N95 Glass Fish Tank Sealing Silicone Sealant Acetoxy with FDA Certificated Food Grade

Min.Order: 10,000

Product origin: Tianjin, China

Infringement complaint:

Complaint

US$ 0.94 ~ 1.85

Description

GNS N95 GLASS PANEL SEALANT

GNS N95 GLASS PANEL SEALANT is a single-component, acetoxy cure, professional quality Glass sealant suitable for general glass and panel applications. It has very good weathering resistance, durability, sealing and bonding properties. Quick skin time for fast installation work.
FEATURES

Easy to use - one part, no mixing required. Can be dispensed with an ordinary caulking gun.
Cures at room temperature when exposed to moisture in the air.
Stable and flexible from -60ºC to +80ºC with short peak up to +205ºC.
Suitable for all kinds of glazing applications.
Outstanding weatherproofing ability, resisting to ultraviolet ray, ozone, snow, or temperature extremes.

TYPICAL USE

For Total Vision System (TVS).
Aquarium, big fish tank and general decorative usages.
Skylights, canopies and general glazing.
For butt-joints and corner joints.
For special architectural glazing.
Non-oily wood and some other construction materials. A primer may be required for optimum.

PACKAGING
Available in:
Standard Size:
300ml recyclable plastic cartridge, 24ctgs/ctn
Special Size:
Contact us for special size.
COLORS
Available for four standard colors: translucent, white, black, aluminum
Contact us for special colors.

STORAGE AND SHELF LIFE
12 months from manufacture date when store in cool dry locations below 25ºC, keep away from heat source and direct sunlight during storage.

PERFORMANCE DATA

Test Parameter	Unit	Result
As Supplied Tested at 23ºC and 50% RH
Specific Gravity	g/ml	1.00±0.02
Flow (sag or slump)	mm	0
Extrusion Rate Skin Time	ml/minute minute	100 5~10
Tack-free Time	hour	≤1.5
Curing time (5mm)	hour	≤8
As Cured-after 21 days at 23ºC and 50% RH
Durometer Hardness, Shore A	Points	33
Movement Capability	%	±25
Tensile/Modulus at 50% Elongation	Mpa	0.36
Tensile/Modulus at 100% Elongation	Mpa	0.48
Ultimate Tensile Strength Ultimate Elongation at Break	Mpa %	0.54 320

APPLICATION
Cut seal on top of cartridge. Screw on nozzle and cut the nozzle at 45°angle to the desired shape and size. For better appearance, cover outside of joint areas with masking tapes before application. Tool immediately after sealant application and remove masking tape before sealant skins
SURFACE PREPARATION
Clean all grease, dirty, water, clunky sealant from surface, accessories and protective coatings and any pollutant left inside joints and sunken parts. For best results wipe all surfaces with GNS cleaner, methylated spirits, use a lint free cloth, then wipe again with a dry lint free cloth. Detergent or soap water treatments are not recommended.
COMPATIBILITY TESTING
Incompatibility of glazing materials can lead to sealant discoloration and/ or loss of adhesion. To help protect against these problems and to ensure compatibility, GNS will also test and provide information on the compatibility of accessory materials (gaskets, spacers, etc.) and other GNS silicone sealants.

Caution
Uncured silicone can irritate eyes and skin. If contact is made with eyes, flush with water for 15 minutes and seek medical advice. Use in well ventilated area and keep out of reach for children.

LIMITATIONS

Do not use for structural glazing.
Do not use in the manufacture of Insulated Glass (IG) Units.
Not recommended for use on materials where the cure by-product (acetic acid vapor) may cause corrosion, discoloration or where the sealant may affect their appearance (eg. galvanized iron, copper, brass, zinc-coated steel, concrete, cement, brick, limestone, marble and similar highly porous stone finishes).
Do not use when substrate temperature is above 50ºC or surfaces that are wet, oily, greasy, dusty or dirty.
Do not use for sub-graded application, confined space or surfaces that require post finishes or paintings.
Do not clean or treat the sealant with materials, solvents or cleaning agents that may affect or discolor the sealant, particularly during sealant cure.
Not for permanent or continuous water immersion.
Not intended for food-contact applications.
Not recommended for use in closed or confined areas where sealant cure may be inhibited by lack of air.
Not recommended for use on polycarbonate plastic sheeting. Suitability for use on other types of plastic should be tested prior to application.

HEALTH AND ENVIRONMENTAL INFORMATION
To support Customers in their product safety needs, GNS has an extensive Product Stewardship organization and a team of Product Safety and Regulatory Compliance (PS&RC) specialists available in each area.

Forward

Related products

Acetoxy Cure Weatherproof Durability Sealing Food Grade Aquarium Glass Silicone Sealant

US$ 1.3 ~ 1.8

China Factory Directly Fish Tank Use Acetoxy Cure N95 Silicone Sealant

US$ 1.3 ~ 1.8

High Performance Acetoxy Glass Sealing Glazing Adhesion Silicone Sealant

US$ 0.7 ~ 1

Gns N95 TUV Certificated Premium Quality Glass Panel Silicone Sealant

US$ 0.94 ~ 1.85

Weatherproof Colorful Acetic Silicone Sealant Chemical Building RTV Glass Acetoxy Silicone Sealant for Glass and Door Sealing

US$ 0.58 ~ 1.2

Waterproof Acetoxy Acetic Adhesive Structural Insulating Fish Tank Aquarium Silicone Sealant

US$ 1.5 ~ 1.8

Fast Dry Silicone Sealant for Joint Sealing Fish Tank

US$ 0.95 ~ 1.6

Weatherproofing Sealant Wall Marble Glass and Ceilings Filling Sealing Acetoxy Sealant Acetic Silicone Sealant Adhesive Glue Construction Material

US$ 1.1 ~ 1.75

Customers Also viewed