Generic Compatible 10gbase-T SFP+ Copper Rj-45 30m Industrial Transceiver Module

Min.Order: 1
Product origin: Shenzhen, Guangdong, China
Infringement complaint: complaintComplaint
US$ 3 ~ 150

Description

10G Base-T Copper SFP transceiver module
Features

  1. Support 10GBASE-T Operation in Host Systems
  2. Support RX_LOS as Link indication function
  3. Hot-Pluggable SFP Footprint
  4. Compact RJ-45 Connector Assembly
  5. Compliant with SFP MSA
  6. Operating Case Temperature: 0ºC~70ºC
 

Applications

  1. 10G BASE-T IEEE 802.3an
  2. 1000BASE-T IEEE 802.3ab
  3. 100BASE-TX IEEE 802.3u
  4. 5G MGBASE-T
  5. 2.5G MGBASE-T
 

Product Description

UNSFP-10G-T, 10G BASE-T Copper Small Form Pluggable (SFP) modules are based on the SFP Multi Source Agreement (MSA). It is compliant with the 10G BASE-T, 1000BASE-T, 100BASE-TX standards as specified in IEEE STD 802.3an, 802.3ab and 802.3au.
 

Absolute Maximum Ratings*

ParameterSymbolMinTypeMaxUnits
Maximum Supply VoltageVcc-0.5 4.0V
Storage TemperatureTS-40 85°C
*Exceeding any one of these values may destroy the device permanently.
 

Normal operating condition

ParameterSymbolMinTypeMaxUnits
Operating Case TemperatureTcUNSFP-10G-T0 70°C
Supply VoltageVcc3.143.33.46V
       

 

Regulatory Compliance*Note1

Product CertificateCertificate NumberApplicable Standard
TUVR50135086EN 60950-1:2006+A11+A1+A12+A2
EN 60825-1:2014
EN 60825-2:2004+A1+A2
ULE317337UL 60950-1
CSA C22.2 No. 60950-1-07
EMC CEAE 50285865 0001EN 55022:2010
EN 55024:2010
FCCWTF14F0514417E47 CFR PART 15 OCT., 2013
FDA/CDRH 1040.10
ROHS/2011/65/EU
Note1: The above certificate number updated to June 2014, because some certificate will be updated every year, such as FDA and ROHS.
 

Electrical Characteristics

ParameterSymbolMinTypMaxUnitsNotes/Conditions
+3.3 Volt Electrical Power Interface
Supply CurrentIcc  800mA 
Input VoltageVcc3.133.33.47V 
Low-Speed Signals, Electronic Characteristics
SFP Output LOWVOL0 0.5V4.7k to 10k pull-up to host_Vcc, measured at
host side of connector
SFP Output HIGH
OH
host_ Vcc -
0.5
 host_ Vcc +
0.3
V4.7k to 10k pull-up to host_Vcc, measured at
host side of connector
SFP Input LOWVIL0 0.8V4.7k to 10k pull-up to Vcc, measured at SFP
side of connector
SFP Input HIGHVIH2 Vcc + 0.3V4.7k to 10k pull-up to Vcc, measured at SFP
side of connector
High-Speed Electrical Interface, Transmission Line-SFP
Tx Output impedanceZout,TX 100 OhmDifferential, for all frequencies between
1MHz and 125MHz
Rx Input ImpedanceZin,RX 100 OhmDifferential, for all frequencies between
1MHz and 125MHz
High-Speed Electrical Interface, Host-SFP
Single ended data
input swing
Vin250 1200mVSingle ended
Single ended data
output swing
Vout350 800mVSingle ended
Rise/Fall TimeTr,Tf 20 psec20%-80%
Tx Input
Impedance
Zin 50 OhmSingle ended
Rx Output
Impedance
Zout 50 OhmSingle ended
 

