| G101/G102 C101/C102 | |
| PICK THE CORRECT SERIES | |
| NO. | DESCRIPTION | GENERAL NO. |
| Not Shown | ONLY HEX NUT | 391-1451-076 |
| 2 | ONLY WASHER | 391-3784-028 |
| 3 | 101 BRACKET OPTIONAL | 314-0100-005 |
| 4 | 101 SNAP RING | 391-2681-493 |
| 5 | 101 LUIP SEAL | 391-2883-096 |
| 6 | 101 SHAFT END COVER | 314-5039-201 |
| 7 | RING SEAL | 391-2585-009 |
| 8 | ROLLER BRG. | 391-0381-059 |
| 9 | THRUST PLATE | 391-2185-012 |
| Not Shown | POCKET SEAL | 391-2882-050 |
| 11 | 101 SHAFT & GEAR SET | 314-29XX-640 |
| 12 | GEAR HOUSING GASKET | 391-2884-021 |
| 13 | GEAR HOUSING | 314-80XX-100 |
| 14a | 101 PORT END COVER | 314-3910-903 |
| 14b | 102 PORT END COVER | 314-3910-904 |
| 15 | SPOOL VALVE | 314-4000-001 |
| 16 | QUAD RING | 391-2881-103 |
| 17 | WIPER RING | 391-2883-147 |
| 18 | C ONLY RETAINER RING | 391-3782-126 |
| 19 | C ONLY SNAP RING | 391-2688-003 |
| 20 | DETENT CAP | 314-0100-003 |
| 21 | DETENT BALL | 391-0282-009 |
| 22 | DETENT SPRING | 391-3581-383 |
| 23 | LOCK WASHER | 391-3788-002 |
| 24 | DETENT RETAINER | 391-2583-079 |
| 25 | RELIEF VALVE | 355-9001-067 |
| 26 | WASHER | 391-3784-029 |
| 27a | CAP SCREW / MH101-20 | 391-1401-111 |
| 27b | CAP SCREW / MH101-25 | 391-1401-110 |
| 28a | CAP SCREW / MH102 -20 | 391-1425-433 |
| 28b | CAP SCREW / MH102 -25 | 391-1425-432 |
| 29 | OPTIONAL SLEEVE | 391-3283-052 |
| 30 | PIPE PLUG | 391-2282-006 |
| 31 | SPOOL END CAP | 391-1881-073 |
| 32 | SPIRAL PIN | 391-2085-009 |
| 33 | BRACKET | 391-0981-010 |
| 34 | S.H.C.SCREW | 391-1402-063 |
| Not Shown | 102 SNAP RING | 391-2686-065 |
| Not Shown | 102 SEAL RETAINER | 391-3383-087 |
| 36 | 102 SPACER | N/A |
| 37 | 102 LIP SEAL | 391-2883-115 |
| 38 | 102 SHAFT END COVER | 313-5037-201 |
| 39 | CHECK VALVES | 391-3681-001 |
| 40 | MH 102 SHAFT & GEAR SET 7/8" x 13 tooth spline | 314-29XX-130 |
| 41a | CAP SCREW 1 MH101-102 | 391-1401-082 |
| Not Shown | SHAFT KEY | 391-1781-021 |
| Not Shown | SEAL RETAINER | N/A |
| | | |
| P30/P31 | |
| NO. | DESCRIPTION | GENERAL NO. |
| 1 | SHAFT BEARING SN P RING | 391-2686-063 |
| 2a | INPUT SHAFT BEARING | 391-0381-040 |
| 2b | BEARING SPACER ( IN PLACE OF SHAFT BEARING) | 391-3383-068 |
| 3 | MOTOR SEAL RETAINER USED WITH SHAFT BEARING OR SPACER | 391-3381-040 |
| 4a | PUMPLIP SEAL FOR CONTINENTAL SHAFT ONLY | 391-2883-107 |
| 4b | PUMP LIP SEAL FOR PIGGY BACK 76/31 SHAFT END COVER | 391-2883-103 |
| 4c | MOTOR UIP SEAL | 391-2883-119 |
| 4d | MOTOR UIP SEAL FOR CONTINENTAL SHAFT ONLY | 391-2883-126 |
| 5a | 31 PAD PILOT PUMP S.E.C. TYPE 00 | 312-5017-201 |
| 5b | 31 6 BOLT ROUND WITH 2.625* or 66,67 mm PILOT PUMP S.E.C. TYPE 05 | 312-5047-201 |
| 5c | 31 4 BOLTB PILOT PUMP S.E.C. TYPE 42 (4" or 101,6 mm pilot) | 312-5037-201 |
| 5d | 31 4 BOLT CPILOT PUMP S.E.C. TYPE 78 (5" or 127 mm pilot) | 312-5037-202 |
| 5e | 31 2 BOLTAPILOT PUMP S.E.C. TYPE 94 (3 1/4" or 82.55 mm pilot) | 312-5027-204 |
| 5f | 31 2 BOLTB PILOT PUMP S.E.C. TYPE 97 (4" or 101,6 mm pilot) | 312-5027-201 |
| 5g | 31 2 BOLT B (TYPE2) PILOT PUMP S.E.C. TYPE 96 (4" or 101,6 mm pilot) | 312-5027-205 |
| 5h | [ 31/51 SHAFT END COVER FOR PIGGYBACK UNITS TYPE 91 | 312-5027-208 |
| 5i | 76/31 SHAFT END COVER FOR PIGGYBACK UNITS TYPE 92 | 312-5027-209 |
| 5j | 31 2/4 BOLTB PILOT PUMP S.E.C. TYPE 46 (4" or 101.6 mm pilot) | 312-5053-202 |
| 5k | 31 PAD PILOT MOTOR S.E.C. TYPE 00 | 312-5017-401 |
| 5L | 31 6 BOLT ROUND WITH 2.625"or 66,67 mm PILOT MOTOR S.E.C. TYPE 05 | 312-5047-401 |
| 5m | 31 4 BOLTB PILOT MOTOR S.E.C. TYPE 42 (4" or 101,6 mm pilot) | 312-5037-401 |
| 5n | 31 4 BOLT C PILOT MOTOR S.E.C. TYPE 78 (5 or 127 mm pilot) | 312-5037-402 |
| 5o | 31 2 BOLT A PIL OT MOTOR S.E.C. TYPE 94 (3 14 or 82,55 mm pilot) | 312-5027-404 |
| 5p | 31 2 BOLT B PILOT MOTOR S.E.C. TYPE 97 (4" or 101,6 mm pilot) | 312-5027-401 |
| 5q | 31 2/4 BOLTB PILOT MOTOR S.E.C. TYPE 46 (4" or 101,6 mm pilot) | 312-5053-402 |
| | FOR MORE INFORMATION OR SPECIAL ORDER,PLEASE CONTACT US | GENERAL NO. |
| 6a | CHECK VALVE MOTOR | 391-3681-001 |
| 6b | PRESSURE PLUG PUMP | 391-2286-004 |
| 7 | RING SEAL | 391-2585-006 |
| 8 | ROLLER BEARING (∅1.687" O.D.) | 391-0381-068 |
| 9a | PUMP THRUST PLATE | 391-2185-031 |
| 9b | MOTOR THRUSTPL ATE | 391-2185-013 |
| 10 | POCKET SEAL | 391-2882-086 |
| 11a | SHAFT & GEAR TYPE 30 (0.875" ∅ x 1/4" x3/B" x 1" key) | 312-29XX-730 |
| 11b | SHAFT & GEAR TYPE 25( 0.875" ∅- 13-ooth splin) | 312-29XX-230 |
| 11c | SHAFT & GEAR TYPE 43 (1.00" ∅x 14" x 14" x11/4" key) | 312-29XX-740 |
