1:Inner and outer tank automatic feeding relatively flat counting length shearing machinery line
The series lines consisting of feeding machine, decoiling drive of the leveling,counting&laminating actions driven &shearing machine. The material 1-4 control by PLC, adjust arbitrarily, easy operation, counting assurate,save the time and labor. Is the indispensable machine in the fields of the solar ans cooperage industry.
1. Model:TX-001
2.Rated voltage:380V
3. Rated Power:8KW
4.Processing plate thickness(mm):0.31-0.5
5. Processing plate Width(mm):0-1200
6. Shear length range: Adjustable
7.Leveling Accuracy(Mpa):1-2mm
8.Shear length and precision:0.5mm/M
Use delta PLC control system and servo motor drive, electric part is the CHNT electric, pneumatic element is AIRTAC. The electric part warranty period is one year.
2. Open type automatic TIG welding machine
Specification:2500mm
I.Performance describe:
One:running conditions
1.Barrel diameter:310-800mm
2.Workpiece thickness:0.31-0.5mm
3.Maximum barrel length:L=2500mm
4.Material: stainless steel gavalized steel
II:machine configuration
1.L2500mmlongitudinal seam welding machine(ncluding: the cooling article copper welding car electric control system).
2.WSM-160D inverter, and pulse, digital welder 1 set
3.automatic welding torch 1 set
4.with protection system, water cycle cooling system.
5. transmission parts is the top of the Taiwan silver linear guide.
6, all electrical programm is imported.
7.divided into domestic CHNT electrical appliances.
8.electrical parts warranty period of one year.
9.pneumatic components for the Airtac.
III:technical parameters, requirements
1. rated voltage: 220 VAC frequency 50 HZ
2. the power rating: 5.5 KVA
3. welding seam straight length: 2500 mm
4. welding seam thickness straight effective: 0.31-- 1.2 mm
5.the welding diameter: 310-800 mm
6. compressed air: 0.45 Mpa
7. welding speed: stepless continuous adjustable
8.welding quality: one-side welding, double forming, weld plane, even and bright is strictly prohibited, partial welding, porosity appear welding leakage, oxidation slag etc.
9.shear linear error is not more than 0.03 mm/m, connecting the noodles is burr, welding seam of seamless straightness shall not be longer than 0.05 mm/m
3. L1500mm water nozzle tig welding machine
I :working condition
1.Tank diameter: 310-800 mm
2.The thickness of work piece:1-2 mm
3.Materials: stainless steel gavalized steel
II: configuration
1, KR-350 welding machine and wire device
2, automatic welding torch 1 set.
3, have water cycle cooling system.
4, transmission parts for the top of the Taiwan silver linear guide.
5, electrical programming to all the imported.
6, divided into domesticCHNT or renmin electrical appliances.
7, electrical parts warranty period of one year.
8, pneumatic components for the Airtac.
III, technical parameters
1.Rated voltage: 380 VAC50HZ
2.power rating: 16.2KVA+0.75KVA
3.Compressed air: 0.45 Mpa
4.Cooling water: tap water or small water pump
5.Special advantages: weld pool and beautiful, high efficiency, low cost, is the ideal equipment of bucket of industry, the solar energy water heater, electric water heater industry
6.random distribution of three sets of mould in the specified specifications
4. Air pressure type automatic inner tank edge beading machine
type:2500mm
Performance describe:
I:work conditions
1.According to various size mold with corresponding work flanging, both sides simultaneously.
2.Barrel diameter:310-600mm
3.Workpiece thickness:0.31-0.5mm
4.Maximum barrel length:L=1500mm
5.Revers height≤8mm
6.Material :stainless steel,gavalized steel
7.provide 2 sets mold that customer need with machine together.
8.provide two sets input and output working line
II,technical parameters,requirement
1.Rated voltage:380VAC 50HZ
2.Rated power:1.5KVA
3.Compressed air pressure:0.45Mpa
4.Electric part warranty period one year.
5.Pneumatic element:cylinder stator,solenoid valve,clutch pneumatic element made by AIRTAC.
6.The device use manipulator,servo system,stepping motor three in one automatic feeding and laying of the material
5. Air pressure automatic strength equipment-inner tank
Type :2500mm
Performance describe:
I:work conditions
1.Barrel diameter: 310-800mm
2.Workpiece thickness:0.31-0.5mm
3.Maximum barrel length:L=2500mm
4.Material :stainless steel,gavalized steel
II .technical parameters,requirement
1.Rated voltage:380VAC 50HZ
2.Rated power:1.5KVA
3.Strength height/width:according to customer requirements,if no special requirements, according to conventional solar reinforced production requirements.
