Corrugated Cardboard Production Line for Corrugated Carton

1. Paper feeding: fingerless vacuum suction, with high pressure powerful draught fan. With silencer, air supply and electric control focus on the same operation counters, not less than 1.5m away from the main engine, operation side is totally closed and full guarding.
2. Engine base and wall plate: iron casting structure, thickness of the wall plate: 150mm, adopt independent speed changing box, and gimbal transmission.
3. Diameter of main corrugated roll: ¢320mm, and are made of 48CrMo alloy steel, after hardening and tempering, inner holes fine boring, NC grinding, mid frequency quenching, surface grinding, the rigidity of surface is higher than HRC58. Corrugated roll and pressure roll of pivotal section adopt heat resisting bearings which are manufactured by TWB
4. Pressure roll diameter: ¢340mm, surface are grinding and plate chrome, cylinder control up-down, raw material is 45# medium carbon steel, hardening and tempering
5. Glue wall plates adopt sliding structure, pneumatic control glue supply and glue back, diameter of the applicator glue roll : ¢242mm, surface are treated by polished and chrome plated.
6. Press roll adopt ¢160 cylinder
7. Pre-heater roll adopt seamless steel pipe which is produced by Tianjin Iron & steel group co,.ltd. Diameter ¢400mm, are all connected with metal soft pipe.

1. Working width: 2200mm
2. Operation direction: left or right
3. Design speed: 150m/min
4. Temperature scope: 160-220 C
5. Pneumatic working pressure: 0.4-0.9Mpa
6. Steam pressure: 0.8-1.3Mpa
7. Flute profile (UV type or UVV type)

1. Diameter of corrugated roll: ¢320mm
2. Diameter of pressure roller: ¢340mm
3. Diameter of applicator glue roll: ¢242mm
4. Diameter of preheater roll: ¢400mm0

1. Main frame are connected with channel steel, joist steel and angle steel
2. Both side are equipped with safe guardrail and safe herringbone pedal, the operation plate is equipped with safe escalator to ensure the safety of worker and convenient operation
3. Independent variable frequency motor lifting mechanism, PVC conveyer belt transmit, the single corrugated board from steady flute profiles.
4. Surface of all rollers are grinding and plated chrome.
5. Vacuum suction tension control, aspiration channel: 5inches, install regulation valve, the air volume can be adjusted stepless.
6. One set of electromotion correction device, correction baffle adopt double guide post positioning , lead screw drive, fix position quickly and accurate, transmit steady.
7. Electromotion control installing two group of operation plate, upper and lower bridge can be adjusted arbitrarily, it is convenient and quick
8. With high strength composite board on the whole bridge, smooth and durable, small friction, reduce the resistance of paper board transmission.

1. Working width: 2200mm
2. Operation direction: left or right
3. Height of top: 4500mm
4. Design speed: 150m/min

1. Diameter of upper paper roll and tension roll: ¢130mm
2. Diameter of paper conveyer roll: ¢180mm
3. Diameter of initiative tension roller: ¢85mm
4. Diameter of transmission paper roll and guiding paper roll: ¢111mm
5. Diameter of upper paper towing axis: ¢110mm

1. Single corrugated paper ascension motor: 3KW(variable frequency motor) 380V 50HZ continues (S1) working system
2. Overhead suction draugh fan: 3KW 380V 50HZ continues (S1) working system

1. After hardening and tempering, the surface of glue applicator roller are treated by hole precessing and special mesh snicked, paste homogeneously, less glue consumption
2. The rotation of pasting roll is controlled by variable frequency motor and frequency conversion. Controlling assure the linear speed of pasting roller be in step with double facer, also can operate independently.
3. Electromotion adjusting the glue quality, with digital display
4. Auto-circulating supply glue, can control the quantity of glue effectively, and avoid the glue deposited, good glue use and save glue
5. Surface all roll are grinded and plated chrome
6. adopt independent variable frequency motor
7. Adopt roll type encoder to measure speed signal of double facer, so as to realized data that operate in step with it.
8. The glue machine adopt human-computer interface to display, can set related data, operate conveniently and quickly
9. Can adjust the quantity of glue automatically according to the production speed, in automatic mode, can do manual fine adjustment, the operation is very convenient.
10. Electrical equipment designing and producing construction technology are according to national standard, less failure rate, easy to maintain