| 11d | SHAFT & GEAR TYPE 65 TYPE 2( 0.875" ∅- 13-Tooth spline) | 312-29XX-430 |
| 11e | SHAFT & GEAR TYPE 65 TYPE 98(1"∅ - 15-Tooth splin) | 312-29XX-240 |
| 12 | PUMP & MOTOR HOUSING GASKET | 391-2884-050 |
| 13 | PUMP & MOTOR GEAR HOUSING | 312-82XX-100 |
| 14a | 31 MOTOR BEARING CARRIER BLANK | 312-7740-100 |
| 14b | 31 PUMP BEARING CARRIER WITH COMMON PASSAGE | 312-7723-100 |
| 15 | CONNECTING SHAFT | 312-1133-001 |
| 16 | GEAR SET ONLY | 312-28XX-000 |
| 17 | GEAR HOUSING DOWEL PIN | 391-2082-032 |
| 18a | 31 PUMP & MOTOR PORT END COVER | 312-3120-100 |
| 18b | 31 PUMP & MOTOR PORT END COVER LARGER PORTING | 312-3420-100 |
| 18c | 31/31 PIGGY BACK PORT END COVER | 312-5027-212 |
| 19 | FLAT WASHER | 391-3784-028 |
| 20 | BOLTS/ STUDS (5/8" UNC) | |
| 21 | HEX NUT (5/8 UNC) | 391-1451-076 |
| 22a | CONTINENTAL SHAFT TYPE 30 (0.875"∅x14" x 3/8" x 1"key) | 312-1500-300 |
| 22b | CONTINENTAL SHAFT TYPE 7 (1.250" ∅- 14-tooth splne, Continental only) | 312-1135-133 |
| 22c | CONTINENTAL SHAFT TYPE 25 ( 0,875" ∅- 13-Tooth spline) | 312-1135-138 |
| 22d | CONTINENTAL SHAFT TYPE43 (1.00" ∅x14" x 3/8" x1 14" key) | 312-1500-400 |
| 22e | CONTINENTAL SHAFT TYPE 12 (0. 750" ∅x 3/16" x 3/16" 19/16- key) | 312-1135-152 |
| 221 | CONTINENTAL SHAFT TYPE 95 (0. 625" ∅ x 9tooth spin) | 312-1000-200 |
| 23 | CONTINENTAL SHAFT BRG. RETAINER | 312-0100-002 |
| 24 | CONTINENTAL SHAFT BRG. RETAINER SNAP RING | 391-2685-011 |
| Not Shown | PUMP & PIGGY BACK 31/31 S.E.C.LIP SEAL | 391-2883-058 |
| Not Shown | SEAL RETAINER FOR 51/51& 31/51 PIGGY BACK PUMP S.E.C. | 391-2584-063 |
| Not Shown | SEAL RETAINER 0 RING FOR PIGGY BACK PUMP S.E.C. | 391-2881-124 |
| Not Shown | SEAL RETAINER 0 RING FOR PIGGY BACK PUMP S.E.C. | 391-2881-120 |
| Not Shown | SEAL RETAINER FOR 76/51 & 76/31 PIGGY BACK PUMPS.E.C. | 391-2585-013 |
| Not Shown | CASE DRAIN PLUG | 391-2282-056 |
| Not Shown | SHAFT KEY FOR TYPE 12 SHAFT | 391-1781-075 |
| Not Shown | SHAFT KEY FOR TYPE 43 & 67 SHAFT | 391-1781-021 |
| Not Shown | SHAFT KEY FOR TYPE 30 & 66 SHAFT | 391-1781-025 |
| Not Shown | SHAFT KEY FOR TYPE Spl.SHAFT | 391-1781-020 |
| Not Shown | 30130 PIGGY BACK CONNECTING SHAFT | 312-1133-002 |
| Not Shown | 50/30 PIGGY BACK CONNECTING SHAFT | 312-1133-003 |
| Not Shown | 75/30 PIGGY BACK CONNECTING SHAFT | 316-1133-003 |
| | | |
| P50/P51 | |
| NO. | DESCRIPTION | GENERAL NO. |
| 1 | SHAFT BRG.SNAP RING | 391-2686-065 |
| 2a | BEARING SPACER & SEAL RETAINER FOR MOTORS | 391-3383-087 |
| 2b | INPUT SHAFT BEARING | 391-0381-077 |
| 3 | MOTOR SEAL RETAINER USED WITH SHAFT BEARING | 391-3383-020 |
| 4a | PUMP LIP SEAL | 391-2883-103 |
| 4b | MOTOR LP SEAL | 391-2883-115 |
| 4c | PUMP LIP SEAL FOR CONTINENTIAL SHAFT ONLY | 391-2883-133 |
| 5a | 51 PAD PI .OT PUMP SHAFT END COVER TYPE 00 | 313-5017-201 |
| 5b | 51 4 BOLTB PILOT PUMP SHAFT END COVER TYPE 42 (4" or 101,6 mm pilot) | 313-5037-201 |
| 5c | 51 4 BOLT c PIL OT PUMP SHAFT END COVER TYPE 78 (5" or 127 mm pilot) | 313-5037-202 |
| 5d | 51 2 BOLTB PILOT PUMP SHAFT END COVER TYPE 97 (4" or 101.6 mm pilot) | 313-5027-201 |
| 5e | 51 2 BOLT C PIL OT PUMP SHAFT END COVER TYPE 98 (5" or 127 mm pilot) | 313-5027-202 |
| 5f | 51 2 BOLT B (TYPE 2) PILOT PUMP SHAFT END COVER TYPE 96 (4" or 101,6 mm pilot) | 313-5027-205 |
| 5g | 51 2 BOLT C (TYPE 2) PIL OT PUMP SHAFT END COvER TYPE 99 (5" or 127 mm pilot) | 313-5027-206 |
| 5h | 51/51 SHAFT END COVER FOR PIGGYBACK UNITS TYPE 91 | 313-5027-208 |
| 51 | 76/51 SHAFT END COVER FOR PIGGYBACK UNITS TYPE 92 | 313-5027-209 |
| 5j | 51 PAD PILOT MOTOR SHAFT END COVER TYPE 00 | 313-5017-401 |
| 5k | 51 4 BOLT B PL oT MOTOR SHAFT END COVER TYPE 42 (4" or 101.6 mm pilot) | 313-5037-401 |
| 5L | 51 4 BOLT C PILOT MOTOR SHAFT END COVER TYPE 78 (5" or 127 mm pilot) | 313-5037-402 |
| 5m | 51 2 BOLT B PILOT MOTOR SHAFT END COVER TYPE 97 (4" or 101,6 mm pilot) | 313-5027-401 |
| 5n | 51 2 BOLT C PILOT MOTOR SHAFT END COVER TYPE 98 (5" or 127 mm pilot) | 313-5027-402 |
| | FOR MORE INFORMATION OR SPECIAL ORDER,PLEASE CONTACT US | GENERAL NO. |
| 6a | CHECK VALVE MOTOR | 391-3681-001 |
| 6b | PRESSURE PLUG PUMP | 391-2286-004 |
| 7 | RING SEAL | 391-2585-009 |
| 8 | ROLLER BEARING (∅1.937" 0.D.) | 391-0381-059 |
| 9a | PUMP THRUST PLATE | 391-2185-029 |
| 9b | MOTOR THRUST PLATE | 391-2185-012 |
| 9c | DRY VALVE THRUST PLATE | 391-2185-041 |
| 10 | POCKET SEAL | 391-2882-050 |
| 11a | SHAFT & GEAR 14 TOOTH SPLINE 1.228"maj. dia. TYPE7 | 313-29XX-250 |
