Description
ODM OEM Universal Switching linear power supply for IP camera / phoneThe power adapter is 5W wall mounted type adapter series .
This product is adopting the input range from 100V AC to 240V AC and supplies output voltage between 5V DC and 24V DC that can satisfy the
demands for various types of DC consumer electronic devices.
You can select a different AC pin (U.S.,EU, UK, AU, Argentina) and Varied DC plug to meet custom request.
The effiency is not lower than 70% and designed accordion to UL/CE/FCC safty regulations.
Feature: Low ripple, SCP,OVP,OCP,OTP. No noticeable transformer noise or distortion adapter works, and not too hot,fire proof shell to ensure safe for use
We support semi-custom service , customized DC cable length, Dc connector are available
Black and white color available
We provide 2 years warranty
Support custom nameplates, laser nameplate
Factory direct supply, fast respond within 12 hours after received your inquire/RFQ
Application:CCTV,HDDBOX ,DVR,LED-TV,Set Top Box,POS, IP Camera, IP phone
Mini sound box, Keyboard, DVR
Robot vacuum cleaner,etc
LED strip ,LED light ,LED table lamp.
Router,amplifier,CCTV camera,hair clipper,recliner
Home appliances ,setup box ,speaker
Audio & Video equipment
Wireless communication electronics
Medical equipmentProduct pictures
Main technical parameter1.Introduction 1.
Power Supply Overview
This product has the feature such as high efficiency and high reliability, and it also has the protection function such as short-circuit protection, over voltage protection and over current protection.2 Electrical Specification 2.1 AC Input 2.1.1 Input VoltageTable 1: Lists the AC input operating voltage range. The power shall work normally and meet all electrical requirements throughout this range.
Table 1: AC Input Voltage Limitations | Minimum | Nominal | Maximum |
| 90Vac | 100-240Vac | 264Vac |
2.1.2 Input FrequencyTable 2: List the AC input operating frequency range. The power shall work normally and meet all electrical requirements throughout this range.
Table 2: AC Input Frequency Limitations | Minimum | Nominal | Maximum |
| 47Hz | 50Hz/60Hz | 63Hz |
2.1.3 Inrush Current Peak inrush current shall be limited to 50A of rated input voltage and cold start at 25 degrees C, and shall not result in a permanent damage of the power supply under any conditions of load and input voltage as specified at any input voltage as specified in table 1.2.1.4 Input Current LimitingThe input current should be less than 0.4A, under minimum AC input and full load.2.1.5 No load Input powerNo load Input power is no more than 0.1W.2.1.6 Average Efficiency The power supply according to above level VI requirement, the average efficency should be no less than 84.1% under rated input voltage 115Vac/63Hz or 230Vac/50Hz. It will be measured at the 25%,50%,75%,100% load.2.2 Output Specification 2.2.1 DC Voltage Regulation The DC output voltages will remain within the regulation ranges shown in Table 5 when measured ate the load end of the output connectors.
The voltage regulation limits do not include the transient DC load changes, which are covered in Section 3.2.4.
Table 3: DC Output voltage regulation limits| Parameter | Line Regulation | Load regulation | Cross regulation |
| 12V | ±5% | ±5.0% | N/A |
2.2.2 DC Output Current Table4: DC output current limits | Parameter | Min Current | Rate Current | Max Current | Unit |
| 1.25 | 0 | 1.25 | 1.25 | A |
2.2.3 Output Ripple and Noise The following table 5 is output ripple and noise requirements, it will be met throughout the load ranges specified in Section 2.2.2 and under all input voltage conditions as specified Section 2.1.1, Measurements will be made with an oscilloscope set to 20MHz bandwidth limit. The outputs will be bypassed with one 0.1uF multilayer (type X7R) and one 10uF tantalum electrolytic (low ESR) capacitors.
Table 5: Output ripples and noise limits | Parameter | Max. |
| 12V | 120mVp-p@25 degrees C |
2.2.4 Output Dynamic Load Response The output voltages will remain within specified regulation limit of the nominal set voltage for changes in load as specified below under the following load steps defined below table 8. At a slew rate of 0.1Amps/uS between 50Hz to 10 KHz.
Table6: Output dynamic load response limits| Dynamic Load | DC Voltage Regulation |
| 50%~100%~50% | ±10% |
2.2.5 Overshoot at turn-on/ turn-off Any overshoot at turn on or turn off shall be less than 15% of rated output voltage.2.3 Protection Function .2.3.1 Short Circuit Protection An output short circuit is defined as any output impedance of less than 0.1 ohms. The power supply will protect without damage to overseers of to the unit (components, connectors, etc) under the input conditions specified in Section 3.1 above.2.3.2 Over Current Protection The power supply shall meet the limitation requirement as below table without any damage, the unit shall recover and function automatically after the protection is removed.
Table 7: Over Current Protection limits2.4 Timing 2.4.1 Hold up Time Hold-up time no less than 5mS at 100Vac/47Hz input and no less than 10mS at 110/220Vac/50/60Hz input, the output loading should be set up with full load during the test.2.4.2 Start up Time Start up time no more than 3 seconds at 100Vac/47Hz input and no more than 2 seconds at 110/220Vac/50/60Hz, the output loading should be set up with full load during the test.3 Environment Requirement 3.1 Temperature Operating Ambient: 0ºC~ 40ºC
-10ºC~ +70ºC Non-operating Ambient: -10ºC~ +70ºC3.2 Humidity Operating: 25%~90% relative humidity (Non- condensing)
Non-operating: 10%~90% relative humidity (Non- condensing)3.3 Altitude Operating: 3000 meters
Non-operating: 3000meters4 Reliability4.1 MTBF (MIL-HDBK-217F). MTBF no less than 50K hours (25 degrees C, Full load and rated voltage input)4.2 Burn-in and Life test FINING shall discuss with customer to make sure the power in house Burn-In and life test procedures.5 Product Safety Requirement5.1Standard Meet IEC60950-1 (information technology and similar electric apparatus -safety requirement) standard requirement.5.2 Leakage Current Leakage current shall not exceed 0.25mA at 220Vac/50Hz.5.3 Insulation Resistance-Primary to Secondary: 50 Meg. Ohms min. 500VDC5.4 Dielectric Strength Testing Hi-pot test shall be met the table 8 requirements, an item listing this test as a 100% production test must be performed and be maintained at that level for a minimum of 3 seconds without failure.
Table 8: Hi-pot test | Item | Specification | Remark |
| Primary to Secondary | 3KVac | <5mA | No arcing
No broken |
| Primary to P.G | N/A | N/A |
6.Mechanical Dimensions
Europe Standard :L*W*H=55.36*40*64mm ;6.2 DC cable1.2M 5 pin cable (RJ type)Product drawingPackage and test
Complaint
