Description
GNS N95 GLASS PANEL SEALANT Product Description
GNS N95 GLASS PANEL SEALANT is a single-component, acetoxy cure, professional quality Glass sealant suitable for general glass and panel applications. It has very good weathering resistance, durability, sealing and bonding properties. Quick skin time for fast installation work.
Detailed Photos
FEATURES - Easy to use - one part, no mixing required. Can be dispensed with an ordinary caulking gun.
- Cures at room temperature when exposed to moisture in the air.
- Stable and flexible from -60ºC to +80ºC with short peak up to +205ºC.
- Suitable for all kinds of glazing applications.
- Outstanding weatherproofing ability, resisting to ultraviolet ray, ozone, snow, or temperature extremes.
TYPICAL USE- For Total Vision System (TVS).
- Aquarium, big fish tank and general decorative usages.
- Skylights, canopies and general glazing.
- For butt-joints and corner joints.
- For special architectural glazing.
- Non-oily wood and some other construction materials. A primer may be required for optimum.
PACKAGINGAvailable in:
Standard Size:
300ml recyclable plastic cartridge, 24ctgs/ctn
590ml aluminum sausage, 20ssgs/ctn
Special Size:
Contact us for special size.COLORS Available for four standard colors: Translucent, White, Black, Aluminum.
Contact us for special colors.STORAGE AND SHELF LIFE12 months from manufacture date when store in cool dry locations below 25ºC, keep away from heat source and direct sunlight during storage.Installation Instructions
| Test Parameter | Unit | Result |
| As Supplied Tested at 23ºC and 50% RH |
| Specific Gravity | g/ml | 1.00±0.02 |
| Flow (sag or slump) | mm | 0 |
Extrusion Rate
Skin Time | ml/minute
minute | 100
5~10 |
| Tack-free Time | hour | ≤1.5 |
| Curing time (5mm) | hour | ≤8 |
| As Cured-after 21 days at 23ºC and 50% RH |
| Durometer Hardness, Shore A | Points | 33 |
| Movement Capability | % | ±25 |
| Tensile/Modulus at 50% Elongation | Mpa | 0.36 |
| Tensile/Modulus at 100% Elongation | Mpa | 0.48 |
Ultimate Tensile Strength
Ultimate Elongation at Break | Mpa
% | 0.54
320 |
APPLICATIONCut seal on top of cartridge. Screw on nozzle and cut the nozzle at 45°angle to the desired shape and size. For better appearance, cover outside of joint areas with masking tapes before application. Tool immediately after sealant application and remove masking tape before sealant skinsSURFACE PREPARATIONClean all grease, dirty, water, clunky sealant from surface, accessories and protective coatings and any pollutant left inside joints and sunken parts. For best results wipe all surfaces with GNS cleaner, methylated spirits, use a lint free cloth, then wipe again with a dry lint free cloth. Detergent or soap water treatments are not recommended.COMPATIBILITY TESTINGIncompatibility of glazing materials can lead to sealant discoloration and/ or loss of adhesion. To help protect against these problems and to ensure compatibility, GNS will also test and provide information on the compatibility of accessory materials (gaskets, spacers, etc.) and other GNS silicone sealants.CautionUncured silicone can irritate eyes and skin. If contact is made with eyes, flush with water for 15 minutes and seek medical advice. Use in well ventilated area and keep out of reach for children.LIMITATIONS- Not recommended for use on structural application.
- Do not use in the manufacture of Insulated Glass (IG) Units.
- Do not use when substrate temperature is above 50ºC or surfaces that are plasticizers, oily, greasy, dusty or dirty.
- Do not use for painted surfaces, otherwise may cause seal failure as the paint cracking or paint stripping.
- Do not use for confined space or surfaces that require post finishes or paintings.
- Do not clean or treat the sealant with materials, solvents or cleaning agents that may affect or discolor the sealant, particularly during sealant cure.
- Not for fireproofing seal system.
- Not for frost-laden or wet surfaces.
- Not intended for food-contact applications.
Company Profile
Gunuo (Tianjin) Industrial Co., Ltd. is a group of company in China which specializes in PU foam, silicone sealant, acrylic
sealant, PU sealant, adhesive and so on. We have two manufacturing plants located in Tianjin and Foshan China. Our factory covers
200,000 square meters with 32 advanced full automatic PU foam production lines. We produced and sold out more than 160 million
cans in 2018 with 55% market share. Our annual silicone sealants production capability is 20000 tons. Our products meet American
Standard, European Standard, China Standard and some other International Standards.
FAQ
1. who are we?
We are based in Tianjin, China, start from 2010,sell to Domestic Market(90.00%),Mid East(3.00%),South America(2.00%),Southeast
Asia(2.00%),Africa(00.00%),Oceania(00.00%),Northern Europe(00.00%). There are total about 301-500 people in our office.
2. how can we guarantee quality?
Always a pre-production sample before mass production;
Always final Inspection before shipment;
3.what can you buy from us?
PU Foam/Silicone Sealant/Other Adhesion Products
4. why should you buy from us not from other suppliers?
Biggest PU Foam factory in Asia with 32 advanced full automatic production lines. 19 years manufacturer; 55% market share of PU
foam in China.
5. what services can we provide?
Accepted Delivery Terms: FOB,CFR,CIF,EXW;
Accepted Payment Currency:EUR,AUD,HKD,CNY;
Accepted Payment Type: T/T,L/C,D/P D/A,Western Union,Cash,Escrow;
Language Spoken:English,Chinese,Spanish,Japanese,Portuguese,German,Arabic,Russian,Hindi,Italian
Complaint