| 11b | SHAFT & GEAR 1.250* KEYED (5/16) YPE 11 | 313-29XX-750 |
| 11c | SHAFT & GEAR SET 13 TOOTH SPLINE 0.858"maj dia TYPE 25 | 313-29XX-230 |
| 11d | SHAFT & GEAR SET 0.9984" dia. KEYED (14" x3/8" x1 14) TYPE 43 | 313-29XX-740 |
| 11e | SHAFT & GEAR 14 TOOTH SPLINE 1.228* ma]. dia. TYPE 53 TYPE 2 | 313-29XX-450 |
| 11f | SHAFT & GEAR SET 13 TOOTH SPLINE 0.858* maj. dia TYPE 65 TYPE2 | 313-29XX-430 |
| 12 | PUMP & MOTOR HOUSING GASKET | 391-2884-021 |
| 13 | HOUSING DOWELL PIN | 391-2082-032 |
| 14 | PUMP & MOTOR GEAR HOUSING | 313-82XX-100 |
| 15a | 51 MOTOR BEARING CARRIER BLANK | 313-7740-100 |
| 15b | 51 PUMP BEARING CARRIER WITH COMMON PASSAGE | 313-7723-100 |
| 16 | CONNECTING SHAFT | 313-1133-001 |
| 17 | GEAR SET ONLY | 313-28XX-000 |
| 18a | 51PUMP & MOTOR PORT END COVER | 313-3120-100 |
| 18b | 51 PUMP & MOTOR PORT END COVER SPECIAL LARGER PORTING | 313-3420-100 |
| 18c | 51 PIGGY BACK REAR PORT END COVER | 313-5027-212 |
| 19 | FLAT WASHER (5/8*) | 391-3784-028 |
| 20 | BOLTS/STUDS (518"-UNC) | |
| 21 | HEX NUT (5/8"-UNC) | 391-1451-076 |
| 22a | CONTINENTAL SHAFT TYPE 11 (1.250" ∅ KEYED 5/16") | 313-1500-500 |
| 22b | CONTINENTAL SHAFT TYPE 7 (1.250" ∅- 14 TOOTH SPLINE) | 313-1135-194 |
| 22c | CONTINENTAL SHAFT TYPE 25 (0.875" ∅- 13 TOOTH SPLINE) | 313-1000-300 |
| 22d | CONTINENTAL SHAFT TP 43(100" ∅x 1/4" x 3/8* x 11/4" key) | 313-1500-400 |
| 22e | CONTINENTAL SHAFT TYPE 73 LONG (1 250" ∅ KEYED 5/16") | 313-1500-502 |
| 23 | CONTINENTAL SHAFT BRG. RETAINER (MAY NOT BE REQUIRED) | 391-3381-046 |
| 24 | CONTINENTAL SHAFT BRG. RETAINER SNAP RING (MAY NOT BE REQ) | 391-2685-040 |
| Not Shown | SEAL RETAINER FOR 51/51 PIGGY BACK PUMP S.E.C. | 391-2584-063 |
| Not Shown | SEAL RETAINER 0 RING FOR PIGGY BACK PUMP S.E.C. | 391-2881-124 |
| Not Shown | SEAL RETAINER 0 RING FOR PIGGY BACK PUMP S.E.C. | 391-2881-120 |
| Not Shown | SEAL RETAINER FOR 76/51 PIGGY BACK PUMP S.E.C. | 391-2585-013 |
| Not Shown | CASE DRAIN PLUG | 391-2282-056 |
| Not Shown | DRY VALVE SEAL RETAINER | 391-2584-050 |
| Not Shown | PUMP UIP SEAL FOR PIGGY BACK S.E.C.&P.E.C. | 391-2883-058 |
| Not Shown | SHAFT KEY FOR TYPE 73 SHAF | 391-1781-008 |
| Not Shown | SHAFT KEY FOR TYPE 43 SHAFT | 391-1781-021 |
| Not Shown | SHAFT KEY FOR TYPE 11 SHAFT | 391-1781-045 |
| Not Shown | 50/50 PIGGY BACK CONNECTING SHAFT | 313-1133-004 |
| Not Shown | 75/50 PIGGY BACK CONNECTING SHAFT | 313-1133-003 |
| | | |
| P75/P76 | |
| NO. | DESCRIPTION | GENERAL NO. |
| 1 | SHAFT BRG. SNAP RING | 391-2686-025 |
| 2a | INPUT SHAFT BRG. | 391-0381-078 |
| 2b | SPACER TO REPLACE SHAFT BEARING | 391-3383-018 |
| 3a | SEAL RETAINER FOR PUMPS | 391-2584-082 |
| 3b | SEAL RETAINER FOR MOTORS | 391-2584-051 |
| 4 | SEAL RETAINER 0 RING | 391-2881-457 |
| 5a | PUMP LIP SEAL | 391-2883-052 |
| 5b | MOTOR LIP SEAL | 391-2883-094 |
| 6a | 76 4 BOLT B PILOT PUMP S.E.C. TYPE 42 (4" or 101,6 mm pilot) | 316-5037-201 |
| 6b | 76 4 BOLT C PILOT PUMP S.E.C. TYPE 78 (5" or 127 mm pilot) | 316-5037-202 |
| 6c | 76 4 BOLT D PILOT PUMP S.E.C. TYPE 80 (6" or 152,4 mm pilot) | 316-5037-203 |
| 6d | 76 2 BOLT C PILOT PUMP S.E.C. TYPE 98 (5" or 127 mm pilot) | 316-5027-202 |
| 6e | 76 4 BOLT B PILOT MOTOR S.E.C. TYPE 42 (4" or 101,6 mm pilot) | 316-5037-401 |
| 6f | 76 4 BOLT C PILOT MOTOR S.E.C.TYPE 78 (5" or 127 mm pilot) | 316-5037-402 |
| 6g | 76 4 BOLT D PILOT MOTOR S.E.C. TYPE 80 (6" or 152,4 mm pilot) | 316-5037-403 |
| 6h | 76 2 BOLT C PILOT MOTOR S.E.C. TYPE 98 (5" or 127 mm pilot) | 316-5027-402 |
| 7a | CHECK VALVE MOTOR | 391-3681-001 |
| 7b | PRESSURE PLUG PUMP | 391-2286-004 |
| 8 | DOWEL PIN | 391-2082-033 |
| 9 | RING SEAL | 391-2585-011 |
| 10 | ROLLER BEARING (∅2.322" 0.D.) | 391-0381-060 |
| 11 | POCKET SEAL | 391-2882-052 |
| 12a | PUMP THRUST PLATE | 391-2185-026 |
| 12b | MOTOR THRUST PLATE | 391-2185-020 |
| 12c | DRY VALVE THRUST PLATE | 391-2185-072 |
| Not Shown | DRY VALVE THRUST PLATE SEAL | 391-2885-040 |
| | FOR MORE INFORMATION OR SPECIAL ORDER, PLEASE CONTACT US | GENERAL NO. |
| 13a | SHAFT & GEAR 14 TOOTH SPLINE 1.228"maj.dia. TYPE 7 | 316-29XX-250 |
| 13b | SHAFT & GEAR 1.250" KEYED (5/16") TYPE 11 | 316-29XX-750 |
| 14 | PUMP & MOTOR HOL JSING GASKET | 391-2884-024 |
| 15 | PUMP & MOTOR GEAR HOUSING | 316-82XX-100 |
| 16 | CONNECTING SHAFT | 316-1133-001 |
| 17a | 76 MOTOR BEARING CARRIER BLANK | 316-7740-100 |
| 17b | 76 PUMP BEARING CARRIER WITH COMMON PASSAGE | 316-7723-100 |
