PCS1200 PLC CPU Module (10-CH 24VDC input & 6-CH relay output) Programmable Logic Controller Support Codesys

Technical Specifications

Support Codesys v3.5 SP13
 

CPU				Main parameter of electrical source
I/O		10-CH 24VDC input 6-CH Relay output		Supply Voltage	220VAC @50Hz
Expansion capability		Up to 20 modules can be extended (relay module is required)		Allowance range	187~264VAC @50Hz
Storage capacity		Program area : 400KB		Maximum current	120mA
		N Area : 8KB  M Area : 5KB		Output Voltage	24VDC
		Power loss holding area : 2KB		Output  Current	400mA
Timer		Hardware timing : 1, 0.1ms ~ 500ms No limit on software timing (min. 1ms)		Short-circuit protection	800mA,24VDC output
Counter		16bit		Communication interface	1*RS232, 2*RS485
Operating rate		0.06μ s(Boolean operation instruction)			1*RJ45
Interrupt input		4		Communication protocol	Serial MODBUS RTU protocol, custom protocol
Analog potentiometer		2 ,0~255			MODBUS TCP, 4 Server links
Input Channal				Output Channal
Type of input		P/M-lesend		Type of output	Relay
Input signal		Rated voltage 24VDC		Output signal	Rated voltage 24VDC or 24 ~ 230VAC
		0 ~ 30V DC			5 ~30VDC or 5 ~ 250VDC
Input signal (ON)		15~30VDC and > 3 mA		Common terminal output current summation	< 5A
Input signal (OFF)		0~5VDC and < 1mA		Output contact capacity	2A, Impedance load
Input delay		< 0.6ms (Rated input voltage)		Switch delay	< 10ms
Isolation method		Optoelectronic isolation		The isolation voltage between the coil and the contact	3000V AC, 1min, leak current 1mA
Isolation of pressure		1000VDC		Isolation voltage between contacts	750V AC, 1min, leak current 1mA
				Mechanical life of relay	Without load, it can reach more than 10,000,000 times; Rated resistance 2A load, up to more than 100,000 times
Dimensions and Mounting				Work Environment
Dimensions		120mm(L)×80mm(W)×63mm(H)		Operating temperature	0 ~ +55ºC
Weight		380g		Storage temperature	-40 ~ +70ºC
Way to install		35mm DIN rail		Relative humnidity	5% ~ 95% Noncondensing
		Panel mounting type

Main interface and terminal definitions


1.Switch: RUN and STOP are used to control the 2107N program to RUN and STOP. If the RS232 interface communication parameter of PCS1200 PROGRAMMABLE logic controller is modified, the program can only be downloaded by dial STOP.
2.Ethernet communication interface: RJ45 interface, which can be used for communication with touch screen, upper computer, cloud server, etc., supports MODBUS TCP protocol, and links four clients simultaneously.
3.Indicator light: RUN, COM and ERR are respectively used to display module operation, communication and fault status; I and Q are respectively used to indicate input and output status of each channel; ETH, C1 and C2 are respectively used to indicate communication status of A1B1, A2B2 and Ethernet interfaces (flashing indicates data receiving and receiving at corresponding interfaces).
4.RS232 communication interface: This interface is terminal wiring, which can be used for 2107N program download, communication with touch screen, upper computer, etc. It supports MODBUS RTU/ custom protocol, instruction library is RS232.lib;
5.RS485 communication interface: Two interfaces can be used to communicate with touch screen, upper computer, third-party instrument, etc. MODBUS RTU/ free protocol is supported. Instruction library is RS485. Lib and RS4853.lib respectively.
6.Module input terminal: it is composed of common terminal 1M and input point I, and the source/leakage connection method can be adopted.
7.24VDC power supply outside the module: VO+ and VO- are the positive and negative terminals of 24VDC respectively;
8.Extension interface: This interface is the base for inserting pin, which can be used to extend RPC2000 series extension modules;
9.Module power supply: L, N, GND respectively are the fire line, zero line and protective ground terminal of AC220V power supply;
10.Module output terminal: it is composed of 1L power supply drive end and output point Q, and the terminal is relay output;

Terminal tag definition specification
 

Terminal	Terminal instructions	Terminal	Terminal instructions
*	Undefined	A1+	The positive pole of the first RS485 interface
1L	Output common	B1-	The negative pole of the first RS485 interface
Q0.0	Normal Output terminal	A2+	The positive pole of the second RS485 interface
Q0.1	Normal Output terminal	B2-	The negative pole of the second RS485 interface
Q0.2	Normal Output terminal	1M	Input common
Q0.3	Normal Output terminal	I0.0	Normal input terminal
Q0.4	Normal Output terminal	I0.1	Normal input terminal
Q0.5	Normal Output terminal	I0.2	Normal input terminal
GND	GND	I0.3	Normal input terminal
N	Neutral wire	I0.4	Normal input terminal/External interrupt input
L	Live wire	I0.5	Normal input terminal/External interrupt input
TX	RS232 data sender	I1.6	Normal input terminal/External interrupt input
RX	RS232 data receiver	I1.7	Normal input terminal/External interrupt input
GND	RS232 ground terminal	I1.0	Normal input terminal
*	Undefined	I1.1	Normal input terminal
CGND	RS485 interface shielding ground	VO-	External power supply :positive
		VO+	External power supply :negative

Input channel connection mode





Output channel connection mode





About CHINT

Founded in 1984, the Chint Group provides safe, reliable and stable industrial electrical equipment and solutions for energy efficient management systems. With 30 years of development it has grown to be Asia' s largest low*voltage electrical product supplier and is the leading brand of the whole industry chain in industrial electric in Asia. With three R&D centers located in Europe, North America and China, there are also branches in over 20 countries and more than 30.000 employees in the world. CHINT provides reliable products, system solutions and services to more than 100 countries worldwide.






•   3 Global Research Centers: Europe, North America, Asia Pacific
•   6 International Marketing & Sales Area: Asia Pacific, Middle East and Africa, Europe, Latin America, North America, China
•   9 Manufacturing Bases: China (Wenzhou, Shanghai, Hangzhou, Jiaxing, Xianyang, Jiuquan), Thailand, Egypt, Germany
•   22 Logistics Centers 14 International Subsidiaries 17 Marketing Offices in China 2300 Sales Companies


About Chitic

Chrtic Control Engineering Co.. Ltd. is a subsidiary company of Chint, and a leading provider of automation & control technologies and applications in China that helps the industry customers to improve operating safety, reliability and efficiency. Chitic has series of products including PCS1800 DCS, TDCS9200 DCS and CTS700 DCS, information platform for water company, control system for high speed rapier loom, drive system of switched reluctance motor, solar energy monitoring system, computing cloud center for new energy; etc. Chitic control system won 2006 National Science and Technology Progress Awards of China, CTS700 DCS won the award of 2010 Innovative Product of China. Chitic headquarter is located at the beautiful city of Hangzhou, two hours drive from Shanghai. Chitic has its own science & technology park, Chitic Park, which covers about six thousand square meters.

Our Business Sector





Typical Reference