Graphite Electrodes are a high-temperature resistant graphite conductive refractory material used in the metallurgical industry. Graphite Electrodes are made of needle coke, bituminous coke as aggregates, coal tar pitch as binders, after raw material calcination, crushing and milling, batching, kneading, molding, roasting, impregnation, graphitization, and machining, which are also known as artificial graphite electrodes in order to distinguish from natural graphite electrodes made of natural graphite.
Details:
Cautions:
> Be careful when transporting and pilling electrodes with a forklift and avoid a collision. One layer of goods at a time; notice the balance and alignment and avoid falling or breakage.
> When loading and unloading with a forklift, wire rope must be used and steel wrapping tape cannot be employed directly to fetch electrodes.
> Electrode should be stored in a clean and dry place. When pilling up outdoors, it should be covered with rain-proof tarpaulin and the number of piling layers ought not to exceed four.
> When using electrodes, special tools should be employed to cut the steel wrapping tape, and crane should not be adopted to avoid bursting.w3
> Steel-wire ball, metallic brush, or emery cloth is not allowed for cleaning the electrode thread, but compressed air free of oil and water is available.
> Use revolved resilient hanger and put a soft truss pad under the electrode joint to avoid breakage of the thread.
> Lift the electrode to the furnace by using a hoister with resilient hangers, and find out the center and move slowly downwards, screw and tighten with a hoop.
> If the two poles of the two electrodes are untouched or touched in overpressure, this may cause a bad effect.
> In order to avoid electrode breakage put the large materials in the lower part and small materials in the upper part.
Project | Diameter(mm) | ||||||
300-400 | 450-500 | 550-650 | |||||
YB | FC | YB | FC | YB | FC | ||
Resistivity (μΩm)≤ | Electrode | 7.0 | 6.2 | 7.5 | 6.2 | 7.5 | 6.2 |
Nipple | 6.3 | 4.3 | 6.3 | 4.3 | 6.3 | 4.3 | |
Bending Strength(Mpa)≥ | Electrode | 10.5 | 11.0 | 10.0 | 10.5 | 8.5 | 9.0 |
Nipple | 17.0 | 18.0 | 17.0 | 18.0 | 17.0 | 18.0 | |
Elastic Modulus (Gpa)≤ | Electrode | 14.0 | 9.0 | 14.0 | 9.0 | 14.0 | 9.0 |
Nipple | 16.0 | 13.0 | 16.0 | 13.0 | 16.0 | 13.0 | |
Bulk Density (g/cm³)≥ | Electrode | 1.60 | 1.67 | 1.60 | 1.67 | 1.60 | 1.67 |
Nipple | 1.72 | 1.77 | 1.72 | 1.77 | 1.72 | 1.77 | |
C.T.E(*10-6/ºC) ≥room temperature~600ºC | Electrode | 2.4 | 2.0 | 2.4 | 2.0 | 2.4 | 2.0 |
Nipple | 2.2 | 1.8 | 2.2 | 1.8 | 2.2 | 1.8 | |
Ash(%)≤ | Electrode | 0.5 | 0.3 | 0.5 | 0.3 | 0.5 | 0.3 |
Nipple | 0.5 | 0.2 | 0.5 | 0.2 | 0.5 | 0.3 |
Nominal Diameter | Allowable capacitance flow(A) | Electrice current density | |
Milimeter | Inch | ||
300 | 12'' | 13000-17400 | 17-24 |
350 | 14'' | 17400-24000 | 17-24 |
400 | 16'' | 21000-31000 | 16-24 |
450 | 18'' | 25000-40000 | 15-24 |
500 | 20'' | 30000-48000 | 15-24 |
550 | 22'' | 34000-53000 | 14-22 |
600 | 24'' | 38000-58000 | 13-21 |
650 | 26'' | 41000-65000 | 12-20 |
700 | 28'' | 45000-720000 | 12-19 |
Henan calgon Carbon Co., Ltd. is located in Anyang City, Henan Province, which is known as "the ancient capital of the Seven Dynasties of China" and "the center of Chinese civilization". It is the largest international export enterprise focusing on the export of graphite electrodes in China.
After years of operation and development,Henan calgon carbon co., LTD has became into the professional inspection center, r&d center, the application of new technology center, with China's conformity assessment (CNAS) national approval. In 1999, it passed the ISO9000 quality assurance system certification; in 2010 we passed the quality management, Environmental management, occupational health management "three system" certification.
Certificates
We cooperate with the top 9 graphite electrodes manufacturer in China, we provide the best quality with best price.
Besides, we have been exported the graphite electrodes for more than 10 years, we have accumulated a lot of experience and can solve various problems.
Choose us, you will never be let down!!!
Q: What information should I let you know if i want to get a quotation?
A: The required material dimension (diameter*length; if possible, please kindly supply us drawings).
If it is possible, please also provide the application of products, we will recommend the most suitable products with details for confirmation.
Q: How can you control your quality?
A: For each production processing, We have a complete QC system for the chemical composition and physical properties. After production, all the goods will be tested, and the quality certificate will be shipped along with goods.
Q: What is your lead time?
A: It usually needs about 15- 20 days after receiving the PO.
Q: What are your payment terms?
A: We can accept a 30% deposit, 70% balance to be against the BL copy or by LC, or other payment terms. (according to your order value)
Q: Can we visit your company?
A: Yes, for sure, It's my pleasure to visit Our company.
Q: What is the shipping cost?
A: The shipping cost is determined by the destination port, weight, packing size, total CBM of the products, we will try best to get the most reasonable shipping cost from the forwarders or express couriers to help you save more money.