Ogx20 Electric Ball Valve with AC220V Two-Way DN25

Min.Order: 50
Product origin: Wenzhou, Zhejiang, China
Infringement complaint: complaintComplaint
US$ 23 ~ 30

Description
OGX2071 Electric ball valve Instruction manual

Product Introduction
The OGX2071 series on-off electric valve consist of a valve actuator and a brass valve.This product can be used to control the opening and closing of cold and hot water air conditioning system pipes,in order to achieve the purpose of controlling the room temperature.The actuator is driven by a one-way hysteresis synchronous motor and the valve is closed when not operating.When the product needs to work, the temperature controller provides an opening signal, so that the electric valve is connected to the AC power supply to open the valve, frozen water or hot water into the fan coil, to provide cold air or heating for the room.When the room temperature reaches the set value of the temperature controller, the temperature controller will power off the electric valve, and the reset spring closes the valve, so as to cut off the water flow into the fan coil.The valve is closed or opened to keep the room within the temperature range set by the thermostat at all times.

Scope Of Application
This product is suitable for petrochemical industry, sewage treatment, paper making industry, indoor heating system, air conditioning system, floor heating system, solar energy exhaust system and other systems.

Working Conditions
Rated voltage AC220V 50-60Hz power supply use,working environment temperature at room temperature (25°C), lower temperature is allowed to have higher relative humidity, such as 90% at + 25ºC.

Product Features
  1. Protection level IP40 
  2. It can be controlled manually controlled during system debugging and maintenance.
  3. During installation,it takes up little external space and has an eccentric structure,which can be installed close to the wall.
  4. Corrosion resistance,long life,and small size
  5. Convenient installation and easy maintenance
  6. The noise of the product is low.
  7. The valve will close after power failure.
  8. The product can be quickly connected and easy to load and unload.
  9. The actuator can be assembled in 2 directions, making it easier to wire and maintain.

Model Meaning

Technical Parameter 
Supply voltageAC220V  50-60HZPower consumption6W
Itinerary3mmProtection levelIP40
Medium temperature2ºC~95ºC(liquidity)Control modeTwo lines and one control
Work environment2ºC~60ºCThrust10Kg
Lead length10cmActuator size66*75*73mm
Valve body specificationsDN15,DN20,DN25  

Diagram

Instructions for use
This product can work reliably at 85% -110% of the rated working voltage.
When installing and wiring the product, the wiring should strictly follow the diagram below. It should be confirmed that the product is installed in place, the wiring is correct, and the contact part of the wire should be checked for firmness, compression, and looseness to ensure safe use.
During the use of the product, regular general inspections should be conducted (such as every six months of operation) to test the normal switching switch product and check whether the product operates normally.
During general maintenance or repair of the product, it must be ensured that the product is not electrified; After maintenance or repair is completed, turn on the power supply to restore normal working status.


Wiring diagram

Fault analysis
Fault phenomenonCause analysisExclusion methodRemarks column
Does not operate after power on.The wires are not connected in place, resulting in poor contact.Check the power supply status of the power supply port and connect the wires in place. 
Incorrect connection to power and voltage usage.Connect the correct power supply and voltage.If the power connection is incorrect and the product is burned, the consequences will be borne by oneself.

Overall dimensions

Transportation and storage
The product should not be subjected to severe impact during transportation and unpacking, and should be transported and stored in accordance with GBT 13384-2008 "General Technical Conditions for Packaging of Mechanical and Electrical Products".
Inventory and storage should be stored on racks under the original packaging conditions, and the stacking height should not exceed 6 layers. The storage area should be clean, with an ambient temperature of 0-40 ºC, a relative humidity of not more than 85%, and no harmful substances that can cause corrosion in the air.


Quality assurance
The product is guaranteed for 2 years from the date of sale.
Under the correct storage, installation, and use, the company guarantees that the product will function normally during the warranty period. If damage or malfunction occurs due to poor manufacturing quality during this period, the company shall be responsible for replacement or repair.




Reminder: Please communicate with us the type of specifications you need before placing the order. If we are unable to reply to you in time due to time difference, please understand. Thank you for your choice and understanding!I wish you a happy life!
Product Tag:
Related categories:
Scroll to Top