1. Max working width: 2200mm
2. Operation direction: left or right.
3. Design speed: 150m/min
4. Pneumatic system: 0.4-0.9Mpa

1. Diameter of pasting roll: ¢269mm
2. Diameter of doctor roll: ¢140mm
3. Diameter of lower preheater roll: ¢402mm
4. Diameter of upper preheater roll: ¢374mm
5. Diameter of transmission roll: ¢110mm

1. Surface of heating board is grinding, the width of heating board is 600mm, total 18PCS, the length of cooling case-hardened parts is 6300mm, the heating board is made of container board, according with the first class national pressure vessel standard, and provide pressure vessel certificate and inspection certificate.
2. Heating board adopt the structure of intensive heavy press shoes 
3. Up and down of the pressure roll adopt pneumatic thermal shoe type structure
4. Left-right corrective adjustment of upper transmission belt automatic adjustment, upper transmission belt consists of 2 sets of tension system, one set is manual type(fine adjustment), and another is pneumatic adjustment (quick).
5. Heat-conducting pipes of heating board control the temperature in different section and digital display the temperature
6. Upper cotton belt adopt double cylinder S type cotton belt tensioning device.
7. Lower cotton belt adopt S type manual correcting tensioning structure, concise and practical, with one set of manual fine-tuning type device.
8. Surface of driving roll is attached with wear-resisting rubber, form herringbone structure, with drum, add assure to output paperboard smooth
9. Driving parts adopt independent speed change box, wheel gear is made of ZG-500# cast steel, and wheel gear adopt oil-immersed lubrication, with liquid meter display
10. Electrical components adopts global famous brand, the device working stably and operate reliable
11. Main driving motor adopt frequency conversion energy-saving motor, low speed and big torque, wide speed-adjusting range, reliable to use and easy to maintain.
12. Inside of heating board adopt clapboard isolation structure, and let steam form S type flow direction, separate water and steam to make their functions more obviously, so as to improve the utilization rate of steam
13. Main frame adopt high-intensitive national Standard sections, firm structure, beautiful exterior, suitable to work in high speed

1. Max working width: 2200mm
2. Operation direction: left or right
3. Max speed: 150m/min
4. Temperature requirement: 160-200 ^oC   steam pressure: 0.8-1.3Mpa
5. Pneumatic pressure: 0.6-0.9Mpa
6. Length of cooling case-harden parts: 6300mm
7. Quantity of heating board: 18PCS

1. Diameter of upper driving roll: ¢860mm
2. Diameter of lower driving roll: ¢640mm
3. Diameter of front driving belt roll: ¢321mm
4. Diameter of back case-hardened driving roller: ¢215mm
5. Diameter of pressing roller: ¢70mm
6. Diameter of case-hardened carrier roll: ¢86mm
7. Diameter of upper belt tension roller: ¢130mm
8. Diameter of upper belt deviation-adjusting roll: ¢124mm
9. Diameter of lower belt tension roll: ¢130mm
10. Diameter of lower belt carrier roll: ¢130mm

1. Automatic go up and down, electric adjusting the blade distance, delta inverter control
2. The machine as an important component of corrugated cardboard to complete cutting and creasing,
3. The machine is equipped with electric axial displacement device, effective cooperation of paper offset;
4. Manually adjust the cardboard specifications, simple and practical;
5. Transmission of the synchronous belt, high accuracy
6. Thin knife cutting part adopt cutting machine, cardboard incision level off is smooth without crashing collapsing; Pneumatic sharpening; this part to achieve production process to be automatic and manual sharpening, sharpening time and clearance can be set to ensure the blade, time blade sharp.

