100m Optical Transceiver/Multimode Optical Transceiver/Single Mode Optical Transceiver

Min.Order: 10

Product origin: Shanghai, China

Infringement complaint:

Complaint

US$ 35

Description

General Introduction:
The Rayoptics RT-M40S85-C00 is a Four-Channel, Pluggable, Parallel, Fiber-Optic QSFP+ Transceiver for InfiniBand QDR/DDR/SDR,12G/10G/8G/4G/2G fiber channel, PCIe and SAS Applications. The QSFP full-duplex optical module offers 4 independent transmit and receive channels, each capable of 11.3Gbps operation for an aggregate data rate of 45.2Gbps 100m using OM3 fiber. These modules are designed to operate over multimode fiber systems using 850nmVCSEL laser array. An optical fiber ribbon cable with an MPO/MTP connector can be plugged into the QSFP module receptacle. QSFP+ SR4 is one kind of parallel transceiver which provides increased port density and total system cost savings.

Products Name:
QSFP+ SR4 100m optical transceiver with full real-time digital diagnostic monitoring and pull tab

Product Features:
1).Four-channel full-duplex transceiver modules
2).Transmission data rate up to 11.3Gbit/s per channel
3). Up to 100m on OM3 Multimode Fiber (MMF)and 150m on OM4 MMF
4). Low power consumption <1.5W
5).Operating case temperature: 0 to 70ºC
6).3.3V power supply voltage
7). Hot Pluggable QSFP form factor
8). MPO connector receptacle
9). Built-in digital diagnostic function

Applications:
1).Proprietary High Speed
2). Interconnections
3). InfinibandQDRandDDR interconnects
4). Data Center

Electrical Characteristics:
The following electrical characteristics are defined over the Recommended
OperatingEnvironment unless otherwise specified.

Parameter	Test Point	Min	Typical	Max	Unit	Notes
Differential input impedance	Zin	90	100	110	ohm
Differential Output impedance	Zout	90	100	110	ohm
Differential input voltage amplitude	ΔVin	300		1100	mVp-p
Differential output voltage amplitude	ΔVout	300		800	mVp-p
Bit Error Rate	BR			E-12
Input Logic Level High	VIH	2.0		VCC	V
Input Logic Level Low	VIL	0		0.8	V
Output Logic Level High	VOH	VCC-0.5		VCC	V
Output Logic Level Low	VOL	0		0.4	V

Optical Characteristics:
All parameters are specified under the recommended operating conditions with PRBS31 data pattern unless otherwise specified.

Parameter	Symbol	Min	Typical	Max	Unit	Notes
Transmitter
Center Wavelength	λC	840		860	nm	1
RMS Spectral Width	λrms			0.65	nm	1
Average Launch Power, each lane	PAVG	-7.6		2.4	dBm
Optical Modulation Amplitude (OMA)	POMA	-5.6		3	dBm	1
Difference in Launch Power between any two lanes	Ptx,diff			4.0	dB
Launch Power in OMA minus Transmitter and Dispersion Penalty (TDP), each Lane	OMA-TDP	-6.5			dB	1
Rise/Fall Time	Tr/Tf			50	ps
Extinction Ratio	ER	3.5			dB
Transmitter Eye Mask Margin	EMM	10			%	2
Average Launch Power OFF Transmitter, each Lane	Poff			-30	dBm
Transmitter Eye Mask Definition {X1, X2, X3, Y1, Y2, Y3}		{0.23, 0.34, 0.43, 0.27, 0.35, 0.4}
Receiver
Center Wavelength	λC	840	850	860	nm
Damage Threshold	THd	3.4			dBm
Overload, each lane	OVL	2.4			dBm
Receiver Sensitivity in OMA, each Lane	SEN			-9.5	dBm
Signal Loss Assert Threshold	LOSA	-30			dBm
Signal Loss Deassert Threshold	LOSD			-12	dBm
LOS Hysteresis	LOSH	0.5		8	dB
Optical Return Loss	ORL			-12	dBm

Digital Diagnostic Functions:
Digital diagnostics monitoring function is available on all RAYOPTEK QSFP+ SR4. A 2-wire serial interface provides user to contact with module. The structure of the memory is shown in Figure 3. The memory space is arranged into a lower, single page, address space of 128 bytes and multiple upper address space pages. This structure permits timely access to addresses in the lower page, such as Interrupt Flags and Monitors. Less time critical time entries, such as serial ID information and threshold settings, are available with the Page Select function. The interface address used is A0xh and is mainly used for time critical data like interrupt handling in order to enable a one-time-read for all data related to an interrupt situation. After an interrupt, IntL, has been asserted, the host can read out the flag field to determine the affected channel and type of flag.

Parameter	Symbol	Min	Max	Unit	Notes
Temperature monitor absolute error	DMI_Temp	-3	+3	ºC	Over operating temperature range
Supply voltage monitor absolute error	DMI_VCC	-0.1	+0.1	V	Over full operating range
Channel RX power monitor absolute error	DMI_RX	-3	+3	dB	1
Channel Bias current monitor	DMI_Ibias	-10%	+10%	mA

Main Export Countries & Areas:
Usa, Uk, Japan, Germany, Spain, France, Swiss, Korea, Russia, Mexico, Brazil, Argentina,Pakistan, India, Portugal, Canada, New Zealand, Australia, Saudi Arab, Turkey, Finland, Poland ,etc.

Payment Method: by T/T or Western Union.
Delivery time: 7-10 days.
Quality Warranty: Ruitaiphotoelectric(Raytekoptics) offers quality warranty for our optical transceiver products with "3R" policy. For any inferior-quality products, Ruitaiphotoelectric(Raytekoptics) is responsible for return, replacement and refund.

Forward

Related products