Complaint
| PFA physical properties 1. Perfluoropropyl perfluoroethylene ether and polytetrafluoroethylene copolymer. Compared with polytetrafluoroethylene, the properties of the resin may be more than ordinary thermoforming direct processing 2. Its creep resistance and compressive strength are better than PTFE, high tensile strength, elongation up to 100-300%, good dielectric properties and excellent radiation resistance, high flame retardant, 3. Long-term use temperature -80-200 degrees, excellent chemical corrosion resistance, all chemical corrosion resistance of the pad, friction coefficient in plastic, and good electrical performance, its electrical insulation is not affected by temperature. |
| When choosing the right fluoropolymer for your process, consider some significant performance differences between the two fluoropolymers. The difference in alkoxy substituents allows PFA to be fused by conventional injection molding and screw extrusion techniques, while PTFE cannot. The PFA is more flexible, but has a lower flexural life, so it cannot withstand the ability to fold repeatedly. PTFE has slightly higher heat resistance, but is lacking in comparison to fluidity, creep resistance, and thermal stability. The melting points of PFA and PTFE are 260°C and 327°C, respectively. Although PFA has better salt spray resistance, water absorption and weather resistance have a greater impact on PFA than PTFE. Finally, the most significant difference between the two is that the dielectric strength of PFA is 3-4 times that of PTFE. |
| Water Absorption: | 1.5%-3.5% |
| Shrinkage Percentage: | 1.5%-5.0% |
| Compressive Strength: | 41-50MPa |
| Elongation at Break | 100%-300%: |
| Operating Temperature: | -200ºC-+260ºC |
| Material Characteristics: Resistant to all strong acids and alkalis. | |
| PFA Physical property table | |||
| physical properties | rated value | system of units | measurgin method |
| specific gravity | 2.14 | g/cm³ | ASTM D792 |
| Melt rate(372ºC/5.0kg) | 18-25 | g/10min | ASTM D1238 |
| water absorption(24hr) | 0.030 | % | ASTM D570 |
| hardnessl | 55-65 | - | ASTM D2240 |
| melting temperature | 302-310 | ºC | - |
| diameter | maximum diameter | diameter | maximum diameter |
| 5 | 6 | 55 | 56 |
| 12 | 12.7 | 60 | 61 |
| 15 | 16 | 65 | 66 |
| 20 | 22 | 70 | 71 |
| 25 | 26 | 75 | 76 |
| 30 | 31 | 80 | 81 |
| 35 | 36 | 85 | 86 |
| 40 | 41 | 90 | 91 |
| 45 | 46 | 95 | 96 |
| 50 | 51 | 100 | 101 |
| PFA resin includes emulsion, powder, granule and other forms, the difference is that the melting point of pfa is 290~312ºC, the melting finger is within the range of 0.8-30g/10min, the molding temperature is between 350~410ºC, and the pfa resin is used in molding, extrusion molding, injection molding and other processing processes When the melt finger of PFA extrusion molding is greater than 3.0g/10min, it can be processed by extrusion molding. The process and equipment of PFA extrusion molding can be used in common with the process and equipment of polyperfluorinated ethylene (FEP). When the melt finger of PFA product is in the range of 0.8~3.0g/10min, the molecular weight is relatively high and the viscosity is large. It is not easy to flow, and it is suitable for manufacturing molding by molding injection molding melting finger in the range of 16~30g/10min, which requires the production of various complex shapes of parts such as aerospace industry, electronic and electrical parts, medical chemical testers and other purposes | PFA Extrusion When the melting finger of PFA product is greater than 3.0g/10min, it can be processed by extrusion molding, mainly producing pipes, cable insulation layers, films, etc. The screw length to diameter ratio for PFA extrusion is generally 20:1, the extrusion temperature is usually controlled at 330~425ºC, and the speed is set at 3~50r/min. Due to the high melt viscosity of PFA products, there is a high tensile ratio during extrusion molding, and smooth extrudates can be obtained quickly. The process and equipment of PFA extrusion can be used in common with the process and equipment of polyperfluorinated ethylene (FEP), but the molding temperature needs to be further increased. There is also a critical shear rate of melt rupture for PFA, which is 50s-1 for high speed extrusion type and 3s-1 for low speed extrusion or molding type. The melt strength of PFA is higher than that of FEP, and the stretch ratio of PFA can be higher when forming thin tubes and monofilaments. | PFA injection molding When the melting finger of PFA products is in the range of 16~30g/10min, and it is necessary to produce various complex shapes of aviation, aerospace industry, electronic and electrical industry parts, medical, chemical testing equipment, etc., PFA can be processed by ordinary screw injection molding machine. Commonly used plasticizing ability of strong screw extruder, the mixing material uniform, less lag, fast transfer of stress to the mold, but with PFA molten resin contact screw, barrel and mold, etc., need to be made of corrosion resistant stainless steel, and the use of large diameter injection port, runner and pouring port, and the runner should be as short as possible, without any obstacles and sharp corners. It is best to be a circular flow channel that can be mixed with the gate, and all corners and intersections in the mold cavity are also round or streamlined, so that the molten resin flows in a streamlined manner. Taking these measures, and controlling the temperature of the melt, can avoid the phenomenon of melt cracking on the surface or inside the molding. |
1. Q: How long does the sample take? Is the sample free?
A: Usually 2-5 working days: For our stock products, it is free of charge, but shipping fee is charged. Samples are made according to your requirements, but the sample fee is refundable for bulk orders.
2.Q: How to confirm the customized products?
A: We can customize different sizes according to your requirements, firstly make samples and provide them to you.
3,Q:What is your minimum order quantity?
A: Usually our minimum order quantity is 1000 meters per piece, but if you need different sizes of products with different specifications, our minimum order quantity can be 100 meters per order, with no less than ten pieces of each style and each specification.
4, Q: How to know the price?
A: Price is the most important concern of every customer. If you want to know the price, you need to know the following details: product specifications, size, thickness, diameter, outside diameter, inside diameter, etc. These are the main factors that determine the price. The more you order, the lower the unit price you will get!
5. Q: What is your packaging?
Packing: The products are packed in cartons, there is one tube in a carton, we can do any other packing according to your requirements.
6. Q: What is your delivery time? Where is the shipping port?
A: Our delivery time is usually one month in peak season, 15 working days in low season, and the shipping port is Shanghai.
7. Q: What are your payment terms?
A: For orders less than 3000 dollars, full payment.
If the order is more than 3000 dollars, 50% prepayment and 50% before shipment.
8.Q: After-sales service?
A: We promise that if there is any quality problem different from the description of mass production, we will take the responsibility of the defective goods.
Q:Could you tell me something about your company
A:Fluorway Polymer Materials (Shanghai) Co., Ltd., located in Shanghai, China, is an enterprise situated within the national G60 Science and Technology Innovation Park. We specialize in the production and domestic and international sales of high-performance fluoroplastic semi-finished materials and precision processed components.Additionally, we provide MSDS reports to ensure the safe use of our products and help buyers mitigate any potential chemical incidents during usage and transportation. With over 20 years of experience in this industry, our company boasts a strong team of technical engineers and sales professionals.