4.compressed air pressure:0.45mMpa
5.Electric part warranty period one year.
6.Pneumatic element:pneumatic element made by AIRTAC.
7.The device have the automatic stop function (is time fixed position )
8.Pneumatic liner pulse seam welding machine
6. Circular pulse seam welding machine
Type :35KVA
I .technical parameters,requirement
1.mode:FIN-35KVA
2.rated capacity:35KVA
3.secondary voltage adjustable range:2.0V-3.8V
4.Rated duty cycle:75%
5.The maximum welding thickness:0.31-0.5mm
6.Welding speed:Continuous adjustable stepless
7.Compressed air pressure(Mpa):0.45
8.Electric part warranty period one year.
9.Pneumatic element:pneumatic element made by AIRTAC
10.The device automatic turning etc characteristic
7. Open type--go up and down rolling machine
Type :2500mm
performance:
1.the rolling workpiece:
2.diameter:Φ=310~600mm
3.workpiece thickness:δ=0.31-0.5mm
4.maximum barrel length:L=2500mm
5.Material :stainless steel,gavalized steel
6.Rated voltage:380VAC 50HZ
7.Rated power:1.5KVA
8.Compressed air pressure :0.45Mpa
9.Electric part warranty period one year.
10.Pneumatic element:pneumatic element made by AIRTAC.
11.The device accommodation rang 0.31-1.2mm, is the non-pressure solar water heater and tank ideal equipment.
8. Automatic inner tank tube hole flatting machine----open type
type:2500mm
performance:
I,working condition
1.Barrel diameter:310-600mm
2.Working thickness:0.31-0.5mm
3.Maximum working length:L=2500mm
4.Material :pearl plate,aluminizing zinc,stainless steel,Fluorine titanium plate etc
II,technical parameters,requirement
1.Rated voltage:380VAC 50HZ
2.Rated power:0.5KVA
3.Height/width:according to customer requirements, if no special requirements, according to conventional production requirements.
4.Compressed air pressure:0.45mMpa
5.Electric part warranty period one year.
6.Pneumatic element:pneumatic element made by AIRTAC
The device use for solar water heater tank tube hole to make dabber on the two sides, Will the solar e water heater inside bucket of vacuum tubes hole in a plane, make the vacuum tube hole 2-3 points increased strength, in the operation not make the pipe hole deformation, reduce scrap, sheet bending place does not produce indentation, need not special mold, use cost is low, installation and operation are convenient, has the very high plane degrees.
9. Water leakage checking equipment .
Size :2500mm
Performance
Water heater leakage of the water tank machine is placed in the tank to test platform, completes the initial preparation, all accurate after, began to fill detection, through the set certain promptly after the pressure, the tank of water tank of gas tightness test whether a flat? If have a bubble? To perceive accurately specific a flat position. According to the test results workers do the further processing; Or into the next working procedure. In this cycle.
1.Rated voltage : 220VAC 50HZ
2.Rated power:1,5KVA
3.Overall dimension: 3400mm×2000mm×2600mm
4.Compressed air: 0.45Mpa
5.Cylinder under pressure range: 0 ~ 800mm
6.Drive cylinder range: 0 ~ 700mm
7.Using Taiwan linear guide and the cylinder
8.Electric parts ,CHNT
9.Maintenance time : one year
10.Pneumatic components is AIRTAC.
The device has a self-plug, move, under the pressure back to the origin, unloadingplug function, duplex and single-station selection, fast, efficient, less labor and so on.
10. Water heater turret punching machine
type:working station
performance:
I,c-type double frame fuselage, the machine by advanced tempering treatment, eliminate stress, to ensure the machine accuracy of the long-term stability, maximum limit increases the machine tool and mold die life
II, the advanced mold structure, make plank of blunt turn, extension, flatten easier to implement process requirements
III, to the positioning structure turntable, effectively improve the accuracy of the turntable and life, have6, 8, 10, 12 and so on the different work station can chose.
IV, using international standards nc code programming, to run automatically or manually move, the simulation of operation, emergency stop, fault the automatic alarm.
