Armored Steel Tape

Min.Order: 5

Product origin: Zhenjiang, Jiangsu, China

Infringement complaint:

Complaint

US$ 1350 ~ 1850

Description

Basic Info

project		unit	index	tolerance
length		m	1000-5000	+/-50
width		m	12-1000	+/-0.5
Thickness	Steel base band	mm	0.105-0.200	+/-0.010
	plastic(EAA)	mm
	Total thickness	mm
Chromium plating on steel base band		G/ Square meter	0.08-0.34	+/-0.013
Composite strip tensile strength		MPA	310-390	+/-0.015
Elongation at break of composite strip		%	>20
The stripping strength of the steel strip and the film was observed			non-breakdown
Heat seal peeling strength of composite strip		N/cm	Level 8
Peeling strength of composite strip after water bath 68+/-1°C,168h		N/cm
Oil paste resistance of composite tape 68+/-1°C,168h	Umbrella plate	---
Oil paste resistance of composite tape 68+/-1°C,168h	WT-103	---
Dielectric strength of composite tape DC 2KV ,1min		---
Corrosion resistance of composite tape 0.1mol/L,Hc1.480h		Level
Heat seal shear strength of composite strip	Composite tape break or failure between steel and film

Product Description
1 range
This specification specifies the product type, requirements, test methods, marking, packaging, transportation and storage requirements of steel-plastic composite tape materials.
2 Adopting Standards
YD/T 7233-2007 metal-plastic composite tape for communication cables and optical cables -- Part 3 steel-plastic composite tape.
3 Product Labeling
Polythene single - side chromium - plated steel - plastic composite strip YG
Polythene double chrome plated steel plastic composite tape YGY
Polyethylene single side stainless steel plastic composite tape YB
Polyethylene double sided stainless steel plastic composite tape YBY
Copolymer type single - side chromium - plated steel - plastic composite strip EG
EGE is a copolymer type double chrome plated steel plastic composite band
Copolymer type single side stainless steel plastic composite tape EB
Copolymer type single side stainless steel plastic composite tape EBE
4 Specifications
Product Specification Type Code Grade steel strip nominal thickness mm surface chromium plating g/m2 Type code grade steel strip nominal thickness
Technical requirements and test methods
5.1 Appearance
The surface of the steel-plastic composite belt should be smooth, smooth, uniform, no impurities, no wrinkles, no spots, and no other mechanical damage defects;
5.2 The side of the uncut steel-plastic composite strip is allowed to be protected by 2mm to 5mm plastic film. The side edge should be smooth, free of curling, notch, burr and other defects, and the dislocation between layers should not exceed 5mm;
5.3 The side of the cut steel-plastic composite strip should be flat, the side unevenness should be less than 1mm, and the end face should be boundless, notched, burr and other mechanical damage. When pulled out, the edge should have no obvious waves (commonly known as flounces).
5.4 Dimensions
Dimensions and tolerances are in accordance with regulations.
Dimensions and tolerances Steel strip nominal thickness and tolerance mm Steel-plastic composite strip nominal thickness and tolerance mm plastic layer nominal thickness and tolerance mm steel-plastic composite strip nominal width and tolerance mm steel-plastic composite strip nominal length and tolerance mm
YG EG type YGY EGE type unsliced
5.5 Mechanical properties, environmental properties and dielectric properties
Mechanical and physical properties, environmental properties and dielectric properties of chrome-plated steel - plastic composite strip. Comply with the regulations. Mechanical properties, environmental properties and dielectric properties of stainless steel plastic composite tape.
Mechanical and physical properties, dielectric properties and test methods of chrome-plated steel - plastic composite strips No. Item Nomenclature specification
1 Tensile strength, MPa 310-390
2 Elongation at break, % ≥15
Peel strength between steel strip and plastic film, N/cm ≥6.13
4. For the shear strength of the hot-bonding zone of the steel-plastic composite belt, the bond between the N/cm plastic layer and the steel belt is destroyed first, while the hot-bonding zone between the plastic layer should not cause shear failure.
5. Thermal bonding strength of steel-plastic composite belt, N/cm ≥17.5
6 Water resistance, (68ºC±1ºC, 168h) N/cm 6.13
No delamination between steel strip and plastic film (68ºC±1ºC, 168h)
Corrosion resistance, (0.1mol/L, HC1, 480h) ≥7
9 dielectric
Strength single-side steel-plastic composite belt, 1kV d·c, 1min no breakdown
Double-sided steel-plastic composite belt, 2kV d·c, 1min no breakdown
Mechanical properties, environmental properties and dielectric properties of stainless steel plastic composite tape serial number item name indicator to be obtained
1 Tensile strength, MPa 460-750
2 Elongation at break, % ≥40
3 Yield strength MPa ≥170
Peeling strength between steel strip and plastic film N/cm ≥4
5 For the shear strength of the hot-bonding zone of the steel-plastic composite strip, the bond between the N/cm plastic layer and the steel strip is destroyed first, while the hot-bonding zone between the plastic layer should not cause shear failure.
6 The thermal bonding strength of steel-plastic composite belt N/cm ≥17.5
No delamination between steel strip and plastic film (68ºC±1ºC, 168h)
8 dielectric
Strength single - sided steel - plastic composite tape
1kV d·c, 1min no breakdown
Double-sided steel-plastic composite tape
2kV d·c, no breakdown in 1min
6 Winding requirements
6.1 The steel-plastic composite tape should be tightly wound on the steel tape or aluminum or equivalent pipe core, and the inner diameter of the pipe core should be 100mm±2mm, 150mm±2, 204±2mm, 406mm±3mm. The tube core length of the cut steel-plastic composite strip should be the same as the width of the steel-plastic composite strip, and the tube core length of the uncut steel-plastic composite strip should be less than 1mm beyond the end face of the composite strip. The tube core length of the uncut steel-plastic composite strip should be 5-10mm beyond the side of the composite strip.
6.2 When used vertically, the tape should not break down.
6.3 Two or more steel-plastic composite tapes are not allowed to be rolled on the same core tube.
6.4 Two joints are not allowed on the same plate (roll) steel-plastic composite belt, but butt welding joints are allowed. One joint is allowed if the length is less than 1.4km, and two joints are allowed if the length is 1.4km and above. The thickness of the joint should not exceed 1.5 times of the original thickness, and the plastic layer should be restored at the joint. The joint shall be marked, and the distance between the two joints shall be no less than 305m. The tensile strength of the steel-plastic composite belt with joints shall be no less than 85% of the adjacent steel-plastic composite belt without joints. The DC resistance of a 1m long steel-plastic composite strip with a connector shall be no more than 110% of the DC resistance of the adjacent 1m long steel-plastic composite strip without a connector.
7 Inspection Rules
For the steel and plastic composite tape supplied by the designated manufacturer, acceptance shall be carried out according to the supplier's warranty or test report, and sample preparation or test shall be conducted regularly.
8 Packaging
The steel-plastic composite belts and packing cases and the moisture-proof measures must comply with the provisions of 1.1 to 1.7 in Chapter 1 of GB/T3199. The maximum dimensions of packing cases are 1150mm long and 800mm wide. The cut steel and plastic composite tape is generally placed flat or upright. Each disk should be separated by cardboard or foam material. The core tube should be connected by paper tube and plastic to prevent loosening. Uncut can be placed flat or upright. The gross weight of each package is not more than 1.5 tons.
9 Mark
9.1 The qualified steel and plastic composite belt shall be affixed with a sign indicating:
a) Product labeling; b) Product trademark or manufacturer name; c) Date of production.
9.2 Each box of products to be delivered shall contain a packing list indicating:
a) Demander's name; b) Product label, number of product discs (or rolls), total length and total weight;
c) Production date; d) Product inspection status mark and manufacturer's name.
10 Accessories
Steel - plastic composite belt delivery, should be accompanied by the product certificate and quality guarantee. For the first supply, the type test report of the statutory inspection department must be attached. For normal supply, the type test of the statutory inspection department of the same year should be provided once every two years.
11 Transportation
Transport in a clean, dry environment, and avoid moisture and mechanical damage.
12 Storage
Ventilated warehouse, should be away from heat sources, and avoid direct sunlight, storage temperature should not exceed 50ºC
Detailed photo