| 18 | GEAR SET ONLY | 316-28XX-000 |
| 19 | 76 PUMP & MOTOR PORT END COVER | 316-3120-100 |
| 20 | FLAT WASHER (5/8") | 391-3784-028 |
| 21 | BOLTS / STUDS (5/8"-UNC) | |
| 22 | HEX NUT (5/8"-UNC) | 391-1451-076 |
| 23a | CONTINENTAL SHAFT 14 TOOTH SPLINE 1.228"maj.dia. TYPE 7 | 316-1135-148 |
| 23b | CONTINENTAL SHAFT 1.250"KEYED (5/16") TYPE 11 | 316-1135-147 |
| 23c | CONTINENTAL SHAFT 14 TOOTH SPLINE 1.228". Dia. TYPE 7 Long | 316-1500-502 |
| 23d | CONTINENTAL SHAFT 1.250"KEYED (5/16") TYPE 11 Long | 316-1500-501 |
| 24 | CONTINENTAL SHAFT BRG. RETAINER | 391-3381-039 |
| 25 | CONTINENTAL SHAFT BRG. RETAINER SNAP RING | 391-2685-029 |
| Not Shown | PIGGY BACK CONNECTING SHAFT | 316-1133-003 |
| Not Shown | PUMP LIP SEAL FOR PIGGY BACKP.E.C. | 391-2883-103 |
| Not Shown | 76 PIGGYBACK REAR PORT END COVER | 316-5027-213 |
| Not Shown | DRIVE KEY FOR TYPE 11 SHAFT | 391-1781-045 |
| Not Shown | DRY VALVE ASSEMBLY 1/2" CONNECTION | 316-PMV-24 |
| Not Shown | DRY VALVE ASSEMBLY 2" CONNECTION | 316-PMV-32 |
| | | |
| P315 | |
| NO. | DESCRIPTION | GENERAL NO. |
| 1 | SEAL RETAINER SNAP RING MOTOR ONLY | 391-2686-016 |
| 2 | SHAFT BEARING ( USED IN TYPE* 9O S.E.C.) | 391-0381-105 |
| 3 | SEAL RETAINER FOR MOTORS ONLY | 391-3384-313 |
| 4a | PUMP LIP SEAL | 391-2883-151 |
| 4b | MOTOR UIP SEAL | 391-2883-156 |
| 5a | 2 BOLT A PILOT PUMP S.E.C. WITHOUT BUSHING TYPE 93 (3 1/4" or 82,55 mm pilot) | 326-5029-204 |
| 5b | 2 BOLT A PILOT PUMP S.E.C. WITH BUSHING TYPE 93 (3 1/4" or 82,55 mm pilot) | 326-5129-204 |
| 5c | 2 BOLT B PILOT PUMP S.E.C. WITHOUT BUSHING TYPE 96 (4" or 101,6 mm pilot) | 326-5029-203 |
| 5d | 2 BOLT B PILOT PUMP S.E.C. WITH BUSHING TYPE 96 (4" or 101,6 mm pilot) | 326-5129-203 |
| 5e | 2 BOLT A PILOT MOTOR s.E.C. WITHOUT BUSHING TYPE 93 (3 14" or 82,55 mm pilot) | 326-5029-404 |
| 5f | 2 BOLT A PILOT MOTOR S.E.C. WITH BUSHING TYPE 93 (3 14" or 82.55 mm pilot) | 326-5129-404 |
| 5g | 2 BOLT B PILOT MOTOR S.E.C. WITHOUT BUSHING TYPE 96 (4" or 101,6 mm pilot) | 326-5029-403 |
| 5h | 2 BOLT B PILOT MOTOR S.E.C. WITH BUSHING TYPE 96 (4" or 101,6 mm pilot) | 326-5129-403 |
| 5i | 4 BOLT 72 X 100 mm/ 80mm PILOT WITHOUT BUSHING TYPE 90 | 326-5033-205 |
| 5j | 4 BOLT 72X 100 mm/ 80mm PILOT WITH BUSHING TYPE 90 | 326-5133-205 |
| 5k | PAD MOUNT WITHOUT BUSHING TYPE 95 | 326--5016-202 |
| 5L | PAD MOUNT WITH BUSHING TYPE 95 | 326-5116-202 |
| 5m | 2 BOLT APILOT SEC TYPE 89 W/ SNAP RING | 326-5029-426 |
| 6a | CHECK VALVE MOTOR | 391-3681-001 |
| 6b | PRESSURE PL UG PUMP (may not be required) | 391-2286-004 |
| 7 | SHAFT BUSHING | 391-0482-195 |
| 8 | PUMP BUNA SEAL | 391-2883-168 |
| 9 | PUMP NYLON BACKUP SEAL | 391-2883-169 |
| Not Shown | MOTOR NYLON BACKUP SEAL | 391-2881-995 |
| Not Shown | MOTOR THRUST PLATE SIDE SEAL | 391-2881-997 |
| Not Shown | MOTOR THRUST PLATE END SEAL | 391-2881-996 |
| 10a | PUMP THRUST PLATE | 391-2185-063 |
| 10b | MOTOR THRUST PLATE | 391-2185-070 |
| 11a | SHAFT & GEAR SAE "A" 0.625" dia. KEYED TYPE 97 | 326-29XX-920 |
| 11b | SHAFT & GEAR SAE " A"9TOOTH SPLINE 0.609"maj. dia. TYPE 96 | 326-29XX-420 |
| 11c | SHAFT & GEAR SAE "B" 0.875"dia. KEYED TYPE 66 | 326-29XX-930 |
| 11d | SHAFT & GEAR SAE"B" 13-TOOTH SPLINE 0.858* maj. dia. TYPE 65 | 326-29XX-430 |
| 11e | SHAFT & GEAR TAPERED M12 X 1.5 THD & 3X5 KEYED TYPE 60 | 326-290X-701 |
| 11f | SHAFT & GEAR TAPERED 5/16 INTERNAL THD # WDF KEY TYPE 56 | 32629XX-604 |
| | FOR MORE INFORMATION OR SPECIAL ORDER, PLEASE CONTACT US | GENERAL NO. |
| 12a | PUMP HOUSING GASKET | 391-2881-968 |
| 12b | MOTOR HOUSING GASKET | 391-2881-429 |
| 13 | HOUSING DOWELL PIN | 391-2082-071 |
| 14a | PUMP GEAR HOUSING | 326-81XX-100 |
| 14b | MOTOR GEAR HOUSING | 326-82XX-100 |
| 15a | 315 BEARING CARRIER 1 OUTLET WITHOUT BUSHING | 326-7100-100 |
| 15b | 315 BEARING CARRIER 1 OUTLET WITH BUSHING | 326-7600-100 |
| 15c | 315 BEARING CARRIER 2 OUTLET WITHOUT BUSHING | 326-7300-100 |
| 15d | 315 BEARING CARRIER 2 OUTLET WITH BUSHING | 326-7800-100 |
| 16 | CONNECTING SHAFT | 326-1133-001 |
| 17 | GEAR SET ONLY | 326-28XX-000 |
| 18a | 315 PUMP P.E.C. NO PORTING WITHOUT BUSHING | 326-3000-100 |
| 18b | 315 PUMP P.E.C. NO PORTING WITH BUSHING | 326-3100-100 |
| 18c | 315 PUMP P.E.C. SIDE PORTING TYPE WITHOUT BUSHING | 326-3030-100 |
| 18d | 315 PUMP P.E.C. SIDE PORTING TYPE WITH BUSHING | 326-3130-100 |
| 18e | 315 PUMP P.E.C. SIDE & REAR PORTING TYPE WITHOUT BUSHING | 326-3133-100 |
| 18f | 315 PUMP P.E.C. SIDE & REAR PORTING TYPE WITH BUSHING | 326-3033-100 |