11. Automatic bending and locking machine
This equipment is a new-type occlusion device for occluding tank unwedded. It uses belt transmission, and has advanced technology and elegant shape. Besides, the occlusion is regular, and its strength and speed are high. It allows processing barrel of different diameters in just one machine, so production costs can be greatly reduced.
1.Cylinder diameter :diameter 310-600mm
2.Working thickness:0.31-0.5mm
3.The maximum cylinder length:L=3000mm
4.Grooving groove radius of ≤1.5mm(special specification like custom)
5.Material : pearl plate, galvanized, stainless steel , titanium ,etc…
12. Automatic outer tank necking machinery line .
type:2500mm
Performance
I :working condition
1.Cylinder diameter :diameter 310-600mm
2.Working thickness:0.31-0.5mm
3.The maximum cylinder length:L=2500mm
4.Grooving groove radius of ≤1.5mm(special specification like custom)
5.Material : pearl plate, galvanized, stainless steel , titanium ,etc…
I.Technical parameter ,requirement ,
1.Rated voltage:380VAC 50HZ
2.Rated power :4KVA
3.Necking height / width: according to customer requirements, if no special requirements, according to conventional production requirements.
4.compressed air pressure: 0.45mMpa
5.The Pneumatic components :cylinder, solenoid valve ,is from AIRTAC
III.The device use manipulator,servo system,stepping motor three in one.
It is a new fillet-forming and reducing device with engaging gear assembly used for machining reducing end with taper,which has advantages such as beautiful figure,mean reducing size and high strength for the formed product,and for the device itself, the advanced property embodies that different diameters outer-barrels are available to be machined by one device, various material including SS plate,sheet zinc with aluminum plated, color plate etc being machined without mould replacement, which shall reduce the production costs.
13. U -type , puf working line
Type :60 station
Non-pressure ,puf process, - clean -package process: U-type puf working line (include puf machine ,puf stooper,) - cover machine , -clean package line.
Performance :
Production line for 30-85 working position (to be confirmed groud rail station solar cycle foaming production line, the U-shaped by the motor drive the speed reducer. The production line is mainly composed of manual clamping, manual jam. Circular drive. ,(fixture clamping ) manual filling, heating cycle, manual and curing the next bubble, and other processes of the composition. The production lines can be continuous work, can also be action cycle to work. Step-by -step with compact structure , simple operation . smooth transmission, high production efficiency . it is widely used in batch production of solar -energy foam .
1, filling in the form: vertical manual filling.
2, filling media: POL + ISO (CFC11 or HCFC141b).
3,Working speed, about 60second ,(depending on worker , proficiency)
4:working station :60
5, the gas capacity: 1 / 2 "(0.5MPa)
6, oven temperature: 50 ºC ± 10 ºC
7, capacity: about 50KW (380V, 50HZ)
8, the curing time: ≥ 20min
9, electrical programming is imported.
10.electric parts ,CHNT ,
11, electrical parts warranty for one year.
1. Ratio of raw material: 1:1 fixed
2. Viscosity range of raw materials: 200-1000CPS(under the operation temperature)
3. Output quantity of raw materials: 4-8 Kg/min
4. Operating temperature: 0ºC-65ºC
5. Cleaning style of spray gun: high-pressure mechanical cleaning
6. Drive mode: hydraulic drive
7. Maximum system pressure: 21Mpa
8. Working hydraulic pressure: 6-8Mpa
9. Power: three phase 380V 50HZ 20A
10. Power of raw material heater: 1250Wx2
11. Length of heating and insulation pipe: 8000mm
12. Overall dimension: 8000mmx800mmx1200mm
13. Shipping weight: 260kg
14. Automatic packing and cleaning line
The machine adopts Taiwan delta PLC control, can field adjustable, ensure that special flow operation of packing speed. More can adapt different quality packaging tapes, strapping speed, each only about 2.2 seconds. Avoid put oil, mechanical durable, simple operation. To adjust the tightness of rewinding, can satisfy all sorts of the reasonable strapping, will never fall off. The host can 24 hours of continuous use. Bundle of covering with placed in the lateral, change take easy. Use conveyor design automation strapping system.
1. Voltage/power:380V 50/60HZ 1.2KW
2. Package size:W100-800*H30-570mm
3. Tie up speed:2.2sec/Strap
4. PP ribbon width:9-14 mm
5. Weight :280kg
6. Over dimension:1900*650*1750 mm
7. Electric parts ,CHNT
8. Maintenance time : one year
9. Pneumatic components is AIRTAC 
Complaint
