Complaint
| General | ||||
| Form | Resin Pellets | |||
Feature | Biocompatible Steam Sterilization X-Ray Sterilizable | Medical Disinfection Application Low Flow | Gamma Sterilizable E-Beam Eto Sterilization | |
| Usage | Appliances Medical | Fluid Handling | Oil/Gas Applications | |
| Physical | Nominal Value | Test Method | ||
| Density / Specific Gravity | 1.20 g/cm³ 1.19 g/cm³ | ASTM D792 ISO 1183 | ||
| Melt Mass-Flow Rate, MFR | ASTM D1238 | |||
| 300 °C;1.2 kg | 5.0 g/10min | |||
| 300 °C;5 kg | 24 g/10min | |||
| Melt Volume-Flow Rate, MVR(300 °C;1.2 kg) | 5.00 cm³/10 min | ISO 1133 | ||
| Molding Shrinkage, Flow, Tensile Bar | 0.50 - 0.70 % | Internal Method | ||
| Molding Shrinkage, Across Flow(3.2 mm) | 0.50 - 0.70 % | Internal Method | ||
| Molding Shrinkage, Flow(3.2 mm) | 0.50 - 0.70 % | Internal Method | ||
| Water Absorption(24 hr) | 0.14 % | ASTM D570 | ||
| Water Absorption, Saturation(23 °C) | 0.26 % | ISO 62 | ||
| Water Absorption, Equilibrium(50% RH;23 °C) | 0.10 % | ISO 62 | ||
| Mechanical | Nominal Value | Test Method | ||
| Tensile Modulus | ||||
| 50 mm/min | 2270 MPa | ASTM D638 | ||
| 2450 MPa | ISO 527-2/1 | |||
| Tensile Strength, Yield | ||||
| 50 mm/min;Type I | 62.0 MPa | ASTM D638 | ||
| 61.0 MPa | ISO 527-2/50 | |||
| Tensile Strength, Break | ||
| 50 mm/min;Type I | 72.0 MPa 71.0 MPa | ASTM D638 ISO 527-2/50 |
| Tensile Elongation, Yield | ||
| 50 mm/min;Type I | 6.5 % 5.9 % | ASTM D638 ISO 527-2/50 |
| Tensile Elongation, Break | ||
| 50 mm/min;Type I | 130 % 130 % | ASTM D638 ISO 527-2/50 |
| Flexural Modulus | ||
| 1.3 mm/min;50 mm;Span | 2340 MPa | ASTM D790 |
| 2 mm/min | 2200 MPa | ISO 178 |
| Flexural Stress, at Yield(2 mm/min) | 95.0 MPa | ISO 178 |
| Flexural Stress, Yield(1.3 mm/min;50 mm;Span) | 100 MPa | ASTM D790 |
| C harpy Notched Impact Strength -30 °C;80 23 °C;80 | 15 kJ/m² 75 kJ/m² | ISO 179 1eA |
| C harpy Unnotched Impact Strength -30 °C;80 23 °C;80 | No Break No Break | ISO 179 1eU |
| Notched Izod Impact | ||
| -30 °C | 790 J/m | ASTM D256 |
| 23 °C | 940 J/m | ASTM D256 |
| -30 °C;80*10*3 mm | 15 kJ/m² | ISO 180/1A |
| 23 °C;80*10*3 mm | 75 kJ/m² | ISO 180/1A |
| Unnotched Izod Impact | ||
| 23 °C | 2700 J/m | ASTM D4812 |
| -30 °C;80*10*3 mm | No Break | ISO 180/1U |
| 23 °C;80*10*3 mm | No Break | ISO 180/1U |
| Instrumented Dart Impact, Total Energy(23 °C) | 82.0 J | ASTM D3763 |
| Thermal | Nominal Value | Test Method |
| Deflection Temperature Under Load, Unannealed | ||
| 0.45 MPa;3.2 mm | 141 °C | ASTM D648 |
| 0.45 MPa;6.4 mm | 141 °C | ASTM D648 |
| 1.8 MPa;3.2 mm | 129 °C | ASTM D648 |
| 1.8 MPa;6.4 mm | 132 °C | ASTM D648 |
| 80*10*4 mm;1.8 MPa;4 mm;64 mm;Span | 128 °C | ISO 75-2/Af |
| Vicat Softening Temperature | ||
| 50 °C/h;50 N;Rate A;Loading 2 | 145 °C 146 °C | ISO 306/B50;ASTM D1525 ISO 306/B120 |
| Ball Pressure Test(73 - 77 °C) | Pass | IEC 60695-10-2 |
| CLTE, Flow(-40 - 40 °C) | 6.6E-5 cm/cm/°C | ASTM E831;ISO 11359-2 |
| CLTE, Transverse | ||
| -40 - 40 °C | 7.5E-5 cm/cm/°C | ASTM E831 |
| -40 °C | 7.5E-5 cm/cm/°C | ISO 11359-2 |
| Processing | Nominal Value | |
| Drying Temperature<Injection> | 120 °C | |
| Drying Time<Injection> | 3.0 - 4.0 hr | |
| Suggested Max Moisture<Injection> | 0.020 % | |
| Suggested Shot Size<Injection> | 40 - 60 % | |
| Rear Temperature<Injection> | 290 - 310 °C | |
| Middle Temperature<injection> | 300 - 320 °C | |
| Front Temperature<Injection> | 310 - 330 °C | |
| Nozzle Temperature<Injection> | 305 - 325 °C | |
| Processing Temp, Melt<Injection> | 310 - 330 °C | |
| Mold Temperature<Injection> | 80 - 115 °C | |
| Back Pressure<Injection> | 0.300 - 0.700 MPa | |
| Screw Speed <Injection> | 40 - 70 rpm | |
| Vent Depth <Injection> | 0.025 - 0.076 mm | |
| Drying Time, Cumulative<Injection> | 48 hrs |