| 18g | 315 MOTOR P.E.C. PORTING TYPE WITHOUT BUSHING | 326-3020-100 |
| 18h | 315 MOTOR P.E.C. PORTING TYPE WITH BUSHING | 326-3120-100 |
| 19 | BOLTS STUDS (12"-UNC) | |
| 20 | FLAT WASHER (1/2") | 391-3782-132 |
| 21 | HEX NUT (1/2"-UNC) | 391-1451-051 |
| | | |
| P330 | |
| NO. | DESCRIPTION | GENERAL NO. |
| 1 | SHAFT BRG. SNAP RING | 391-2686-063 |
| 2a | INPUT SHAFT BRG. | 391-0381-040 |
| 2b | SPACER IN PLACE OF SHAFT BEARING | 391-3383-069 |
| 3 | SEAL RETAINER FOR MOTORS ONLY | 391-3381-040 |
| 4a | PUMP UP SEAL | 391-2883-058 |
| 4b | MOTOR UIP SEAL | 391-2883-119 |
| 4c | PUMP UP SEAL FOR CONTINENTAL SHAFT ONLY | 391-2883-107 |
| 4d | MOTOR UP SEAL FOR CONTINENTAL SHAFT ONLY | 391-2883-126 |
| 5a | 4 BOLT B PiL OT PL JMP S.E.C. WITHOUT BUSHING TYPE 42 (4" or 101,6 mm pilot) | 324-5033-201 |
| 5b | 4 BOLT B PILOT PUMP S.E.C. WiITH BUSHING TYPE 42 (4" ar 101.6 mm pilot) | 324-5133-201 |
| 5c | 4 BOLT C PILOT PUMP S.E.C. WITHOUT BUSHING TYPE 78 (5" or 127 mm pilot) | 324-5033-202 |
| 5d | 4 BOLT C PIL .OT PUMP S.E.C. WITH BUSHING TYPE 78 (5" or 127 mm pilot) | 324-5133-202 |
| 5e | 2 BOLT B PILOT PUMP S.E.C. WITHOUT BUSHING TYPE 97 (4" or 101,6 mm pilot) | 324-5023-201 |
| 5f | 2 BOLT B PILOT PUMP S.E.C. WITH BUSHING TYPE 97 (4" or 101,6 mm pilot) | 324-5123-201 |
| 5g | 2&4 BOLT B PILOT PUMPS.E.C. WITHOUT BUSHING TYPE 46 (4 or 101.6 mm pilot) | 324-5053-201 |
| 5h | 2&4 BOLT B PILOT PUMP S.E.C. WITH BUSHING TYPE 46 (4 or 101,6 mm pilot) | 324-5153-201 |
| 5i | 4 BOLT B PILOT MOTOR S.E.C. WITHOUT BUSHING TYPE 42 (4" or 101,6 mm pilot) | 324-5033-401 |
| 5j | 4 BOLT B PILOT MOTOR S.E.C. WITH BUSHING TYPE 42 (4" or 101,6 mm pilot) | 324-5133-401 |
| 5k | 4 BOLT C PILOT MOTOR S.E.C. WITHOUT BUSHING TYPE 78 (5" or 127 mm pilot) | 324-5033-402 |
| 5L | 4 BOLT C PILOT MOTOR S.E.C. WITH BUSHING TYPE 78 (5" or 127 mm pilot) | 324-5133-402 |
| 5m | 2 BOLT B PILOT MOTOR S.E.C. WITHOUT BUSHING TYPE 97 (4" or 101,6 mm pilot) | 324-5023-401 |
| 5n | 2 BOLT B PILOT MOTOR S.E.C. WITH BUSHING TYPE 97 (4" or 101,6 mm pilot) | 324-5123-401 |
| 5o | 2 &4 BOLT B PILOT MOTOR S.E.C. WITHOUT BUSHING TYPE 46 (4" or 101,6 mm pilot) | 324-5053-401 |
| 5p | 2& 4 BOLT B PIL OT MOTOR S.E.C. WITH BUSHING TYPE 46 (4" or 101 6 mm pilot) | 324-5153-401 |
| | FOR MORE INFORMATION OR SPECIAL ORDER, PLEASE CONTACT US | GENERAL NO. |
| 6a | CHECK VALVE MOTOR | 391-3681-001 |
| 6b | PRESSL JRE PLUG P MP (may mot be required) | 391-2286-004 |
| 7 | SHAFT BUSHING | 391-0482-306 |
| 8 | PUMP BUNA SEAL | 391-2883-166 |
| 9 | PUMP NYLON BACKUP SEAL | 391-2883-167 |
| Not Shown | MOTOR NYLON BACKUP SEAL | 391-2881-929 |
| Not Shown | MOTOR THRUST PLATE SIDE SEAL | 391-2881-931 |
| Not Shown | MOTOR THRUST PLATE END SEAL | 391-2881-930 |
| 10a | PUMP THRUST PLATE | 391-2185-056 |
| 10b | MOTOR THRUST PLATE | 391-2185-065 |
| 11a | SHAFT & GEAR SET 13 TOOTH SPLINE 0.858"ma. dla TYPE 25 | 324-29XX-230 |
| 11b | SHAFT & GEAR SET 0.9984* dia. KEYED (1/4" x3/8"x1 1/4") TYPE 43 | 324-29XX-740 |
| 11c | SHAFT & GEAR SET 15 TOOTH SPL INE 0.983* maj. dia TYPE 98 | 324-29XX-240 |
| 12a | PUMP HOUSING GASKET | 391-2884-050 |
| 12b | MOTOR HOUSING GASKET | 391-2884-076 |
| 13 | HOUSING DOWELL PIN | 391-2082-032 |
| 14a | PUMP GEAR HOUSING | 324-81XX-100 |
| 14b | MOTOR GEAR HOUSING | 324-82XX-100 |
| 15a | 330 BEARING CARRIER BLANK WITHOUT BUSHING | 324-7200-100 |
| 15b | 330 BEARING CARRIER BLANK WITH BUSHING | 324-7700-100 |
| 15c | 330 BEARING CARRIER 1 OUTLET WITHOUT BUSHING | 324-7100-100 |
| 15d | 330 BEARING CARRIER 1 OUTLET WITH BUSHING | 324-7600-100 |
| 15e | 330 BEARING CARRIER 2 OUTL ET WITHOUT BUSHING | 324-7300-100 |
| 15f | 330 BEARING CARRIER 2 OUTLET WITH BUSHING | 324-7800-100 |
| 15g | 330/315 BEARING CARRIER CW WITHOUT BUSHING | 324-3050-100 |
| 15h | 330/315 BEARING CARRIER CW WITH BUSHING | 324-3150-100 |
| 151 | 330/315 BEARING CARRIER CCW WITHOUT BUSHING | 324-3060-100 |
| 15j | 330/315 BEARING CARRIER CCW WITH BUSHING | 324-3160-100 |
| 16a | CONNECTING SHAFT | 324-1133-001 |
| 16b | PIGGYBACK CONNECTING SHAFT PHASE 2 | 324-1133-004 |
| 17 | GEAR SET ONLY | 324-28XX-000 |
| 18a | 330 PUMP P.E.C. NO PORTING WITHOUT BUSHING | 324-3000-100 |
| 18b | 330 PUMP P.E.C. NO PORTING WITH BUSHING | 324-3100-100 |
| 18c | 330 P.E.C. NO PORTING WITHOUT BUSHING CHECK VALVE REQ. | 324-3000-101 |
| 18d | 330 P.E.C. NO PORTING WITH BUSHING CHECK VALVE REQ. | 324-3100-101 |
