Description
1.What is Interactive Projector?
Q10 pro is an all-in-one interactive projector that can realize projector into a multi-touch board.
To work with it, you only need to open the projector power and press the red button on the surface
of the projector to finish the 4 point calibration, and then you can do anything what you want on the whiteboard with our e-pen. Such as drawing pictures, playing games, presentation, and so on...no installation of software or driver is needed.
Q10 pro is more than a projector, it is really a super combination that can make interactive whiteboard and ordinary projector to be all-in-one. 2.Product description:
1.1920*1080P Native Resolution,Compatible with up to 4K 30fps.2. 2GB RAM 32GB ROM, upgrade large memory.
Upgrading to WiFi 6 will allow communication with up to 8 devices at a maximum rate of 9.6Gbps.
3. 9800 Lumen high brightness projector,520 ANSI lumen.
4. 4Ω 5W*2 stereo speakers.
5. support Bluetooth output.
6. Support 80%-100% display zoom and easy to adjust the color by your preference.
7. The projector with the smallest HDMI-Compatible in delay,
the best 1lcd projector for playing 60fps video.
8. LED as the light source, which can used up to 30,000hours.
9. Android version, 2gb+32gb large memory, you can download what you need.
10.No need to install any software or driver.
11.4-point calibration.
12.Supports up to 10-point multi-touch
13.Zero host system resource occupation and works well on low-speed systems3.Specifications: | Q10 PRO |
| Model | Q10 PRO |
| Lamp: | LED Lamp |
| Lens | Manual Correction |
| Brightness: | 9800 Lumen |
| Weight | 3.71kg |
| Projection Distance: | 1.8-5m |
| Operation System: | Android 9 |
| Projected Dimension: | 40-120 inches |
| Light Source: | LED |
| Projective Mode: | Throwing,Ceiling,Back Projection |
| Style: | LCD |
| Contrast Ratio: | 10000:1 |
| Resolution: | 1920x1080dpi |
| Lamp: | LED Lamp |
| Built-in Speaker: | YES |
| ANSI Lumen: | ±500 |
| Screen Scale: | 4:3/16:9 |
| Use: | Business & Education, HOME THEATER |
| Infrared pen |
| Model | P20B |
| Signal source | 940nm infrared |
| Nib trigger mode | Omni-directional pressure trigger |
| Lateral sensitivity | < 35g |
| Dynamic sensitivity | <0.8mm |
| Power source | Supper capacitor |
| Charging method | Micro USB |
| Charging voltage range | 4.5V~5.5V |
| Charging time | ≤3 minutes |
| Rechargeable times | No limit |
| Full power run time | 1 to 2 hours for normal use |
| Charge retention time | 72 hours |
| Nib trigger life circle | >1 million |
| Volume | Length 18cm;Diameter 13.5mm |
| Weight | 27g |
4. Start to useCoordinate calibration
When you use the product for the first time or the device is moved after last calibration, you need to do calibration.
Under the Android system, when the open the projector successfully, and then press the red calibration button on the front of the projector, and release it after 2 seconds. A beep will be heard. At this point, 4-corner calibration will be activated. Press the pen tip on 4 corners of the display area by sequence from 1 to 4 to finish the calibration. Please note that a beep must be heard before you move to the next corner. After calibrating successfully, you will hear two short beeps. Then you can use the product.5.FQA
Q:Do I need to do calibration every time I start the device?
A:For the first time using, calibration is needed. You do not need to do it later if there is no positional movement between the device and the display.
Q:Why is Tallpic's Plug-and-Play products more smooth and quick?
A:Compared with the normal USB camera based software solutions, Tallpic's pure hardware interative product such as MaxPro/TVT, are free from image transfer delay, image compression/decompression delay and loss,etc.
Q:Why there is a position shift when writing?
A:There are several possible reasons: 1.If the whiteboard is not flat, the position of the convex and concave portion will deviate. 2.The position of the pen was not accurate when doing calibration. 3.The display area is not complete especially when the computer is connected to the projector or LCD through a VGA cable, please check the display. Q:Can I use the product when there is strong light?
A:This product is for indoor use. If the sunlight directly shines at the screen, it may interfere with the reception of the pen signal. Thus the device can not work. Q:Why a lot of incorrect touch noise appear when a LiDAR camera or mobile phone with LiDAR is close?
A:Because most LiDAR products emit 940nm laser.It's a strong noise source to our sensor.
Q:What are the advantages of Tallpic's infrared pens?
A:1)Tallpic's infrared pen(P20B,P21SC, etc.) are all-direction pressure sensitive other than axial sensitive. While most other known products are only axial pressure triggered, they are difficult to be triggered in some cases.
2)Most of Tallpic's infrared pen uses super capacitor as electrical energy storage device. Its special advantages are: No battery pollution; No material cost; Unlimited charging life cycle; Fast charging and no worry for the battery's suddenly running out; Light weight and not subject to air transport restrictions.Q:.Why do some of the projectors have dust?
A: Because during the transportation of LED projectors, usually one or two dust from the exhaust port into the projectors, this is a phenomenon that often happens.6.Our Service:Warranty:The signal receiver is guaranteed for three years.
Under warranty,if any non-human damage happen, we'll offer free repairing or replacement, including delivery cost.
Out of warranty: we offer repairing parts at lower cost, and service free in charge.
7.Company Information:
8.Certificates:
Our Service:Warranty:The sign receiver is guaranteed for three years.
Under warranty,if any non-human damage happen, we'll offer free repairing or replacement, including delivery cost.
Out of warranty: we offer repairing parts at lower cost, and service free in charge.
Payment:TT
Contact:
Address: 3F-B BLD-2, R&D ZONE 1, XUZHUANG SOFTWARE INDUSTRY BASE , XUANWU ROAD 699-8,NANJING CHINA
Website: tallpic.en.made-in-china.com
Complaint
