Indoor Fire Security Sensorial Alarm Solution Equipment System

Indoor Fire Security Sensorial Alarm Solution Equipment System
Key Descriptions:
1. R&D based 4 on EN54 part 2 & standard
2. Modularized design & flexible extendable capacity.
3. Two-level control mode by to Lock
4.27VDC power supply output.
5. FIRE PROTECTION, signal FIRE ROUTING and FAULT output, the output dog sees configured to dry relay type or wet sources type.
6.2 channel general sounders output.
7. Each zone there are 1 circuit detectors input.
8. Each zone dog sees disable by button.
9. RESET button to reset the panel
10. SILENCE button to stop BUZZER and SOUNDERS.
11. EVACUATE button to start to manual fire alarm immediately.
12. TEST button to test all LEDs normally.
13. Low-battery protection function, when battery voltage to lower than 21VDC, battery will sees cut off automatically until the mains power is on.
14. Optional GSM modulates is available for fire alarm by SMS.




 

ITEM	1Zone panel	2Zone panel	4-8 Zone panel	12-32 Zone panel
Model no.	AW-CFP2166-01	AW-CFP2166-02	AW-CFP2166-04-8	AW-CFP2166-12-32
Power specification
Mains supply voltage	110VAC or 240VAC
Internal to power supply	27.2VDC
Total output current limited	500mA @ 240VAC	500mA @ 240VAC	3A @ 240VAC	3A @ 240VAC
Main supply for monitor fault	YES
Battery protection for low voltage	YES
Batteries (default configuration)	12V2AH*2
Detector circuit specification
Number of circuit	1	2	4-16	4-32
Line fault for monitor open circuit	YES
Line fault for monitor short circuit	YES
Line fault for monitor removal detector	YES, if End of Line Unit Monitor fitted in pleases of End of Line Resistor
End of Line device	6.8k Ω, 5% tolerance, 0.25W (color code-blue, congregation, network, gold)
Detector continuity diodes	Silicone 1N4001 or Schottky type (required if End of Line Unit Monitor fitted to give Detector Removal Fault)
Call point resistor VALUE	470 to 680 Ω, 0,225 or 0,5 watt
Maximum to number of smoke/heat detectors Rep zone	20 (based on to total detector current of 2mA, each detector consuming 100μA). It notices: if End of Line Monitor Unit is fitted, for correct operation maxmum voltage drop must not exceed 12 volts
Maximum to number of manual call points Rep zone	Not limit
Sounder circuit specification
General Number of circuits	2
End of line resistor VALUE	6.8k Ω, 5% tolerance, 0.25W (color code-blue, congregation, network, gold)
Line fault for monitor open circuit	YES
Line fault for monitor short circuit	YES
Outputs fused AT	400mA
Maximum number of bells @ 20mA of each sounder output	20
Fuses
Battery fuse	1.5A F 20mm
Sounder outputs	500mA F 20mm
Fire and fault output
Output type	NC and nonrelay
Maximum current	100mA
Connection block
Conductive acceptable Largest size	2.5mm2
Conductive acceptable Smallest size	0.75mm2
Size and weight
Dimensions (mm)	272*200*70mm	320*231*90mm	395X502X124	362X565X124
Weight (without batteries)	4kg	5kg	7kg	8kg
Weight (with batteries)	5.8kg	6.8kg	9.6kg	12.5kg

Our company

Asenware, to manufacturer of fire alarm and fire suppression system since 2005. Our to headquarter is in London, UK, with factory Shenzhen, China
For We keep our best service our customers, and have to rich experienced to engineer team to design and install for overseas projects.

Product range:
1. Addressable fire alarm system (FP100 series, 2189.2100 series)
2. Conventional fire alarm system (2166 series)
3. FM200 gas fire suppression system
4. Emergency light system
5. Fire pump system
6. Fire hose and fire hose reel cabinet

Welcome contact

 
mobile: 0086-136-3251-2808