Pin Descriptions

Pin No.NameFunctionPlug Seq.Notes
1VeeTTransmitter Ground1 
2TX FaultTransmitter Fault Indication3Not used
3TX DisableTransmitter Disable31
4MOD-DEF2Module Definition 232
5MOD-DEF1Module Definition 132
6MOD-DEF0Module Definition 032
7RS0No Connection required3 
8LOSLoss of Signal3RX_LOSS
9RS1No Connection required1 
10VeeRReceiver Ground1 
11VeeRReceiver Ground1 
12RD-Inv. Received Data Out3 
13RD+Received Data Out3 
14VeeRReceiver Ground1 
15VccRReceiver Power2 
16VccTTransmitter Power2 
17VeeTTransmitter Ground1 
18TD+Transmit Data In3 
19TD-Inv. Transmit Data In3 
20VeeTTransmitter Ground1 
Notes:  
  1. PHY disabled on TDIS > 2.0V or open, enabled on TDIS < 0.8V, used to reset the module.
  2. Should be pulled up with 4.7k - 10k Ohm on host board to a voltage between 2.0 V and 3.6 V. MOD_DEF(0) pulls line low to indicate module is plugged in.Serial Communication Protocol

UNSFP-10G-T support the 2-wire serial communication protocol outlined in the SFP MSA, These SFP use a 128 byte EEPROM with an address of A0H.
 

EEPROM Serial ID Memory Contents

Accessing Serial ID Memory uses the 2 wire address 1010000X (A0H). Memory Contents of Serial ID are shown in Table 1.

Table 1 Serial ID Memory Contents

Addr.Size
(Bytes)
Name of FieldHexDescription
BASE ID FIELDS
01Identifier03SFP
11Ext. Identifier04SFP function is defined by
serial ID only
21Connector07-LC
3-108Transceiver10 00 00 00 00 00
00 00
Transmitter Code
111Encoding0664B/66B
121BR, Nominal6710.3G
131Reserved00-
141Length (9µm)km00 
151Length(9µm)100m00 
161Length (50µm) 10m0880m
171Length(62.5µm)10m0220m
181Length (Copper)00 
191Reserved1E300m
20-3516Vendor nameXX XX XX XX XX XX XX XX(note2)20 20
20 20 20 20 20 20
Vendor name (ASCII)
361Reserved00-
37-393Vendor OUIXX XX XX(note2)-
40-5516Vendor PNXX XX XX XX XX XX XX XX XX XX XX XX XX XX XX
XX(note2)
Transceiver part number
56-594Vendor revXX XX XX XX(note2)-
60-612Wavelength03 52-850nm
621Reserved00-
631CC_BASECheck Sum
(Variable)
Check code for Base ID Fields
EXTENDED ID FIELDS
64-652Options00 1ATX_DISABLE, TX_FAULT and
Loss of Signal implemented.
661BR, max00 
671BR, min00 
68-8316Vendor SNXX XX XX XX XX XX XX XX
20 20 20 20 20 20
20 20(note2)
Serial Number of transceiver (ASCII). For example "B000822".
84-918Date codeXX XX XX XX XX
XX XX XX(note2)
Manufactory date code.
For example "080405".
921Diagnostic
Monitoring Type
XX(note2)Digital diagnostic monitoring
implemented
931Enhanced OptionsXX(note2)Optional flags
941SFF_8472
Compliance
XX(note2)01 for diagnostics (Rev9.3
SFF-8472).
951CC_EXTCheck SumCheck sum for Extended ID
   (Variable)Field.
VENDOR SPECIFIC ID FIELDS
96-12732Vendor SpecificRead onlyDepends on customer
information
128-255128ReservedRead only-
        
Note2: The "XX" byte should be filled in according to practical case. For more information, please refer to the related document of SFP Multi-Source Agreement (MSA).

Order Information

Part No.Data RateMedia typeDistanceConnectorTemperature
UNSFP-10G-T* Note310GCAT6A/CAT730mRJ45Standard
Note3: Standard version.
*The product image only for reference purpose.



Product Tag:
Related categories:
Scroll to Top