Description
Flash Drying Equipment Description:
Spin Flash Dryer is continuous drying equipment specially designed for shaped cake, cream paste, paste slurry materials. Clean heat medium goes into the drying room from the tangent direction, form a strong rotary vortex air current together with mechanical mixer. Wet material has been added to the drying room in a fix quantity, and stir in the vortex of air currents were crushed under dry.
Flash Drying Equipment Working Principle:
The hot air enters into the bottom of the dryer in tangent direction. Under the driving of the stirrer, a powerful rotating wind area is formed. The paste state materials enter into the dryer through the s crew charger. Under the powerful function effect of stirring at high-speed roation, the materials are distributed under the function of s trike, friction and shearing force. The block state materials will soon be smashed and contact the hot air fully and the materials are heated and dried. The dried materials after the de-watering will go up with the hot-air flow.
Flash Drying Equipment Characters:
1. Drying viscous materials: The lower part of the drier is cone structure with a broken device together with the washing of wall by the air flow, which can handle a certain viscous materials.
2. Drying heat-sensitive materials: Due to the short drying time, the relative speed of the materials and the hot air is large, and the hottest air not direct contact with the dried material.
3. Drying strength: The materials in the drying process have been broken, scoured, impacted, that increasing the surface area. At the same time, the hottest air hasn't direct contact with the dried materials; therefore the inlet temperature can be higher than the melting point of materials.
4. Effective controlling of the moisture and end fineness of the materials: Through the inside settings of the drier (swirl films, elutriate ring or screener), and coordinating with the inlet air temperature, can effectively controlled the moisture and end fineness of the materials.
5. The best power matching: According to the material properties (density, bulk density, viscosity, fineness, original moisture content, residual moisture content, angle of repose, etc.), matching fans, blender, feeder, etc, so that matching the best power.
Flash Drying Equipment Application:
1. Inorganic: cryolite, ultra-fine calcium carbonate, tellurium dioxide, manganese dioxide, sodium fluoride, kaolin, zirconium silicate, salt, borax, sodium sulfate, precipitated calcium carbonate , sodium thiosulfate, zinc sulfide, sulfate, cuprous chloride, calcium hypochlorite, boric acid, borax, hydroxide, light magnesium carbonate.
2. Organic:
1. amino-anthraquinone, benzoic acid, sodium oxalate, long-chain dicarboxylic acid, lead acetate, hydroquinone, anthraquinone, sodium dichloroisocyanurate.
2. inter-stupid A nitrile, o-methyl benzoic acid, calcium citrate, sodium trichloroisocyanuric acid, sodium salicylate,
3. Acid, DSD Acid, H Acid, J Acid, R Acid, T acid, Y acid , acetanilide.
3. Polymers: PE, powdered styrene-butadiene rubber, sulfonated phenolic resins, polyvinyl chloride resins, polyvinyl acetate.
4. Dyes and Pigments: indigo, lead chromate, strontium chromate, Reactive Brilliant Blue KN-R, Li Saul red, yellow alkaline, medium black, lemon yellow, acid black 10B, Mordant black T, phthalocyanine blue, iron oxide black,
5. Medicine: Amidopyrine, protein powder, nucleotide, guanosine.
6. Pesticides: atrazine, Abamectin, Bataan, chlorothalonil, mefenacet pyridaben, imidacloprid, glyphosate, mancozeb, paclobutrazol, fenoxaprop, quizalofop-P-ethyl, methomyl, Dan sterilization, insecticide Dan, monosultap, Bisultap,
7. Chemical Agents: white carbon black, to promote the agent D, accelerator TMTD, molecular sieve, activated clay, TBSI CZ, TBSI DM, TBSI M, TBSI TMTD, TBSI ZDC, phosphate Dibasic Lead acid, stearic acid salt.
8. Food and feed additives: Soy Protein Isolate, methionine chelate copper, starch, yeast powder, glucose.
Flash Drying Equipment Technical Parameter:
Spec | Barrel diameter(mm) | Main machine dimensions(mm) | Main machine power ( kw ) | Treatmentwind capacity ( m 3 /h ) | Water evaporation quantity ( Kg/h) | Floor space (mm 2 ) |
|
XSG-2 | 200 | 250×2800 | 5-9 | 300-800 | 10-20 | 3500×2500 |
|
XSG-3 | 300 | 400×3300 | 8-15 | 600-1500 | 20-50 | 3800×2700 |
|
XSG-4 | 400 | 500×3500 | 10-17.5 | 1250-2500 | 25-70 | 4000×3000 |
|
XSG-5 | 500 | 600×4000 | 12-24 | 1500-4000 | 30-100 | 4200×3200 |
|
XSG-6 | 600 | 700×4200 | 20-29 | 2500-5000 | 40-200 | 4250×3250 |
|
XSG-8 | 800 | 900×4600 | 24-35 | 3000-8000 | 60-600 | 4500×3500 |
|
XSG-10 | 1000 | 1100×5000 | 40-62 | 5000-12500 | 100-1000 | 4750×3750 |
|
XSG-12 | 1200 | 1300×5200 | 50-89 | 10000-20000 | 150-1300 | 5000×4000 |
|
XSG-14 | 1400 | 1500×5400 | 60-105 | 14000-27000 | 200-1600 | 5250×4250 |
|
XSG-16 | 1600 | 1700×6000 | 70-105 | 18700-36000 | 250-2000 | 5500×4500 |
|
FAQ:
1. Before you inquiry, you should let us know the following information:
a.>Name of the material to be dried?
b.> Shape of the material to be dried?
c.> Initial moister of material?
d.> Final moister of material?
e.> Drying materials can withstand the maximum temperature?
f.> Capacity of dried material? kg/h (or capacity of inlet wet material? kg/h)
g.> Equipment material, stainless steel or carbon steel?
h.> Using heating source, steam / electricity / coal / heat conduction oil or other?
2. Our usual price is based on FOB Shanghai, if you request CIF, please give us the delivery port, then we will give you CIF price.
3. Our usual payment term is: 30% TT in advance, 70%TT before shipment.