OEM and ODM Service Offered Fixlling Infrared Photocell Sensor for Automatic Gates

Min.Order: 1

Product origin: Shenzhen, Guangdong, China

Infringement complaint:

Complaint

US$ 9 ~ 16

Description

Wireless Photocell Beam Sensor or Photo Electric Beams are basically a point to point beam of invisible infrared light that passes from a transmitting unit to a receiving unit and if an object blocks the light of infrared photocell sensor made by JUTAI you know something's there. JUTAI manufacture security Infreared photocell Sensor are used with automatic gates on either side of a driveway as a safety device to prevent a gate closing on a vehicle. Normally used when a gate is set to close by itself after a time delay automatically (auto-close). JUTAI active infrared beams (detectors)wihth Italy Quality Standards
Fixlling Infrared Photocell Sensor IR-20M made byJUTAI and used to Barrier Gate Open and Close is best solution for our customers and used in the barrier gate ,rolling shutter,automatication gate solution.

Power Supply	12/24VAC/DC
Detecting Distance	with 20m stable detection distance
Max.Range Up	20Meters(Indoor or Outdoor)
Operate Temperature	10degree-60 degree
Max.TX working Current	25mA
Max.RX working Current	35mA
Max.Relay Contract	Max 500mA e 48Vac/Dc
IP rate	IP65

Infrared Photocell Sensor Specification:
Power Supply:12/24VAC/DC
Detecting Distance: with 20m stable detection distance
Max.Range Up:20Meters(Indoor or Outdoor)
Operate Temperature:-10degree-60 degree
Max.TX working Current:25mA
Max.RX working Current:35mA
Max.Relay Contract:Max 500mA e 48Vac/Dc
IP rate: IP65
Cover Material: Anti-UV Material
Can working at outside directly;
Face to sunlight, distance not reduce
Waterproof: Water Proof and can working at outside directly
OEM/ODM: OEM and ODM service offered
Warranty Life:24 years warranty life
Net Weight:160g

Installing Infrared Photocell Sensor
Infrared Photocell Sensor Facotory suggest that for point, to point photocells, you do need a low voltage cable across the driveway. With sliding gates this is usually simply a matter of installing the cable inside the gate track, if it is hollow, although care must be taken that the cable doesn't get damaged where it enters the track and that the track doesn't have any gaps between it and the driveway large enough for the cable to slip into and be crushed by the next car that drives over it. The photocells can be installed on the gate posts and if these are hollow metal posts cabling can be run inside the post.

For swing gates, low voltage cable will need to be run along each side of the driveway as well as across the driveway. One set of photocells will need stand-alone posts.
Installing Photocells
For point, to point photocells, you do need a low voltage cable across the driveway. With sliding gates this is usually simply a matter of installing the cable inside the gate track, if it is hollow, although care must be taken that the cable doesn't get damaged where it enters the track and that the track doesn't have any gaps between it and the driveway large enough for the cable to slip into and be crushed by the next car that drives over it. The photocells can be installed on the gate posts and if these are hollow metal posts cabling can be run inside the post.

For swing gate, low voltage cable will need to be run along each side of the driveway as well as across the driveway. One set of photocells will need stand-alone posts.
Infrared Photocell Sensor IR-20M Safety To Barrier Gate Open and Close is best solution for our customers and used in the barrier gate ,rolling shutter,automatication gat solution.

Installation
1. To open the IR-20, lift the front panel of the photocell.
2. Insert the cables in their housing and fix the base to the wall. If the photocell has to be mounted on a wall, drill the three 5 ø holes and fit suitable screw anchors. If the photocell has to be mounted on metal, drill the three 3 ø holes for fitting with the self_tapping screws.
3. Make the connections. Power the photocells with a voltage can be 12-24 VAC or 12-30 VDC. If positioning, alignment and connection have been carried out properly, the red LED on the receiver will be off. Each time the ray is interrupted, the red LED switches on.
4. Cover the photocell with the front panel. Insert to the stop and close it. Interrupt the ray several times checking the relay response.
5. Fix the front panels with the provided screws.
Connection

Note:For one-to-one use: using AC and need to be shorted by the jump line hat.
Installation Diagram And Application

Size

Certification

Other type

Forward

Related products