Complaint
| Product Name | Electric heating type DPF high temperature regeneration equipment | |
| Main technical parameters | ||
| Model | KL-DZL15 | KL-DZL40 |
| Power | 15 kW | 35 kW |
| Heating rate | 30ºC/min | 44ºC/min |
| The chamber size | 500×550×700mm | 800×800×700mm |
| Boundary dimension | 1050×850×1880mm | 1350×1100×1880mm |
| The substrate capacity | Single loading of a diameter of 330mm or Two DPF carriers with 190mm diameter substrate | A single loading of four diameters of 330mm or Six DPF carriers with 190mm diameter substrate |
| Power supply | Three-phase five-line system,380V,50Hz | |
| Temperature range | Normal temperature~750 ºC | |
| Temperature control tolerance | ±5ºC | |
| Electric control system | Temperature control module,7-inch all-piece touch display | |
| Fresh air system | Fresh air fan supplies oxygen and cooling, and automatically controls the intake volume | |
| Product Name | Electric heating type DPF high temperature regeneration equipment | |
| Model | KL-DZL25 | |
| The chamber size | 500×550×700mm (can meet the package φ 450 outer diameter, length ≤450mm) | |
| Power/air source | 380v power supply; Air source pressure: 0.6 ~ 0.8mpa, air consumption ≤30L, intake interface for φ 12 quick connector | |
| Temperature range | Normal temperature ~ 620ºC, maximum temperature 650ºC | |
| Heating power | 24KW, heating rate: 28ºC/min | |
| Stages of temperature control | Set three stage temperature, reach the set value for automatic constant temperature. Temperature control tolerance: set temperature ±10ºC | |
| DPF cooling | For high temperature DPF cooling, two butterfly valves, inlet and exhaust, are used to open and inhale cold air and discharge hot air for cooling and cooling after the end of insulation | |
| Motor power | High temperature resistant 0.37KW three-phase motor, flow 1100m3/h | |
| Surface treatment | Surface paint treatment | |
| Door quantity | Single door, each side of the door is installed with high strength hinge, strong jacking force, easy to operate. | |
| Insulation material | 128kg/m3 high density aluminum silicate thermal insulation cotton, with flame retardant, heat insulation and good thermal insulation performance | |
| Protector | Leakage protection, lack of phase protection, motor overcurrent protection, overtemperature heating protection | |
| Product name | Standard DPF purging and testing equipment | |
| Model | KL-DCJ30 | |
| Main technical parameters | ||
| Power supply | 220V,50Hz | |
| Fan | Maximum air volume:1060m3/h;maximum vacuum:5kPa | |
| Boundary dimension | 1100×800×1880mm | |
| Blow control | Overall pulse purge, PLC automatic control, purge at the same time, vacuum dust collection | |
| Weighing detection | Weighing table range 30Kg,Weigh accuracy: ± 1g; the data can be recorded | |
| Back pressure detection | PLC controls automatic detection and data can be displayed and recorded | |
| Light detection | A 150w high-brightness LED light source, optical flux: 15,000 lumens | |
| Grey collecting device | Vacuum suction, 5 micron level can be cleaned, replacement of the filter element, drawer type dust collection room | |
| Gas storage tank capacity | Using 30L air storage tank, no need for manual intervention pressure regulation, automatic program control purge | |
| Electric control system | A 7-inch integrated touch display screen, with PLC programming control | |
| protector | Leakage protection, phase absence protection, motor overprotection | |
| Surface treatment | Electrostatic powder baking paint | |
| Product name | Fuel heating type DPF high temperature regeneration equipment | ||
| Serial number | Project | Unit | Parameter |
| 1 | Model | - | KL-DZT30 |
| 2 | Rated heating power | kW | 30 |
| 3 | Maximum quantity of wind | m3/min | 4 |
| 4 | Maximum wind pressure | kPa | 30 |
| 5 | Temperature control accuracy | ºC | ±20 |
| 6 | Service voltage | V | Single-phase AC220 |
| 7 | Power load | kW | 2.2 |
| 8 | Fuel tankage | L | 10 |
| 9 | Boundary dimension | mm | 1370x690x1210 |
| 10 | Net weight | kg | 200 |