| 18e | 330 PUMPP.E.C. PORTING TYPE WITHOUT BUSHING | 324-3010-100 |
| 18f | 330 PUMPP.E.C. PORTING TYPE WITH BUSHING | 324-3110-100 |
| 18g | 330 MOTOR P.E.C. PORTING TYPE WITHOUT BUSHING | 324-3020-100 |
| 18h | 330 MOTOR P.E.C. PORTING TYPE WITH BUSHING | 324-3120-100 |
| 19 | BOLTS/STUDS (5/8"-UNC) | |
| 20 | FLAT WASHER (5/8") | 391-3784-028 |
| 21 | HEX NUT (5/8"-UNC) | 391-1451-076 |
| Not Shown | CONTINENTAL SHAFT 14 TOOTH SPLINE 1.223"maj. dia. TYPE 7 | 324-1000-500 |
| Not Shown | CONTINENTAL SHAFT 13 TOOTH SPLINE 0.858"maj. dia. TYPE 25 | 324-1000-300 |
| Not Shown | CONTINENTAL SHAFT 0.9984 dia. KEYED (1/4"x 318" x1 1/4") TYPE 43 | 324-1500-400 |
| Not Shown | CONTINENTAL SHAFT 15 TOOTH SPLINE 0.983" maj. dia. TYPE 98 | 324-1200-400 |
| Not Shown | CONTINENTAL SHAFT 0.875" dia. KEYED (1/4" x 3/8" x 1") TYPE 30 | 324-1500-300 |
| Not Shown | DRIVE KEY FOR TYPE 43 SHAFT | 391-1781-082 |
| Not Shown | DRIVE KEY FOR TYPE 30 SHAFT | 391-1781-085 |
| Not Shown | CONTINENTAL SHAFT BRG. RETAINER | 312-0100-002 |
| Not Shown | CONTINENTAL SHAFT BRG. RETAINER SNAP RING | 391-2685-011 |
| | | |
| P350 | |
| NO. | DESCRIPTION | GENERAL NO. |
| 1 | SHAFT BRG. SNAP RING | 391-2686-065 |
| 2a | INPUT SHAFT BRG. | 391-0381-077 |
| 2b | SEAL RETAINER & SPACER N Pu ACE OF SHAFT BRG. | 391-3383-087 |
| 3 | SEAL RETAINER FOR MOTORS ONLY | 391-3383-020 |
| 4a | PUMP LIP SEAL | 391-2883-103 |
| 4b | MOTOR UP SEAL | 391-2883-115 |
| 4c | SEAL FOR CONTINENTAL SHAFT | 391-2883-133 |
| 5a | 4 BOLT B Moi iNT PUMP s E c. WITHOUT BUSHING TYPE 42 4 or 101.6 mm pilot) | 323-5033-201 |
| 5b | 4 BOLT B MOUNT PUMP s.E.C. WITH BUSHING TYPE 42 (4 or 101,6 mm pilot) | 323-5133-201 |
| 5c | 2/4 BOLT B MOUNT PUMP S.E.C. WITHOUT BUSHING TYPE 46 (4 or 101.6 mm pilot) | 323-5053-201 |
| 5a | 2/4 BOLT B MOUNT PUMP S.E c. WiTH BUSHING TYPE 46 (4" or 101.6 mm pilot) | 323-5153-201 |
| 5e | 4 BOLT C MOUNT PUMP S.E.C. WTTHOUT BUSHING TYPE 78 5 r 127 mm pilot) | 323-5033-202 |
| 5f | 4 BOLT C MOUNT PUMP s.E C wimH BUSHING TYPE 78 (5" or 127 mm pilot) | 323-5133-202 |
| 5g | 2 BOLT MOUNT PUMP S.EC. WTTHOUT BUSHING TYPE 97 4 or 101.6 mpilco | 323-5023-201 |
| 5h | 2 BOLT B MOUNT PUMP s.E.C. WITH BUSHING TYPE 97 (4 or 101.6 mm pilot) | 323-5123-201 |
| 5i | 2 BOLT C MOUNT PUMP s.E C WITHOUT BUSHING TYPE 9B 5 or 127 mm pilot) | 323-5023-202 |
| 5j | 2 BOLT C MOUNT PUMP s. E C. wWiTH BUSHING TYPE 98 (5 or 127 mm pilot) | 323-5123-202 |
| 5k | 4 BOLT B MOUNT MOTOR S.E.C. WITHOUT BUSHING TYPE 42 (4 or 101.6 mm pilot) | 323-5033-401 |
| 5L | 4 BOLT B MOUNT MOTOR S.E.C. WTH BUSHING TYPE 42 (4" or 101.6 mm pilot) | 323-5133-401 |
| 5m | 2/4 BOLT B MOUNT MOTOR S.E.C. WITHOUT BUSHING TYPE 46 (4* or 101.6 mm pilot) | 323-5053-401 |
| 5n | 2/4 BOLT B MOUNT MOTOR s.E.C. WITH BUSHING TYPE 46 4 cr 101.6 mm pilot) | 323-5153-401 |
| 5o | 4 BOLT C MOUNT MOTOR s.E. c. WITHOUT BUSHING TYPE 78 (5 or 127 mm pilot) | 323-5033-402 |
| 5p | 4 BOLT C MOUNT MOTOR s.E. c. WITH BUSHING TYPE 78 (5 or 127 mm pilot) | 323-5133-402 |
| 5q | 2 BOLT B MOUNT MOTOR s.E.C. WTHOUT BUSHING TYPE 97 (4 or 101.6 mm pilot) | 323-5023-401 |
| 5r | 2 BOLT B MOUNT MOTOR S.E.C. WTH BUSHING TYPE 97 (4" or 101.6 mm pilot) | 323-5123-401 |
| 5s | 2 BOLT C MOUNT MOTOR s.E.C. WITHOUT BUSHING TYPE 98 (5 or 127 mm pilot) | 323-5023-402 |
| 5t | 2 BOLT C MOUNT MOTOR S.E.C. WITH BUSHING TYPE 98 (5 or 127 mm pilot ) | 323-5123-402 |
| | FOR MORE INFORMATION OR SPECIAL ORDER, PLEASE CONTACT US | GENERAL NO. |
| 6a | CHECK VALVE MOTOR | 391-3681-001 |
| 6b | PRESSURE PLUG PUMP | 391-2286-004 |
| 7 | SHAFT BUSHING | 391-0482-308 |
| 8 | PUMP BUNA SEAL | 391-2883-140 |
| 9 | PUMP NYL ON BACKUP SEAL | 391-2883-139 |
| 10a | PUMP THRUST PLATE | 391-2185-057 |
| 10 b | MOTOR THRUST PLATE | 391-2185-068 |
| Not shown | MOTOR NYLON BACKUP SEAL | 391-2885-075 |
| Not shown | MOTOR THRUST PL ATE SIDE SEAL | 391-2885-073 |
| Not Shown | MOTOR THRUST PL ATE END SEAL | 391-2885-074 |
| 11a | SHAFT & GEAR 14 TOOTH SPUINE 1.228" maj. da. TYPE 7 | 323-29XX-250 |
| 11b | SHAFT & GEAR 1.250* KEYED (5/16") TYPE 11 | 323-29XX-750 |
| 11c | SHAFT & GEAR sET 13 TOOTH SPUNE 0.858"- maj. dia TYPE 25 | 323-29XX-230 |
| 11d | SHAFT & GEAR sET 0 9984 da. KEYED (1/4"'x3/8"x1 1/4") TYPE 43 | 323-29XX-740 |
| 11e | SHAFT & GEAR 15 TOOTH SPINE 0.980" maj dia. TYPE 98 | 323-29XX-240 |
| 11f | SHAFT & GEAR 1.250* dia. KEYED (5/16" X 5/16" x2 1/4") TYPE 73 | 323-29XX-752 |
| 12a | PUMP HOUSING GASKET | 391-2884-074 |