About us
Jiangsu Chenfeng is a supplier of optical cable and aluminum foil materials with national standard qualification. Its products are widely used in various communication optical cables, cables, submarine optical cables, control cables, signal cables, track cables and air-conditioning condensers, as well as magnetic devices and hot water pipes. Flexible packaging and other fields.
Jiangsu Chenfeng has been designated in a number of orders from various telecom operators. Relying on its excellent product quality and perfect service, it has established a good reputation among telecom operators such as China Telecom, China Unicom, China Mobile and China Netcom. At the same time, it actively participates in international competition and has established many partners in the field of optical communication raw materials in the world, becoming an important supplier in the field of global communication and magnetic devices.
Jiangsu Chenfeng is a metal-plastic composite belt industry in China. One of the enterprises with large annual output is a trusted partner of global users.

Logistics service

Why choose us?

Jiangsu Chenfeng is China's metal plastic composite belt industry leader. One of the enterprises with large annual output, it is the trusted partner of global users.
Our goal is to provide one-stop metal materials solutions for our global customers, and we will make unremitting efforts to achieve this goal.

What can we supply?
Our company is a professional production of optical cable cable auxiliary steel belt aluminum belt manufacturers thickness we can do :0.165-0.32mm

We can make the width :535-810mm

How long is each roll? What is the net weight of each roll?

Roller size can be customized. We will produce according to customer's requirement. The estimated net weight can be calculated from the thickness, width and length of the strip.

Packing method:

Each roll of pallet wooden box packing way. Specific can be customized according to customer requirements
FAQ:
Q: Are you a trading company or a manufacturer?
A: We are a manufacturer that has been in the industry for over 10 years.

What are your terms of payment?
A: Usually 30% TT in advance and the balance before shipment. If there are any other conditions, please let us know at the time of inquiry.

Q: How long does it take to go from sample to mass production?
A: It usually takes 15-20 days and 25-30 days for new molds and free samples (less than 5kg) to be confirmed
The days of mass production.

Q: Is OEM/ODM available?
A: Yes, we can!

Q: Can you provide samples?
A: Yes, it's our pleasure to provide you with samples for quality inspection.

Q: Are sample orders accepted?
A: Yes, we accept sample orders. We can provide design services!

Q: Can you provide the certificate of origin?
A: Yes, we can provide CO, FTA, Form A, Form B, Form E and so on according to your request.

Q: How do you ensure quality?
A: We have a complete inspection system from raw materials to finished products. Every step must be checked and signed off by our professional team.

Q: Can we visit your factory?
A: Of course. You are sincerely welcome to visit us at any time!

Q: If I only need a small quantity, can you produce it?
A: Dear customer, because the minimum order quantity of steel coil raw material is 2 tons to 5 tons.