Surface Cleaning Rubber Belt Sand Blasting Machine

Min.Order: 1

Product origin: Qingdao, Shandong, China

Infringement complaint:

Complaint

US$ 2500 ~ 24000

Description

Product Brief Introduction

Rubber type shot blasting machine is designed according to user requirements of a new special shotblast cleaning equipment, used for castings and forgings, small round spring, bearing the workpiece blasting. This equipment blasting quantity is bigger, better sealing, cleaning efficiency, production efficiency and dust removal effect with the larger, use rolling Mn13 chamber body guard, maintenance cost reduced by about 60%. Through strengthening the shotblast cleaning, not only can remove rust, scale, casting surface after sand and so on, also can reduce the internal stress of workpieces, improve the fatigue strength. This machine can use single also can use wiring, has high cleaning efficiency.

Working Principle
Within the clean up the warehouse after joining stipulated number of artifacts, the door closed, the machine start, artifacts are drum drive, began to turn over, with the high-speed projectile blasting when fan beam, evenly hit the workpiece surface, thus achieve the purpose of cleaning. Thrown out of the rock and sand holes from the caterpillar, into the bottom of the screw conveyor, the screw conveyor into the elevator, the elevator mentioned separator in the separation. Dust by gas suction fan after filter to filter, into a clean air, the atmosphere, the dust by air blow into the filter dust at the bottom of the box, the user can be cleared on a regular basis. Used sand by waste pipe flow, the user can reuse. Pill sand mixture by recycle tube recycled into Chambers, stay again after separator separation recycling. Shot blasting machine layout of 3 d dynamic simulation through the computer, all the Angle of the layout, location, design by computer. In the care of all need to clean up the workpiece

Shotblast Cleaning Room

Welding chamber system structure, by the chamber shell, roof and interior protective parts. Room at the bottom of the shell has a screw conveyor, internal with caterpillar and its transmission mechanism, end with a side dish, internal adopts wear-resisting armor protection, roof fixed his shot. Safety blasting design simple and reliable safety protection device, when the equipment operation, maintenance, lubrication, as well as the device can protect card into the clean room staff absolutely safe

Operation And Matters Needing Attention

1, all the machine operator must be to this specification and its principle of work performance and operation method, lubrication, etc have a comprehensive understanding, in order to operate;

2 will the projectile (200 kg) in succession to join chamber body, and then into the workpiece, closed loading door, ready to drive;

3 start the filter fan;

4 start button: in order for pill gate hoist, shot blasting machine, and began to clean up. Cleaned up after the button closure in turn: used for pill gate, shot blasting machine, elevator, dust collector fan, restart vibrating motor ash removal, to a certain time after the shaking stopped;

5 after shot blasting machine stop completely, open the door of feeding, will the tooling and artifacts.

6 in case of an emergency, can according to the urgent stop button, the machine immediately stop all work;

7 all the work has been completed, should be timely close the filter;

Matters Need Attention

1, each work after work, all the machine should be clean again;
2, often should examine the guard in the clean room and shot blasting machine, round pill and orientation in the set of wear parts wear, wear serious, should be replaced immediately;
3, should be lubricated periodically according to the rules, and regularly check whether the machine regulated flexibly.
4, check the transmission parts regularly, cleaning parts, replace worn components.

Product's Technical Parameters

NO.	TYPE ITEM		3GN	8GN	8GN-5R	15GN
1	Productivity	T/H	0.6-1.3	2-3	2-4
2	Feeding amount	KG	220	630	630	1362
3	Max.Weight of single piece	KG	12	35	35	227
4	Diameter of and disk	MM	Ø650	Ø1000	Ø1000	Ø1400
5	Effective volume	M3	0.15	0.3	0.3	1.6
6	Abrasive flow rate	KG/MIN	160	270	270	360
7	Ventilation capacity	M3/H	2000	3500	3500
8	Power consumption	KW	12.6	23.07	27.3	40.3
9	Outline dimensions	MM	150018803900	397219604568	397636004668
10	Belt		RUBBER	RUBBER	RUBBER	METAL

Equipped With Dust Collector

1.Air inlet, Air discharge and reverse blowing system: including gas inlet pipes,gas inlet room,reverse blowing valve, reverse blowing pipes, three way pipe,gas discharge valve,gas discharge pipes.

2.Bag chamber construction : including dust hopper, access door, frame ontolog,Top and bottom plate, bag filter, filter chamber.

3.Ash discharge system: including ash discharge valve,screw conveyer.

1.It is used to treat exhaust gas of high concentration,large air flow, high temperature and humidity etc.

2.It uses positive pressure reverse sucking air separate chamber offfline dust clearing.

3.It uses PLC to realize automatic dust air cleaning, dust particle removal, automatic temperature control

Shot Blasting Machine Blast Wheel

1. Blast Wheel is a new kind of imp eller head with high efficiency, simple structure and low noise .

2.The 8 Blades are inserted on the wheels and firmly fixed by the centrifugal force of vane wheel revolving ,no need to use any clamp apparatus.

3.Simple design of blade locking guarantees a quick turn or change of blades.It will only take 3 to 5 minutes to disassemble the 8 pieces blades.
Direct-Driven Blast Wheel
Straight league blasting is a new type, efficient shot blasting machine, with beautiful shape, compact structure, low noise, energy conservation, environmental protection, etc

Belt-Whell Blast Whell
Belt shot blasting machine is a kind of traditional shot blasting machine, with a large amount of blasting and cleaning effect is good wait for an advantage.The essential components of equipment is a large clean up

FAQ

Q: What standards are you carrying out for your products?
A: We produce according to the ISO9001 and ISO14001 rules.
Q: How to install the machine?
A: We will arrange 1~2 engineers to your factory to guide installation and assembly.
Q: What's your international market?
A: We Have exported to about 40 countries and regions all around the world, such as, the USA, France, Singapore, Australia, Middle East, Brazil, Peru and so on.
Q: What's your productivity?

A: We have three production lines for steel shot and steel grit production, one work shop for steel cut wire shots, and one workshop for stainless steel shot and Aluminium shot and so on.

Why Choose Us ?

1. Our company has passed "CE", "ISO9001" and bureau veritas certification .

2. 50 years experience with 20 professional engineers in our Qingdao Foundry Machine Co.,Ltd.

3. So many kinds of foundry machinery ---100 kinds of shot / sand blasting machines and 80 kinds of casting machines.

4. Considerate after-sale service , Technial Assistance and provide installing ,debugging and training on site

5. The company has its own foreign trade marketing team Industrial Corporation, first - class service standards for all clients.

Our company has passed ISO 9001:2008 certified,we can offer OE service

Forward

Related products