| 12b | MOTOR HOUSING GASKET | 391-2884-021 |
| 13 | HOUSING DOWELL PIN | 391-2082-032 |
| 14a | PUMP GEAR HOUSING | 323-81XX-100 |
| 14b | MOTOR GEAR HOUSING | 323-82XX-100 |
| 15a | 350 BEARING CARRIER B ANK WITHOUT BUSHING | 323-7200-100 |
| 15b | 350 BEARING CARRIER BLANK WITH BUSHING | 323-7700-100 |
| 15c | 350 BEARING CARRIER 1 OUTLET WITHOUT BUSHING | 323-7100-100 |
| 15d | 350 BEARING CARRIER 1 OUTLET WITH BUSHING | 323-7600-100 |
| 15e | 350 BEARING CARRIER 2 OUTLET WITHOUT BUSHING | 323-7300-100 |
| 15f | 350 BEARING CARRIER 2 OUTLET WITH BUSHING | 323-7800-100 |
| 15g | 350/315 BEARING CARRIER CW WITHOUT BUSHING | 323-3050-100 |
| 15h | 350/315 BEARING CARRIER Cw WITH BUSHING | 323-3150-100 |
| 151 | 350/315 BEARING CARRIER ccW WITHOUT BUSHING | 323-3060-100 |
| 15j | 350/315 BEARING CARRIER ccw WITH BUSHING | 323-3160-100 |
| 16a | CONNECTING SHAFT | 323-1133-001 |
| 16b | PIGGYBACK CONNECTING SHAFT PHASE 2 | 323-1133-006 |
| 16c | PIGGY BACK CONNECTING SHAFT BEARING SNAP RING | 391-2686-019 |
| 16d | PIGGY BACK CONNECTING SHAFT BEARING | 391-0381-099 |
| 160 | PIGGY BACK CONNECTING SHAFT SAE "B" SPUNE | 323-1133-003 |
| 16f | PIGGY BACK CONNECTING SHAFT SAE "A" SPUINE | 323-1133-002 |
| 17 | GEAR SET ONLY | 323-28XX-000 |
| 18a | 350 PUMP & MOTOR P.E C. WITHOUT BUSHING NO PORTING | 323-3000-100 |
| 18b | 350 PUMP & MOTOR P.E.C. WITH BUSHING NO PORTING | 323-3100-100 |
| 18c | 350 PUMP P.E.C. PORTING TYPE WITHOUT BUSHING | 323-3010-100 |
| 18d | 350 PUMP P.E.C. PORTING TYPE WITH BUSHING | 323-3110-100 |
| 18g | 350 MOTOR P.E.C. PORTING TYPE WITHOUT BUSHING | 323-3020-100 |
| 18f | 350 MOTOR P.EC. PORTING TYPE WITH BUsHING | 323-3120-100 |
| 18g | 350 P.E.C. TO S.A.E. "A" PILOT CW WITHOUT BUSHING | 323-3054-099 |
| 18h | 350 P.E.C. TO S.A.E. "A" PLOT CW wimH BUSHING | 323-3154-099 |
| 181 | 350 P.E.C. TO S.A.E. "A" PILOT CCW WITHOUT BUSsHING | 323-3064-099 |
| 18j | 350 P.E.C. TO S.A.E. "A" PILOT CCW WITH BUSHING | 323-3164-099 |
| 18k | 350 P.E.C. TO S.A.E. "B" PILOT CW WITHOUT BUSHING | 323-3054-100 |
| 18L | 350 P.E.C. TO S.A.E. "B" PILOT CW WITH BUSHING | 323-3154-100 |
| 18m | 350 P.E.C. TO S.A.E. "B" PILOT CCW WITHOUT BUSHING | 323-3064-100 |
| 18n | 350 P.E.C. TO S.A.E. "B" PILOT CCW WITH BUSHING | 323-3164-100 |
| 19 | BOLTS1 STUDS (5/8"-UNC) | |
| 20 | FLATWASHER (5/8") | 391-3784-028 |
| 21 | HEX NUT (5/8"-UNC) | 391-1451-076 |
| Not Shown | CONTINENTAL SHAF 1 250 KEYED (5/16") TYPE 11 | 323-1500-500 |
| Not Shown | CONTINENTAL SHAFT TYPE 25 (0.875"∅- 13TOOTH SPLINE) | 323-1000-300 |
| Not Shown | CONTINENTAL SHAFT TYPE 73 LONG (1 1/4"∅ KEYED 5/16") | 323-1500-502 |
| Not Shown | CONTINENTAL SHAFT14 TOOTH SPUN 228" ma..TYPE 7 | 323-1135-194 |
| Not Shown | CONTINENTAL SHAF TYE431(10000 14 x 318*x1 14 key) | 323-1500-400 |
| Not Shown | DRIVE KEY FOR TYPE 11 SHAFT | 391-1781-083 |
| Not shown | DRIVE KEY FOR TYPE 43 SHAFT | 391-1781-082 |
| Not Shown | DRVE KEY FOR TYPE 73 SHAFT | 391-1781-088 |
| Not Shown | CONTINENTAL SHAFT BRG. RETAINER | 391-3381-046 |
| Not Shown | CONTINENTAL SHAFT BRG. RETAINER SNAP RING | 391-2685-040 |
| Not Shown | CASE DRAIN PLUG | 391-2281-010 |
| | | |
| P365 | |
| NO. | DESCRIPTION | GENERAL NO. |
| 1 | SHAFT BRG. SNAP RING | 391-2688-025 |
| 2a | INPUT SHAF BRG. | 391-0381-078 |
| 2b | SEAL RETAINER & SPACER IN PLACE OF SHAFT BRG. | 391-3383-099 |
| 3 | SEAL RETAINER FOR MOTORS ONLY | 391-2584-119 |
| 4a | PUMP UP SEAL | 391-2883-052 |
| 4b | MOTOR LP SEAL | 391-2883-094 |
| 5a | 4 BOLT B MOUNT PUMP S.E.C. WITHOUT BUSHING TYPE 42 (4" or 101,6 mm pilot) | 322-5033-201 |
| 5b | 4 BOLT B MOUNT PUMP S.E.C. WITH BUSHING TYPE 42 (4" or 101.6 mm pilot) | 322-5133-201 |
| 5c | 4 BOLT C MOUNT PUMP S.E.C. WITHOUT BUSHING TYPE 78 (5" or 127 mm pilot) | 322-5033-202 |
| 5d | 4 BOLT C MOLNT PUMP S.E.C. WITH BUSHING TYPE 78(5or127 mm pilot) | 322-5133-202 |
| 5e | 2 BOLT B MOUNT PUMP S.E.C. WITHOUT BUSHING TYPE 97 (4" or 101.6 mm pilot) | 322-5023-201 |
| 5f | 2 BOLT B MOUNT PUMP S.E.C. WITH BUSHING TYPE 97 (4" or 101.6 mm pilot) | 322-5123-201 |
| 5g | 2 BOLT C MOUNT PUMP S.E.C. WITHOUT BUSHING TYPE 98 (5" or 127 mm pilot) | 322-5023-202 |
| 5h | 2 BOLT C MOUNT PUMP S.E.C. WITH BUSHING TYPE 99 (5" or 127 mm pilot) | 322-5123-202 |
| 5i | 4 BOLT B MOUNT MOTOR S.E.C. WITHOUT BUSHING TYPE 42 (4" or 101,6 mm pilot) | 322-5033-401 |
| 5j | 4 BOLT B MOUNT MOTOR S.E.C. WITH BUSHING TYPE 42 (4" or 101.6 mm pilot) | 322-5133-401 |
