Th2829c 20Hz-1MHz Automatic Component Analyzer Resistance Tester

https://ckt2017.en.made-in-china.com/product-list-1.html

Brief Introduction

By dint of leading impedance measurement technology and rich R&D experience, Tonghui continuously introduces representative impedance measurement product --- TH2829 series automatic component analyzer is another excellent product we have produced. TH2829A automatic component analyzer possesses a higher test speed, a more comprehensive analysis function and friendly human-computer interactive experience by adopting the latest high-speed processor and a new software system. Well-designed measuring circuit and optimized algorithms further enhance the test stability of low-D capacitance and high-Q inductors. The instrument is provided with 10V AC test level, 10V/100mA bias current and standalone 10V/50mA DC current, making it convenient for applying in the test of all kinds of active/ passive devices. Main/ sub parameters display, enhanced display system design, 150-points list sweep and graphical analysis capabilities of multiple parameters meet the most application requirements of customers.

Thanks to the application of a new generation of processors, the instrument has a more powerful data processing capability. The test results can be easily stored in the U disk or uploaded to the upper PC or network through multiple interfaces, promoting test automation and test efficiency.

The test frequency of TH2829A is 20Hz-300kHz.  The instrument has a test accuracy of 0.05% and highest test speed of 9ms/time. Being equipped with multiple interfaces of HANDLER, USB, LAN, RS232C, DCI, GPIB (option) as well as rich resources, the instrument will bring excellent cost performance experience for customers.

TH2829 series automatic component analyzer is completely appropriate for test requirements of all kinds of industrial and military standards.

Technical Parameter

 

Model			TH2829C
Frequency of test signal			20Hz-1MHz
	Minimum resolution		1mHz, 5-digit frequency input
	Accuracy		0.01%
Display			800×RGB×480  7-inch TFT LCD display
ACLevel	Voltage range of test signal		5mV-10Vrms
	Minimumresolution of voltage		100μV, 3-digit input
	Accuracy	ALC ON	10% x set voltage + 2mV
		ALCOFF	6% x set voltage + 2mV
	Current range of test signal		50μA-100mA
	Minimumresolution of current		1μA, 3-digit input
	Accuracy	ALC ON	10% x set current + 20μA
		ALCOFF	6% x set voltage + 20μA
DCbias voltage source	Voltage/Current range		0V- ±10V / 0mA-±100mA
	Resolution		0.5mV / 5μA
	Voltage accuracy		1% x set voltage + 5mV
	ISO ON		Be used for the bias test of inductance and transformer
AC Source impedance		ISO ON	100Ω
		ISOOFF	30Ω,50Ω,100Ωselectable
DCR Source impedance			30Ω,50Ω,100Ωselectable
DCIndependent voltage source	Voltage/current range		0V- ±10V / 0mA-±50mA
	Resolution		0.5mV / 5μA
	Voltage accuracy		1% x set voltage + 5mV
	Output resistance		100Ω
Test parameters of LCR			|Z|,Y|, C, L, X, B, R, G, D, Q, θ, DCR,Vdc-Idc
Parameter display of test page			Two sets of main/sub parameters, the second set can be set as ON/OFF;There can be 10 pages of list sweep and 15 points per page at most;Multiple parameters continuous sweep graphical analysis.
Basic accuracy	LCR test parameter		0.05%
	Calibration		Warm-up time ≥ 30 seconds;Environment temperature: 23±5ºC;  Signal voltage: 0.3Vrms-1VrmsZeroing: After OPEN or SHORT;    Length of test cable: 0 m
Measurement time(≥10 kHz)			Fast: 9 ms / timeMedium: 67 ms / timeSlow:187 ms / time Plus the refresh time of display character
Display range ofLCR parameter	Z, R ,X,DCR		0.00001Ω - 99.9999MΩ
	|Y|,G,B		0.00001μs - 99.9999s
	C		0.00001pF -  9.99999F
	L		0.00001μH -  99.9999kH
	D		0.00001 -  9.99999
	Q		0.00001 -  99999.9
	θ(DEG)		-179.999º - 179.999º
	θ(RAD)		-3.14159 - 3.14159
	Δ%		-999.999% - 999.999%
Equivalent circuit			Serial, Parallel
Range mode			Auto, Hold
Trigger mode			Internal, Manual, External, Bus
Average times			1-256
Calibration function			Open, short calibration with full frequency or dot frequency, Load
Math operation			Direct reading, ΔABS, Δ%
Delay time setup			0-999, minimum resolution: 100us
Comparator			10-bin sorting, BIN1-BIN9, NG, AUX
			Bin counter
			PASS/FAIL on front panel, LED indication
List sweep			·201 -point list sweep function ·List sweep of frequency, AC voltage/  current, internal/external DC bias  voltage/current and independent DC  source voltage can be performed on  each page. Each sweep point can be  sorted separately.
Graphical analysis			·Graph scanning and analysis of  frequency, AC level and DC bias can  be performed.·Set the sweep start point, end point  and each sweep point.·Display the maximum value, minimum  value and read any of the chosen  sweep point·Scanning graphs can be stored into  internal or external USB memory.
Internal nonvolatilememory			100 sets of LCRZ setting files memory201 times test results10 sets of GIF image, CSV data files
External USB memory			·GIF image, CSV data files·LCRZ setting files memory ·Test data can be stored via USB  memory directly.
Interface	1A bias current source		1A DC bias current source (optional) can be stalled
	I/O interface		HANDLER on rear panel
	SCI		USB,RS232C
	PCI		GPIB(optional)
	NI		LAN
	Memory interface		USB HOST(front panel)
General Specifications
Operating temperature and humidity			0ºC-40ºC, ≤ 90%RH
Power supply	Voltage		99V-121V, 198V-242V AC
	Frequency		47Hz-63Hz
Consumption			Max. 80 VA
Dimension(W×H×D)			400mm × 132mm × 385mm
Weight			Approx.13 kg

 














https://ckt2017.en.made-in-china.com/company-Changzhou-Chuangkai-Electronic-Co-Ltd-.html

 

https://ckt2017.en.made-in-china.com/contact-info.html

Chuangkai Electronic Co., Ltd is leading company specialized in producing, developing & selling various types of measuring instruments and testing equipment, such as temperature data logger, LCR meter, DC resistance tester (micro ohm meter), digital power meter, power supply, transformer tester, battery tester, programmable DC electronic load, charger, temperature controller, tachometer, high voltage signal-amplifier, power amplifier, etc.

FAQ: 
Q. How is your company's product after-sales service system?
A. The product warranty period is 12 months, we can provide lifetime maintenance. We have professional pre-sales and after-sales teams that can respond to you within 24 hours to resolve technical issues. We provide one-to-one after-sales service.

Q: Can you customize it?
A: Yes, we accept customization according to customer's specific requirements.

Q. How long is your lead time? If I want to customize instruments, how long will it take?
A. When order quantity is 1-10 units, we have ready stock goods, we can ship out within 3-5 working days after receipt of deposit; products required new production of common materials, usually the lead time is about 10-15 days; products requiring new production of special and rare materials, usually the lead time is about 20-30 days.

Q. What payment method do you accept?
A. Our company accept payment method of T/T (bank transfer), Western Union, PayPal and so on.

Q. What package do you use for your products? What shipping method do you use?
A.1. Our company use standard exporting carton for packing. 2. We ship via express courier (door to door service), by air, and by sea according to customers' requirements.

For more questions, please feel free to send inquiries to us.