regularly, while the boiling wok is direct heat transfer and does not need to be cleaned.

4.Comprehensive utilization rate
Because of this system, using the waste heat utilization, tail smoke emission temperature less than 90 ºC, reduces the cost of coal, and heat conduction oil smoke exhaust temperature is 250 ºC or higher, so the new technology is more energy saving. Built-in dust collecting device, simple structure, no need of power, no need maintenance, recovery of gypsum powder back to the calcining chamber. 2-5 tons of gypsum powder can be received daily, and 2 to 3 yuan($0.32-$0.48) per ton of gypsum powder can be reduced.

5.Quality adjustable
The system adopt FD - chamber boiling furnace technology, gypsum powder under different air temperature, different area, fully dehydration in different stages, make the product in the case of without adding any additives, the setting time can be adjusted in 3-15 minutes and normal consistency of 66% - 75%.

6.The installation period is short and the area is small
This system has simple structure, compact, no cumbersome pipe valves and related certificates. Easy maintenance, less land occupy .

7.Environmentally friendly
This system USES a three-stage dust removal, cyclone dust collect , the electric dust collect , water bath dust removal or bag dust collector, the discharge of tail smoke more clean. According to the requirements of users can provide users with more complete equipment and environmental protection technology.

V . Our service 
 Our after-sale service
1
We offer technical support until the workers know how to operate.
2
The operating instruction will go to the customers with the equipment. Technology data and relative files for high pressure gypsum powder production line 
3
We provide lifelong guidance . Visiting clients in regular times.
4
Excellent easy-broken parts support for buyers. Easy-broken parts guarantee for one year.


VI .Our company and contact information 

Shandong Yurui machinery CO.,lTD , We have rich experience in gypsum series products making equipment field. Our general engineer has over 20years experience, other main engineers all have over 10 years experience, proficient in the newest gypsum board manufacturing plant design and manufacturing. What we provide is not only the machine, but a whole system. We will provide the installation, commissioning, purchasing the raw material and solve any problem timely. We will provide one year guarantee.Workshop design, equipment installation, Workers'trainning. Formular's upgrade are on time provide. With over 100 projects in domestic and abroad markets, we can ensure you a successful project. 








Any questions please feel free to contact     


 
Product Tag:
Related categories:
Scroll to Top