| 5k | 4 BOLT C MOUNT MOTOR S.E.C. WTHOuT BUSHING TYPE 78 (5" or 127 mm pilot) | 322-5033-402 |
| 5L | 4 BOLT C MOUNT MOTOR S.E.C. WITH BUSHING TYPE 78 (5" or 127 mm pilot) | 322-5133-402 |
| 5m | 2 BOLT B MOUNT MOTOR S.E.C. WITHOUT BUSHING TYPE 97 (4" or 101,6 mm pilot) | 322-5023-401 |
| 5n | 2 BOLT B MOUNT MOTOR S.E.C. WITH BUSHING TYPE 97 (4" or 101.6 mm pilot) | 322-5123-401 |
| 5o | 2 BOLT C MOUNT MOTOR S.E.C. WITHOUT BUSHING TYPE 98 (5" or 127 mm pilot) | 322-5023-402 |
| 5p | 2 BOLT C MOUNT MOTOR S.E.C. WITH BUSHING TYPE 98 (5" or 127 mm pilot) | 322-5123-402 |
| 6a | CHECK VALVE MOTOR ( Not nequirnd on a moders ) | 391-3081-001 |
| 6b | PRESSURE PLUG PUMP ( Nat requlred on all models ) | 391-2286-004 |
| 7 | SHAFT BUSHING | 391-0482-307 |
| 8 | PUMP BUNA SEAL | 391-2883-176 |
| 9 | PUMP NYLON BACKUP SEAL | 391-2883-177 |
| Not Shown | MOTOR NYLON BACKUP SEAL | 391-2885-071 |
| Not Shown | MOTOR THRUST PLATE SIDE SEAL | 391-2885-069 |
| Not Shown | MOTOR THRUST PLATE END SEAL | 391-2885-070 |
| 10a | PUMP THRUST PLATE | 391-2185-055 |
| 10b | MOTOR THRUST PLATE | 391-2185-060 |
| | FOR MORE INFORMATION OR SPECIAL ORDER, PLEASE CONTACT US | GENERAL NO. |
| 11a | SHAFT & GEAR 14 TOOTH SPLINE 1.228" maj. dia TYPE 7 | 322-29XX-250 |
| 11b | SHAFT & GEAR 1 250" KEYED (5/16") TYPE 11 | 322-29XX-750 |
| 11c | SHAF & GEAR SE 13 TOOTH SPUNE 0.858"maj. dia TYPE 25 | 322-29XX-230 |
| 12a | PUMP HOUSING GASKET | 391-2884-052 |
| 12b | MOTOR HOUSING GASKET | 391-2884-023 |
| 13a | PUMP HOUSING DOWELL PIN | 391-2082-062 |
| 13b | MOTOR HOUSING DOWELL PIN | 391-2082-069 |
| 14a | PUMP GEAR HOUSING | 322-81XX-100 |
| 14b | MOTOR GEAR HOUSING | 322-82XX-100 |
| 15a | 365 BEARING CARRIER 1 OUTLET WITHOUT BUSHING | 322-7100-100 |
| 15b | 365 BEARING CARRIER 1 OUTLET WITH BUSHING | 322-7600-100 |
| 15c | 365 BEARING CARRIER 2 OUTLET WITHOUT BUSHING | 322-7300-100 |
| 15d | 365 BEARING CARRIER 2 OUTLET WITH BUSHING | 322-7800-100 |
| 15e | 365 MOTOR BEARING CARRIER BLANK WTHOUT BUSHING | 322-7200-100 |
| 151 | 365 MOTOR BEARING CARRIER BLANK WITH BUSHING | 322-7700-100 |
| 15g | 365/330 BEARING CARRIER CW WITHOUT BUSHING | 322-3050-100 |
| 15h | 365/330 BEARING CARRIER CW WITH BUSHING | 322-3150-100 |
| 15i | 365/330 BEARING CARRIER CCW WITHOUT BUSHING | 322-3060-100 |
| 15j | 365/330 BEARING CARRIER CCW WITH BUSHING | 322-3160-100 |
| 16a | CONNECTING SHAFT | 322-1133-001 |
| 16b | PIGGYBACK CONNECTING SHAFT 365/330 | 322-1133-002 |
| 17 | GEAR SET ONLY | 322-28XX-000 |
| 18a | 365 PUMP PORT END COVER WITHOUT BUSHING NO PORTING | 322-3000-100 |
| 18b | 365 PUMP PORT END COVER WITH BUSHING NO PORTING | 322-3100-100 |
| 18c | 365 PUMP PORT END COVER WITHOUT BUSHING PORTING TYPE | 322-3010-100 |
| 18d | 365 PUMP PORT END COVER WITH BUSHING PORTING TYPE | 322-3110-100 |
| 18e | 365 MOTOR PORT END COVER WITHOUT BUSHING NO PORTING | 322-3000-099 |
| 18f | 365 MOTOR PORT END COVER WITH BUSHING NO PORTING | 322-3100-099 |
| 18g | 365 MOTOR PORT END COVER WITHOUT BUSHING PORTING TYPE | 322-3020-100 |
| 18h | 365 MOTOR PORT END COVER WITH BUSHING PORTING TYPE | 322-3120-100 |
| 18i | 365 P.E.C. TO S.A.E. "A" PILOT CW WITHOUT BUSHING | 322-3054-099 |
| 18j | 365 P.E.C. TO S.AE. "A" PILOT CW WITH BUSHING | 322-3154-099 |
| 18k | 385 P.E.C. TO S,AE. "A" PILOT CCW WITHOUT BUSHING | 322-3064-099 |
| 18L | 365 P.E.C. TO S.AE. "A" PILOT CCW WiTH BUSHING | 322-3164099 |
| 18m | 365 P.E.C. TO S.AE. "A" PILOT CW WITHOUT BUSHING | 322-3054-100 |
| 18n | 365 P.E.C. TO S.AE. "B" PILOT CW WITH BUSHING | 322-3154-100 |
| 180 | 365 P.E.C.TOS.A.E. "B" PILOT CCW WITHOUT BUSHING | 322-3064-100 |
| 18p | 365 P.E.C.TOS.A.E. "B" PILOT CCW WITH BUSHING | 322-3164-100 |
| 19 | BOLTS/STUDS | |
| 20a | MOTOR FLAT WASHER | 391-3782-114 |
| 20b | PUMP FLAT WASHER | 391-3784-028 |
| 21a | PUMP HEX NUT | 391-1451-076 |
| 21b | MOTOR HEX NUT | 391-1451-088 |
| Not Shown | CONTINENTAL SHAFT 1.250"KEYED (5/16") TYPE 11 | 322-1500-500 |
| Not Shown | CONTINENTAL SHAFT 14 TOOTH SPL INE 1.228" ma. dia.TYPE 7 | 322-1000-500 |
| Not Shown | CONTINENTALL SHAFT BRG. RETAINER | 391-3782-158 |
| Not Shown | CONTINENTAL SHAFT BRG. RETAINER SNAP RING | 391-2685-029 |
| Not Shown | SHAFT KEY FOR TYPE 11 SHAFT | 391-1781-083 |
| Not Shown | PIGGYBACK CONNECTING SHAFT BEARING | 391-0381-099 |
| Not Shown | PIGGYBACK CONNECTING SHAFTUP SEAL | 391-2883-103 |
| Not Shown | PIGGYBACK CONNECTING SHAFT BEARING SNAP RING | 391-2686-019 |
| Not Shown | 1/4" ORB DRAIN PLUG | 391-2281-010 |
Complaint