1. Scoring speed: 150m/min
2. Max slitting width: 2200mm
3. Max slitting thickness: 11mm
4. The axial displacement: ±65mm
5. Slitting&scoring composed type:4 blade 6 scores
6. Machine dimension(mm):3000×1000×2100mm
7. Total power: 7.5KW
8. Blade diamter:φ200mm(Chengdu of china)
9. Blade thickness: ≤1.3mm
10. Min slitting width:140mm
11. Min scoring width:35mm

1. WORKING WIDTH: 2200MM
2. DESIGN DPEED: 150M/MIN
3. WORKING SPEED: 120M/MIN
4. CUTTING LENGTH RANGE: 500-9999MM
5. CUTTING PRECISION: +/- 1MM (constant speed)
6. Knife shaft diameter: φ240 mm
7. Machine wallboard width: 900mm
8. Electric power: 380V 50HZ 38A
9. Whole machine total power: 18.5KW
10. Overall dimension: 4050mm×1550mm×1920mm(LxWxH)

1. Spacial structure design, high strength mechanical wallboard and base, equipped with Perspective window on the wallboard, easy view and operation
2. Transmission system adopt oil pump auto cycle lubrication, insure transmission precision
3. Adopt high precision, high hardness gear, suitable for high speed running, long working life, insure edge of knife precision meshing, corrugated board steady no deckle edge
4. High precision knife shaft, tool rest design, high speed cutting very steady
5. All system according C.E standard design and manufacturing, after strict industrial computer testing, insure the quality of goods, long working life, more steady
6. Drive unit adopt AC servo driving, Germany KEBY driver, SHANGHAI FUTIAN motor, high quality, fast action and high precision
7. System equipped with auto detection function can prevent some problem cased by abnormal operation and mis-operation cause machine loss
8. Computer can according the size of corrugated board and production speed automatic adjusting cutting accelerated speed, auto track the production speed, keep synchronous
9. Computer can store 999 group order, and auto complete in order or according Priority Conditions
10. Cutting length: 500-9999mm, cutting precision: +/- 1mm
11. Spiral Blade made in NANJING

1. Two side wallboard and base material: HT200 casting iron
2. Upper and lower knife-shaft: 45# steel
3. Blade material: W18crv5Co5 (high speed tool steel)
4. Gear Material: 42CrMnTi fine grinding , hardening and tempering, precision up to 6 grade, sideshake small, low noise, transmission steady
5. Main driving motor(AC Servo) power: 18.5KW  2 set   
6. Paper conveying motor       power:  2.2KW 4 set ,   

1. Oil pump motor:            power   0.37Kw  2 set           
2. FLYING CUTTING SERVO CONTROL SYSTEM IS GERMANY KEB
3. ROTARY ENCODER IS REP.
4. Bearing: HRB, rolling bearing unit: zhejiang jingrun

1. Design speed: 150m/min, the stacker is controlled by computer, which can accurately calculate the number of paperboard, and can points fold and change over automatically.
2. Solve the problem of inaccurate artificial count, reduce the burden of workers, save labour, and improve the speed of the machine
3. Adopt variable frequency motor, frequency conversion control overlying transmission of paperboard, synchronize with production line automatically.
4. Adopt pneumatic baffle separation, without damage to paperboard, adopt conveyor belt to transmission the whole breadth, when reaching the scheduled quantities, the paper board will be moved out steadily
5. Backplate adopt frequency conversion closed loop controlling system, front-back, move according to the order, and adjust accurately
6. One set of paper delivery equips with 2 sets of intensive carrier roll sheet laying table.

1. OEM service are available.
2. Trade Manager online, also contact by Email.
3. To solve problems by pictures/videos.
4. Engineers are available service abroad.

PS: Normally our machines are uneasy to broken because of our 
professional machine making team and strict QC team, we will 
also send you our manual and video, what you need to do is just
learn some basic thing such as machine maintenance.

1. Are you a factory or trading company?
We are both a factory and a trading company in this field .

2. What is the terms of payment you accept?
We usually accept the T/T payment, we need 30% of total amount as deposit, 
pay the 70% balance before delivery, but we can also accept the L/C.

3. Where is your factory located ? How can I visit there?
Our factory located in Dongguang County, Hebei Province, China., near to the 
capital city Beijing and port Tianjin. You can fly to Beijing airport directly and we 
will pick you up there.

4. How does your factory do regarding quality control?
Quality is priority. We always regard great importance to quality controlling from the very small thing(even a small screw we will choose the best quality) from the beginning.

Contact Information:
If you are interested in our products,
please fell free to contact and visit me.
You are welcome all the time!
Mobil:0086 15833796236